Craftsman 247.88045 manual Clean-Out Tool, Before Starting Engine, Starting The Engine

Page 12

OPERATION

Clean-Out Tool

WARNING

Never use your hands to clear a clogged chute assembly. Shut off engine and remain behind handles until all moving parts have stopped before unclogging.

The chute clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. Should snow and ice become lodged in the chute assembly during operation, proceed as follows to safely clean the chute assembly and chute opening:

1.Release both the Auger Control and the Drive Control.

2.Stop the engine by removing the ignition key.

3.Remove the clean-out tool from the clip which secures it to the rear of the auger housing.

4.Use the shovel-shaped end of the clean-out tool to dislodge and scoop any snow and ice which has formed in and near the chute assembly.

5.Refasten the clean-out tool to the mounting clip on the rear of the auger housing, reinsert the ignition key and start the snow thrower’s engine.

6.While standing in the operator’s position (behind the snow thrower), engage the auger control for a few seconds to clear any remaining snow and ice from the chute assembly.

Before Starting Engine

WARNING

Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.

Oil

The unit was shipped with oil in the engine. Check oil level before each operation to ensure adequate oil in the engine. For further instructions, refer to the steps on page 16.

1.Remove the dipstick from the oil fill.

2.Check and make sure that the level of oil is up to the FULL mark on the dipstick.

3.If the oil level is not up to FULL, pour fresh motor oil (5W-30, with a minimum classification of SL/SJ) slowly through the opening. Replace oil fill dipstick and check oil level again.

Gasoline

WARNING

Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.

•Store gasoline in a clean, approved container and keep the cap in place on the container.

•Make sure that the container from which you pour the gasoline is clean and free from rust or other foreign particles.

NOTE: A plastic dust cap may be found inside the fuel fill opening. Remove and discard, if present.

•Always fill the fuel tank outdoors and use a funnel or spout to prevent spilling.

•Fill fuel tank with clean, fresh, unleaded gasoline.

•Never fill the fuel tank completely. Fill the tank to within 1/2” from the top to provide space for expansion of fuel.

•Make sure to wipe off any spilled fuel before starting the engine.

Starting The Engine

1.Attach spark plug wire to spark plug. Make certain the metal loop on the end of the spark plug wire (inside the rubber boot) is fastened securely over the metal tip on the spark plug.

2.Make certain both the auger control and drive control are in the disengaged (released) position.

3. Move throttle control up to FAST position. Insert ignition key into slot. Make sure it snaps into place. Do not attempt to turn the key.

NOTE: The engine cannot start without the key is fully inserted into the ignition switch.

Electric Starter

Determine that your home’s wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain.

WARNING

The optional electric starter is equipped with a grounded three-wire power cord and plug, and is designed to operate on 120 volt AC household current. It must be used with a properly grounded three- prong receptacle at all times to avoid the possibility of electric shock. Follow all instructions carefully prior to operating the electric starter.

If you have a grounded three-prong receptacle, proceed as follows:

1.Plug the extension cord into the outlet located on the engine’s surface. Plug the other end of extension cord into a three-prong 120-volt, grounded, AC outlet in a well-ventilated area.

2. Rotate choke control to FULL

 

choke position (for a cold

engine start).

 

 

NOTE: If the engine is already warm, place choke control in the OFF

position instead of FULL .

3.Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing.

NOTE: DO NOT use primer to restart a warm engine after a short shutdown.

4.Push starter button to start engine.

