Craftsman 247.88045 manual Each Use Engine oil level Check

Page 21

SERVICE AND MAINTENANCE

9.Reposition the friction wheel assembly in the snow thrower frame. Insert the pin from the shift arm assembly into the friction wheel assembly and hold assembly in position. Refer to Figure 33.

10.Slide the hex shaft through the right side of the frame toward the left side and through the friction wheel assembly.

11.After making certain that the chain is on both the large and the small sprocket, align the hex shaft with the hex hub of the small sprocket, and slide the shaft through the sprocket.

NOTE: If the sprocket fell from the snow thrower while removing the hex shaft, place the sprocket on the chain. Realign the sprocket on the chain with the hex hub facing the right side of unit. Position the hex hub of the sprocket toward the friction wheel when sliding the sprocket on to the hex shaft.

12.Slide the spacer onto the end of the hex shaft.

13.Align the bearing on the right end of the hex shaft with the hole in the right side of the frame, then push the hex shaft to the left into position in the frame.

14.Slide the bearing onto the left end of the hex shaft and press into the hole on the left side the frame.

15.Place the belleville washer (rounded side toward head) onto the hex screw removed earlier, and insert the screw into the threaded hole of the hex shaft.

16.Gradually tighten the hex screw to fully seat the bearings in each side of the frame and to secure the hex shaft.

Figure 33

17.Position the frame cover on the bottom of the frame and secure with the self-tapping screws. Pivot the snow thrower down to it normal operating position.

NOTE: If you placed plastic film under the gas cap, be certain to remove it.

MAINTENANCE SCHEDULE

WARNING

Before performing any type of maintenance/service, disengage all controls and stop the engine. Wait until all moving parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting. Always wear safety glasses during operation or while performing any adjustments or repairs.

Follow the maintenance schedule given below. This chart describes service guidelines only. Use the Service Log column to keep track of completed maintenance tasks. To locate the nearest Sears Service

Center or to schedule service, simply contact Sears at 1-800-4-MY-HOME®.

Interval

 

Item

 

Service

Service Log

Each Use

1.

Engine oil level

1.

Check

 

 

2.

Loose or missing hardware

2.

Tighten or replace

 

 

3.

Unit and engine.

3.

Clean

 

 

 

 

 

 

 

1st 5 - 8 hours

1.

Engine oil

1.

Change

 

 

 

 

 

 

 

25 hours

1.

Engine oil†

1.

Change

 

 

2.

Air cleaner

2.

Clean or replace

 

 

3.

Control linkages and pivots

3.

Lube with light oil

 

 

 

 

 

 

 

50 hours

1.

Engine oil

1.

Change

 

 

 

 

 

 

 

Annually or 100 hours

1.

Spark plug

1.

Clean, replace, re-gap

 

 

 

 

 

 

 

Before Storage

1.

Fuel system

1.

Run engine until it stops from lack of

 

 

 

 

 

fuel or add a gasoline additive to the

 

 

 

 

 

gas in the tank.

 

 

 

 

 

 

† Under heavy load or in high temperatures

 

 

 

