Craftsman 247.88045 manual OFF-SEASON Storage, Preparing Engine, Preparing Snow Thrower

Page 22

OFF-SEASON STORAGE

If the snow thrower will not be used for 30 days or longer, or if it is the end of the snow season when the last possibility of snow is gone, the equipment needs to be stored properly. Follow storage instructions below to ensure top performance from the snow thrower for many more years.

Preparing Engine

Short-Term Storage

It is important to prevent gum deposits from forming in essential fuel system parts of the engine such as the carburetor, fuel filter, fuel hose, or tank during short-term storage (15-30 days). To prevent this, treat the fuel system using a fuel stabilizer.

Fuel stabilizer (such as STA-BIL™ or ULTRA-FRESH™) is an accept- able alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow it to reach the carbure- tor.

Preparing Snow Thrower

•When storing the snow thrower in an unventilated or metal stor- age shed, care should be taken to rustproof the equipment. Using a light oil or silicone, coat the equipment, especially any chains, springs, bearings and cables.

•Remove all dirt from exterior of engine and equipment.

•Follow lubrication recommendations.

•Store equipment in a clean, dry area.

WARNING

Never store snow thrower with fuel in tank indoors or in poorly venti- lated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance.

CAUTION

Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

Long-Term Storage

To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer.

WARNING

Fuel left in engine during warm weather deteriorates and will cause serious starting problems.

1.Run the engine until the fuel tank is empty and it stops due to lack of fuel. Do not attempt to pour fuel from the engine.

WARNING

Never use engine or carburetor cleaning products in the fuel tank or permanent damage may occur.

2.Remove the spark plug and pour one (1) ounce of engine oil through the spark plug hole into the cylinder. Cover spark plug hole with a rag and crank the engine several times to distribute the oil. Replace spark plug.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Form no 28/2007Warranty Statement Table of ContentsProduct Specifications Model Number Training Safety InstructionsPreparation Maintenance & Storage OperationSafety Labels USE CLEAN-OUT Tool to Unclog Discharge ChuteRemoving From Crate AssemblyAssembly Place the shift lever in the F6 positionSet-Up Chute Clean-Out ToolDrift Cutters Skid Shoes AdjustmentsTire Pressure ControlAdjusting Drive and Auger Controls Testing Auger Drive ControlTesting Drive Control & Shift Lever Retighten nuts and bolts securelyOperation Skid Shoes Chute AssemblyThrottle Control Recoil Starter HandleBefore Starting Engine Clean-Out ToolStarting The Engine To Engage Drive Replacing Shear PinsStopping The Engine To Engage AugersChanging Engine Oil Service and MaintenanceChecking Engine Oil Oil FIll Oil DrainLubrication Shift Rod Shave Plate and Skid ShoesShave Plate Chute ControlChute Bracket Belt replacementDrive Control Auger ControlHousing forward and pulling up the handles Auger Belt ReplacementLoosen the bolt shown in securing the belt keeper Drive Belt Replacement If also replacing the drive belt, proceed to the Drive BeltChanging Friction Wheel Belleville Washer Slide Hex Shaft Out Right SideGas in the tank † Under heavy load or in high temperatures Each Use Engine oil level CheckPreparing Snow Thrower OFF-SEASON StoragePreparing Engine Short-Term StorageTroubleshooting Parts List Craftsman Snow Thrower ModelHousing, Auger 684-04151 39 -04020 Spacer, 1.004 x 1.375 x 721-0146Parts List 61 -0199A Bumper, Rubber 784-5619B 41 -0963 Connector, Shift Rod79 -04220 Harness 80 -1364 Housing 81 -0225 Grommet 77 -1658 Lamp 725-166979 8 1478 61 49 3173 37 -0104 Pin, Internal Cotter From previous Craftsman Engine Model OH358SA-223828 For Snow Thrower Model Oil Drain Extension Not Available 37083 Cylinder Incl , 20, 72Dowel Pin 30969 Extension Cap, 1/4-18 NPT 28277 Flat Washer37085 Intake Pipe 35079A Key Switch Bracket Incl a28425 35691 Governor Link400 36947B 351 32180C Primer Line 355Packaged 740053B MarkedPage Sears Emission Control Defects Warranty Coverage This page applicable in the U.S.A. and Canada onlyPage Repair Protection Agreement Especificaciones DEL Producto ÍndiceDeclaración DE Garantía Número DE ModeloCapacitación Instrucciones DE SeguridadPreparativos Operación Mantenimiento y almacenamientoExtracción de la unidad del cajón Coloque la palanca de cambios en posición F6Montaje MontajeHerramienta de limpieza del canal ConfiguraciónCortadores de desplazamiento de nieve Presión de los neumáticos AjustesZapatas antideslizantes Prueba del control de la transmisión de la barrena Prueba de control de transmisión y palanca de cambiosVea Ajuste de transmisión y controles de barrena Llave de encendido Palanca de cambiosOperación FaroBotón del arrancador eléctrico Control del estranguladorManija del arrancador de retroceso Salida del arrancador eléctricoHerramienta de limpieza Control del canal de 2 direccionesControl direccional del canal Antes de encender el motorProcedimiento para engranar las barrenas Detención del motorProcedimiento para engranar la transmisión Arrancador de retrocesoControl del aceite del motor Servicio Y MantenimientoMantenimiento de Motor Cambio de aceite del motorLubricación Varilla de cambio Placa de raspado y zapatas antideslizantesPlaca de raspado Control del canalSoporte del canal Cambio de correaControl de la transmisión Control de la barrenaNota Asegúrese que la posición del regatón en la vara de Reemplazo de la correa de la barrenaDel motor. Vea la Figura Holgazán de taladro es mantenidaMotor e instale nuevamente la cubierta de la correa Reemplazo de la correa de transmisiónBarrena al eje de entrada Ranura de polea AdaptadorCambio de la rueda de fricción Eje hexagonalDeslice el separador sobre el extremo del eje hexagonal Cada Uso Nivel del aceite de motor Comprobar Tanque † Bajo carga pesada o en temperaturas altasPreparación de la máquina quitanieve Almacenamiento Fuera DE TemporadaPreparación del motor Almacenaje a Corto plazoSolución DE Problemas Esta página se aplica sólo en EE.UU. y Canadá Piezas con garantíaMotor certificado Acuerdo DE Protección Para Reparaciones Get it fixed, at your home or ours