NOTE: Do not hold the button down for longer than seven (7) seconds at a time. Doing so may damage your engine’s electric starter.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Form no 28/2007Table of Contents Warranty StatementProduct Specifications Model Number Safety Instructions TrainingPreparation Maintenance & Storage OperationSafety Labels USE CLEAN-OUT Tool to Unclog Discharge ChuteAssembly AssemblyRemoving From Crate Place the shift lever in the F6 positionChute Clean-Out Tool Set-UpDrift Cutters Adjustments Tire PressureSkid Shoes ControlTesting Auger Drive Control Testing Drive Control & Shift LeverAdjusting Drive and Auger Controls Retighten nuts and bolts securelyOperation Chute Assembly Throttle ControlSkid Shoes Recoil Starter HandleClean-Out Tool Before Starting EngineStarting The Engine Replacing Shear Pins Stopping The EngineTo Engage Drive To Engage AugersService and Maintenance Checking Engine OilChanging Engine Oil Oil FIll Oil DrainLubrication Shave Plate and Skid Shoes Shave PlateShift Rod Chute ControlBelt replacement Drive ControlChute Bracket Auger ControlAuger Belt Replacement Housing forward and pulling up the handlesLoosen the bolt shown in securing the belt keeper Drive Belt Replacement If also replacing the drive belt, proceed to the Drive BeltChanging Friction Wheel Belleville Washer Slide Hex Shaft Out Right SideGas in the tank † Under heavy load or in high temperatures Each Use Engine oil level CheckOFF-SEASON Storage Preparing EnginePreparing Snow Thrower Short-Term StorageTroubleshooting Parts List Craftsman Snow Thrower ModelHousing, Auger 684-04151 39 -04020 Spacer, 1.004 x 1.375 x 721-0146Parts List 41 -0963 Connector, Shift Rod 79 -04220 Harness 80 -1364 Housing 81 -0225 Grommet61 -0199A Bumper, Rubber 784-5619B 77 -1658 Lamp 725-166979 8 1478 61 49 3173 37 -0104 Pin, Internal Cotter From previous Craftsman Engine Model OH358SA-223828 For Snow Thrower Model 37083 Cylinder Incl , 20, 72 Dowel PinOil Drain Extension Not Available 30969 Extension Cap, 1/4-18 NPT 28277 Flat Washer35079A Key Switch Bracket Incl a 2842537085 Intake Pipe 35691 Governor Link351 32180C Primer Line 355 Packaged 740053B400 36947B MarkedPage Sears Emission Control Defects Warranty Coverage This page applicable in the U.S.A. and Canada onlyPage Repair Protection Agreement Índice Declaración DE GarantíaEspecificaciones DEL Producto Número DE ModeloInstrucciones DE Seguridad CapacitaciónPreparativos Operación Mantenimiento y almacenamientoColoque la palanca de cambios en posición F6 MontajeExtracción de la unidad del cajón MontajeConfiguración Herramienta de limpieza del canalCortadores de desplazamiento de nieve Ajustes Presión de los neumáticosZapatas antideslizantes Prueba de control de transmisión y palanca de cambios Prueba del control de la transmisión de la barrenaVea Ajuste de transmisión y controles de barrena Palanca de cambios OperaciónLlave de encendido FaroControl del estrangulador Manija del arrancador de retrocesoBotón del arrancador eléctrico Salida del arrancador eléctricoControl del canal de 2 direcciones Control direccional del canalHerramienta de limpieza Antes de encender el motorDetención del motor Procedimiento para engranar la transmisiónProcedimiento para engranar las barrenas Arrancador de retrocesoServicio Y Mantenimiento Mantenimiento de MotorControl del aceite del motor Cambio de aceite del motorLubricación Placa de raspado y zapatas antideslizantes Placa de raspadoVarilla de cambio Control del canalCambio de correa Control de la transmisiónSoporte del canal Control de la barrenaReemplazo de la correa de la barrena Del motor. Vea la FiguraNota Asegúrese que la posición del regatón en la vara de Holgazán de taladro es mantenidaReemplazo de la correa de transmisión Barrena al eje de entradaMotor e instale nuevamente la cubierta de la correa Ranura de polea AdaptadorCambio de la rueda de fricción Eje hexagonalDeslice el separador sobre el extremo del eje hexagonal Cada Uso Nivel del aceite de motor Comprobar Tanque † Bajo carga pesada o en temperaturas altasAlmacenamiento Fuera DE Temporada Preparación del motorPreparación de la máquina quitanieve Almacenaje a Corto plazoSolución DE Problemas Esta página se aplica sólo en EE.UU. y Canadá Piezas con garantíaMotor certificado Acuerdo DE Protección Para Reparaciones Get it fixed, at your home or ours

247.88045 specifications

The Craftsman 247.88045 is a versatile lawn tractor designed to simplify lawn care for homeowners who seek both efficiency and ease of use. This powerful machine stands out with its robust features and technologically advanced design, catering to various landscaping needs.

One of the key features of the Craftsman 247.88045 is its powerful 24 horsepower Briggs & Stratton engine. This reliable engine ensures smooth operation and ample power to tackle a variety of terrains and grass types. With a hydrostatic transmission, users can enjoy seamless acceleration and deceleration, allowing for precise control during mowing and maneuvering around obstacles.

The 247.88045 is equipped with a 54-inch cutting deck, which provides a wide mowing path, reducing the time and effort required to cover large lawns. The deck features a dual-blade system, ensuring a clean and even cut, which is essential for maintaining a healthy lawn. Additionally, the cutting height is adjustable, allowing users to choose the perfect height for their grass type and seasonal needs.

Ergonomics are also a major consideration in the design of the Craftsman 247.88045. The seat is comfortable and adjustable, accommodating various driver heights, while the steering wheel is positioned for ease of access and control. The tractor is fitted with a fuel gauge and an easy-to-reach dashboard, which provides essential information at a glance, enhancing the user experience.

Durability and reliability are key characteristics of the Craftsman brand, and the 247.88045 is no exception. Constructed with high-quality materials, this lawn tractor is designed to withstand the rigors of regular use. The robust frame and heavy-duty tires offer stability and traction, making it suitable for uneven terrain and different weather conditions.

For added functionality, the Craftsman 247.88045 can be equipped with various attachments, such as a lawn sweeper or snow plow, making it a multi-season tool for homeowners. Its versatility transforms lawn maintenance into a more manageable task, enabling users to extend the tractor's usability beyond just mowing.

In summary, the Craftsman 247.88045 lawn tractor is a powerful, user-friendly machine that combines advanced technology, ergonomic design, and durable construction. Whether you're maintaining a small yard or a larger landscape, this lawn tractor is a reliable partner for achieving a pristine lawn.
Top Page Image Contents