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 28/2007 Form noTable of Contents Warranty StatementProduct Specifications Model Number Safety Instructions TrainingPreparation Operation Maintenance & StorageUSE CLEAN-OUT Tool to Unclog Discharge Chute Safety LabelsAssembly AssemblyRemoving From Crate Place the shift lever in the F6 positionChute Clean-Out Tool Set-UpDrift Cutters Tire Pressure AdjustmentsSkid Shoes ControlTesting Drive Control & Shift Lever Testing Auger Drive ControlAdjusting Drive and Auger Controls Retighten nuts and bolts securelyOperation Throttle Control Chute AssemblySkid Shoes Recoil Starter HandleClean-Out Tool Before Starting EngineStarting The Engine Stopping The Engine Replacing Shear PinsTo Engage Drive To Engage AugersChecking Engine Oil Service and MaintenanceChanging Engine Oil Oil FIll Oil DrainLubrication Shave Plate Shave Plate and Skid ShoesShift Rod Chute ControlDrive Control Belt replacementChute Bracket Auger ControlAuger Belt Replacement Housing forward and pulling up the handlesLoosen the bolt shown in securing the belt keeper If also replacing the drive belt, proceed to the Drive Belt Drive Belt ReplacementBelleville Washer Slide Hex Shaft Out Right Side Changing Friction WheelEach Use Engine oil level Check Gas in the tank † Under heavy load or in high temperaturesPreparing Engine OFF-SEASON StoragePreparing Snow Thrower Short-Term StorageTroubleshooting Craftsman Snow Thrower Model Parts List39 -04020 Spacer, 1.004 x 1.375 x 721-0146 Housing, Auger 684-04151Parts List 79 -04220 Harness 80 -1364 Housing 81 -0225 Grommet 41 -0963 Connector, Shift Rod61 -0199A Bumper, Rubber 784-5619B 77 -1658 Lamp 725-166979 8 1478 61 49 3173 37 -0104 Pin, Internal Cotter From previous Craftsman Engine Model OH358SA-223828 For Snow Thrower Model Dowel Pin 37083 Cylinder Incl , 20, 72Oil Drain Extension Not Available 30969 Extension Cap, 1/4-18 NPT 28277 Flat Washer28425 35079A Key Switch Bracket Incl a37085 Intake Pipe 35691 Governor LinkPackaged 740053B 351 32180C Primer Line 355400 36947B MarkedPage This page applicable in the U.S.A. and Canada only Sears Emission Control Defects Warranty CoveragePage Repair Protection Agreement Declaración DE Garantía ÍndiceEspecificaciones DEL Producto Número DE ModeloInstrucciones DE Seguridad CapacitaciónPreparativos Mantenimiento y almacenamiento OperaciónMontaje Coloque la palanca de cambios en posición F6Extracción de la unidad del cajón MontajeConfiguración Herramienta de limpieza del canalCortadores de desplazamiento de nieve Ajustes Presión de los neumáticosZapatas antideslizantes Prueba de control de transmisión y palanca de cambios Prueba del control de la transmisión de la barrenaVea Ajuste de transmisión y controles de barrena Operación Palanca de cambiosLlave de encendido FaroManija del arrancador de retroceso Control del estranguladorBotón del arrancador eléctrico Salida del arrancador eléctricoControl direccional del canal Control del canal de 2 direccionesHerramienta de limpieza Antes de encender el motorProcedimiento para engranar la transmisión Detención del motorProcedimiento para engranar las barrenas Arrancador de retrocesoMantenimiento de Motor Servicio Y MantenimientoControl del aceite del motor Cambio de aceite del motorLubricación Placa de raspado Placa de raspado y zapatas antideslizantesVarilla de cambio Control del canalControl de la transmisión Cambio de correaSoporte del canal Control de la barrenaDel motor. Vea la Figura Reemplazo de la correa de la barrenaNota Asegúrese que la posición del regatón en la vara de Holgazán de taladro es mantenidaBarrena al eje de entrada Reemplazo de la correa de transmisiónMotor e instale nuevamente la cubierta de la correa Ranura de polea AdaptadorEje hexagonal Cambio de la rueda de fricciónDeslice el separador sobre el extremo del eje hexagonal Tanque † Bajo carga pesada o en temperaturas altas Cada Uso Nivel del aceite de motor ComprobarPreparación del motor Almacenamiento Fuera DE TemporadaPreparación de la máquina quitanieve Almacenaje a Corto plazoSolución DE Problemas Piezas con garantía Esta página se aplica sólo en EE.UU. y CanadáMotor certificado Acuerdo DE Protección Para Reparaciones Get it fixed, at your home or ours

247.88045 specifications

The Craftsman 247.88045 is a versatile lawn tractor designed to simplify lawn care for homeowners who seek both efficiency and ease of use. This powerful machine stands out with its robust features and technologically advanced design, catering to various landscaping needs.

One of the key features of the Craftsman 247.88045 is its powerful 24 horsepower Briggs & Stratton engine. This reliable engine ensures smooth operation and ample power to tackle a variety of terrains and grass types. With a hydrostatic transmission, users can enjoy seamless acceleration and deceleration, allowing for precise control during mowing and maneuvering around obstacles.

The 247.88045 is equipped with a 54-inch cutting deck, which provides a wide mowing path, reducing the time and effort required to cover large lawns. The deck features a dual-blade system, ensuring a clean and even cut, which is essential for maintaining a healthy lawn. Additionally, the cutting height is adjustable, allowing users to choose the perfect height for their grass type and seasonal needs.

Ergonomics are also a major consideration in the design of the Craftsman 247.88045. The seat is comfortable and adjustable, accommodating various driver heights, while the steering wheel is positioned for ease of access and control. The tractor is fitted with a fuel gauge and an easy-to-reach dashboard, which provides essential information at a glance, enhancing the user experience.

Durability and reliability are key characteristics of the Craftsman brand, and the 247.88045 is no exception. Constructed with high-quality materials, this lawn tractor is designed to withstand the rigors of regular use. The robust frame and heavy-duty tires offer stability and traction, making it suitable for uneven terrain and different weather conditions.

For added functionality, the Craftsman 247.88045 can be equipped with various attachments, such as a lawn sweeper or snow plow, making it a multi-season tool for homeowners. Its versatility transforms lawn maintenance into a more manageable task, enabling users to extend the tractor's usability beyond just mowing.

In summary, the Craftsman 247.88045 lawn tractor is a powerful, user-friendly machine that combines advanced technology, ergonomic design, and durable construction. Whether you're maintaining a small yard or a larger landscape, this lawn tractor is a reliable partner for achieving a pristine lawn.
Top Page Image Contents