Craftsman 247.88045 manual Assembly, Removing From Crate, Place the shift lever in the F6 position

Page 6

ASSEMBLY

NOTE: References to right or left side of the snow thrower are determined from behind the unit in the operating position (standing directly behind the snow thrower, facing the handle panel).

Removing From Crate

1.Remove screws from the bottom of the crate securing the sides, and ends of the shipping crate.

2.Lift off the top off of the crate and set out of the way of the assembly area.

3.Remove and discard plastic bag that covers unit.

4.Remove any loose parts included with unit (i.e., Operator’s Manual, etc.).

5.Push down on the lower handle and pull unit back out of crate.

6.Make certain the crate has been completely emptied before discarding it.

assembly

1.Make certain the springs at the lower end of the auger and drive cables are securely hooked into their respective actuator bracket before pivoting the handle upward.

a.Place the shift lever in the F6 position.

b.Remove the lower wing knob and carriage bolt from each side of the upper handle. Pull up on upper handle as shown in Fig. 1. Align upper handle with the lower handle. Again,

make certain the springs at the lower end of the auger and drive cables are securely hooked into their respective

actuator bracket. Also, remove any rubber bands securing the cables to the wing nuts.

2.a. Secure the upper handle and lower handle with the two wing knobs and carriage bolts removed earlier.

b.Tighten the two wing knobs already installed in the upper holes to firmly secure the upper handle and support tubes.

3.Align the upper and lower shift rods, then slide the shift rod connector down over the end of the lower shift rod. Tap the connector until the lower rod is completely through the connector. See Fig. 2.

NOTE: If the connector is not properly assembled, the shift rod will pivot and you will not be able to change speeds or direction.

NOTE: If the full range of speeds (forward and reverse) can not be achieved, refer to the “Making Adjustments” section.

4.a. Cut the cable tie securing the chute assembly to the lower chute crank rod for shipping purposes.

b.Remove the internal cotter pin from the upper chute crank. Slide the upper chute crank into the sleeve on the lower chute crank. See Fig. 3.

c.Align the hole in the upper chute crank with the hole in the sleeve (If necessary, use a pair of pliers to assist in aligning holes). Insert the internal cotter pin through the holes to secure the chute crank. See Fig. 3.

5.Remove lock nuts and screws securing one of the flange keepers to the chute assembly.