247.88045 specifications

The Craftsman 247.88045 is a versatile lawn tractor designed to simplify lawn care for homeowners who seek both efficiency and ease of use. This powerful machine stands out with its robust features and technologically advanced design, catering to various landscaping needs.

One of the key features of the Craftsman 247.88045 is its powerful 24 horsepower Briggs & Stratton engine. This reliable engine ensures smooth operation and ample power to tackle a variety of terrains and grass types. With a hydrostatic transmission, users can enjoy seamless acceleration and deceleration, allowing for precise control during mowing and maneuvering around obstacles.

The 247.88045 is equipped with a 54-inch cutting deck, which provides a wide mowing path, reducing the time and effort required to cover large lawns. The deck features a dual-blade system, ensuring a clean and even cut, which is essential for maintaining a healthy lawn. Additionally, the cutting height is adjustable, allowing users to choose the perfect height for their grass type and seasonal needs.

Ergonomics are also a major consideration in the design of the Craftsman 247.88045. The seat is comfortable and adjustable, accommodating various driver heights, while the steering wheel is positioned for ease of access and control. The tractor is fitted with a fuel gauge and an easy-to-reach dashboard, which provides essential information at a glance, enhancing the user experience.

Durability and reliability are key characteristics of the Craftsman brand, and the 247.88045 is no exception. Constructed with high-quality materials, this lawn tractor is designed to withstand the rigors of regular use. The robust frame and heavy-duty tires offer stability and traction, making it suitable for uneven terrain and different weather conditions.

For added functionality, the Craftsman 247.88045 can be equipped with various attachments, such as a lawn sweeper or snow plow, making it a multi-season tool for homeowners. Its versatility transforms lawn maintenance into a more manageable task, enabling users to extend the tractor's usability beyond just mowing.

In summary, the Craftsman 247.88045 lawn tractor is a powerful, user-friendly machine that combines advanced technology, ergonomic design, and durable construction. Whether you're maintaining a small yard or a larger landscape, this lawn tractor is a reliable partner for achieving a pristine lawn.
Top Page Image Contents