Figure 1

Figure 2

a

b

Figure 3



Page 5 Page 7
Image 6
Page 5 Page 7
Contents Form no 28/2007Table of Contents Warranty StatementProduct Specifications Model Number Safety Instructions TrainingPreparation Maintenance & Storage OperationSafety Labels USE CLEAN-OUT Tool to Unclog Discharge ChuteRemoving From Crate AssemblyAssembly Place the shift lever in the F6 positionChute Clean-Out Tool Set-UpDrift Cutters Skid Shoes AdjustmentsTire Pressure ControlAdjusting Drive and Auger Controls Testing Auger Drive ControlTesting Drive Control & Shift Lever Retighten nuts and bolts securelyOperation Skid Shoes Chute AssemblyThrottle Control Recoil Starter HandleClean-Out Tool Before Starting EngineStarting The Engine To Engage Drive Replacing Shear PinsStopping The Engine To Engage AugersChanging Engine Oil Service and MaintenanceChecking Engine Oil Oil FIll Oil DrainLubrication Shift Rod Shave Plate and Skid ShoesShave Plate Chute ControlChute Bracket Belt replacementDrive Control Auger ControlAuger Belt Replacement Housing forward and pulling up the handlesLoosen the bolt shown in securing the belt keeper Drive Belt Replacement If also replacing the drive belt, proceed to the Drive BeltChanging Friction Wheel Belleville Washer Slide Hex Shaft Out Right SideGas in the tank † Under heavy load or in high temperatures Each Use Engine oil level CheckPreparing Snow Thrower OFF-SEASON StoragePreparing Engine Short-Term StorageTroubleshooting Parts List Craftsman Snow Thrower ModelHousing, Auger 684-04151 39 -04020 Spacer, 1.004 x 1.375 x 721-0146Parts List 61 -0199A Bumper, Rubber 784-5619B 41 -0963 Connector, Shift Rod79 -04220 Harness 80 -1364 Housing 81 -0225 Grommet 77 -1658 Lamp 725-166979 8 1478 61 49 3173 37 -0104 Pin, Internal Cotter From previous Craftsman Engine Model OH358SA-223828 For Snow Thrower Model Oil Drain Extension Not Available 37083 Cylinder Incl , 20, 72Dowel Pin 30969 Extension Cap, 1/4-18 NPT 28277 Flat Washer37085 Intake Pipe 35079A Key Switch Bracket Incl a28425 35691 Governor Link400 36947B 351 32180C Primer Line 355Packaged 740053B MarkedPage Sears Emission Control Defects Warranty Coverage This page applicable in the U.S.A. and Canada onlyPage Repair Protection Agreement Especificaciones DEL Producto ÍndiceDeclaración DE Garantía Número DE ModeloInstrucciones DE Seguridad CapacitaciónPreparativos Operación Mantenimiento y almacenamientoExtracción de la unidad del cajón Coloque la palanca de cambios en posición F6Montaje MontajeConfiguración Herramienta de limpieza del canalCortadores de desplazamiento de nieve Ajustes Presión de los neumáticosZapatas antideslizantes Prueba de control de transmisión y palanca de cambios Prueba del control de la transmisión de la barrenaVea Ajuste de transmisión y controles de barrena Llave de encendido Palanca de cambiosOperación FaroBotón del arrancador eléctrico Control del estranguladorManija del arrancador de retroceso Salida del arrancador eléctricoHerramienta de limpieza Control del canal de 2 direccionesControl direccional del canal Antes de encender el motorProcedimiento para engranar las barrenas Detención del motorProcedimiento para engranar la transmisión Arrancador de retrocesoControl del aceite del motor Servicio Y MantenimientoMantenimiento de Motor Cambio de aceite del motorLubricación Varilla de cambio Placa de raspado y zapatas antideslizantesPlaca de raspado Control del canalSoporte del canal Cambio de correaControl de la transmisión Control de la barrenaNota Asegúrese que la posición del regatón en la vara de Reemplazo de la correa de la barrenaDel motor. Vea la Figura Holgazán de taladro es mantenidaMotor e instale nuevamente la cubierta de la correa Reemplazo de la correa de transmisiónBarrena al eje de entrada Ranura de polea AdaptadorCambio de la rueda de fricción Eje hexagonalDeslice el separador sobre el extremo del eje hexagonal Cada Uso Nivel del aceite de motor Comprobar Tanque † Bajo carga pesada o en temperaturas altasPreparación de la máquina quitanieve Almacenamiento Fuera DE TemporadaPreparación del motor Almacenaje a Corto plazoSolución DE Problemas Esta página se aplica sólo en EE.UU. y Canadá Piezas con garantíaMotor certificado Acuerdo DE Protección Para Reparaciones Get it fixed, at your home or ours

247.88045 specifications

The Craftsman 247.88045 is a versatile lawn tractor designed to simplify lawn care for homeowners who seek both efficiency and ease of use. This powerful machine stands out with its robust features and technologically advanced design, catering to various landscaping needs.

One of the key features of the Craftsman 247.88045 is its powerful 24 horsepower Briggs & Stratton engine. This reliable engine ensures smooth operation and ample power to tackle a variety of terrains and grass types. With a hydrostatic transmission, users can enjoy seamless acceleration and deceleration, allowing for precise control during mowing and maneuvering around obstacles.

The 247.88045 is equipped with a 54-inch cutting deck, which provides a wide mowing path, reducing the time and effort required to cover large lawns. The deck features a dual-blade system, ensuring a clean and even cut, which is essential for maintaining a healthy lawn. Additionally, the cutting height is adjustable, allowing users to choose the perfect height for their grass type and seasonal needs.

Ergonomics are also a major consideration in the design of the Craftsman 247.88045. The seat is comfortable and adjustable, accommodating various driver heights, while the steering wheel is positioned for ease of access and control. The tractor is fitted with a fuel gauge and an easy-to-reach dashboard, which provides essential information at a glance, enhancing the user experience.

Durability and reliability are key characteristics of the Craftsman brand, and the 247.88045 is no exception. Constructed with high-quality materials, this lawn tractor is designed to withstand the rigors of regular use. The robust frame and heavy-duty tires offer stability and traction, making it suitable for uneven terrain and different weather conditions.

For added functionality, the Craftsman 247.88045 can be equipped with various attachments, such as a lawn sweeper or snow plow, making it a multi-season tool for homeowners. Its versatility transforms lawn maintenance into a more manageable task, enabling users to extend the tractor's usability beyond just mowing.

In summary, the Craftsman 247.88045 lawn tractor is a powerful, user-friendly machine that combines advanced technology, ergonomic design, and durable construction. Whether you're maintaining a small yard or a larger landscape, this lawn tractor is a reliable partner for achieving a pristine lawn.
Top Page Image Contents