Craftsman 247.88045 Auger Belt Replacement, Loosen the bolt shown in securing the belt keeper

Page 18

SERVICE AND MAINTENANCE

2.Remove the plastic belt cover, located near the engine, by remov- ing the three self-tapping screws that secure it. See Figure 23.

3. Loosen the bolt shown in Figure 24 securing the belt keeper

Remove

bracket and remove the other bolt. Push the belt keeper and

 

bracket up off the engine pulley. See Figure 24.

 

Auger Belt Replacement

1. Remove the hairpin clip and flat washer from the ferrule in order

to disconnect the auger idler rod from the brake bracket assem-

bly. See Figure 25.Loosen NOTE: Make sure that the location of the ferrule on the auger

idler rod is maintained.

2.Slip the auger control belt (the front belt) off the engine pulley.

3.Pull the brake bracket assembly towards the cable guide roller and unhook the auger cable “Z” fitting. See Figure 26.

4. From both sides of the the frame assembly, use a 1/2” wrench to

Figure 24

remove the three hex tap screws securing the frame to the auger

 

housing assembly. Refer to Figure 22 on previous page.

 

NOTE: Do not remove the lower hex flange lock nut on each side.

 

5.Place a block of wood underneath the auger housing as shown in Figure 27 and separate auger housing from the frame by tilting the

housing forward and pulling up the handles.

6. Block the impeller with a piece of wood to prevent it from spinning and use a 1/2” wrench to remove the hex screw and flat washer from the center of the pulley on the auger housing. See Figure 28.

7.Lift the brake bracket assembly out of the pulley groove and slide the pulley assembly off the posts of the auger pulley adapter to remove the old belt. Refer to Figure 28.

Figure 25

Figure 23

Figure 26

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Form no 28/2007Table of Contents Warranty StatementProduct Specifications Model Number Safety Instructions TrainingPreparation Maintenance & Storage OperationSafety Labels USE CLEAN-OUT Tool to Unclog Discharge ChuteRemoving From Crate AssemblyAssembly Place the shift lever in the F6 positionChute Clean-Out Tool Set-UpDrift Cutters Skid Shoes AdjustmentsTire Pressure ControlAdjusting Drive and Auger Controls Testing Auger Drive ControlTesting Drive Control & Shift Lever Retighten nuts and bolts securelyOperation Skid Shoes Chute AssemblyThrottle Control Recoil Starter HandleClean-Out Tool Before Starting EngineStarting The Engine To Engage Drive Replacing Shear PinsStopping The Engine To Engage AugersChanging Engine Oil Service and MaintenanceChecking Engine Oil Oil FIll Oil DrainLubrication Shift Rod Shave Plate and Skid ShoesShave Plate Chute ControlChute Bracket Belt replacementDrive Control Auger ControlAuger Belt Replacement Housing forward and pulling up the handlesLoosen the bolt shown in securing the belt keeper Drive Belt Replacement If also replacing the drive belt, proceed to the Drive BeltChanging Friction Wheel Belleville Washer Slide Hex Shaft Out Right SideGas in the tank † Under heavy load or in high temperatures Each Use Engine oil level CheckPreparing Snow Thrower OFF-SEASON StoragePreparing Engine Short-Term StorageTroubleshooting Parts List Craftsman Snow Thrower ModelHousing, Auger 684-04151 39 -04020 Spacer, 1.004 x 1.375 x 721-0146Parts List 61 -0199A Bumper, Rubber 784-5619B 41 -0963 Connector, Shift Rod79 -04220 Harness 80 -1364 Housing 81 -0225 Grommet 77 -1658 Lamp 725-166979 8 1478 61 49 3173 37 -0104 Pin, Internal Cotter From previous Craftsman Engine Model OH358SA-223828 For Snow Thrower Model Oil Drain Extension Not Available 37083 Cylinder Incl , 20, 72Dowel Pin 30969 Extension Cap, 1/4-18 NPT 28277 Flat Washer37085 Intake Pipe 35079A Key Switch Bracket Incl a28425 35691 Governor Link400 36947B 351 32180C Primer Line 355Packaged 740053B MarkedPage Sears Emission Control Defects Warranty Coverage This page applicable in the U.S.A. and Canada onlyPage Repair Protection Agreement Especificaciones DEL Producto ÍndiceDeclaración DE Garantía Número DE ModeloInstrucciones DE Seguridad CapacitaciónPreparativos Operación Mantenimiento y almacenamientoExtracción de la unidad del cajón Coloque la palanca de cambios en posición F6Montaje MontajeConfiguración Herramienta de limpieza del canalCortadores de desplazamiento de nieve Ajustes Presión de los neumáticosZapatas antideslizantes Prueba de control de transmisión y palanca de cambios Prueba del control de la transmisión de la barrenaVea Ajuste de transmisión y controles de barrena Llave de encendido Palanca de cambiosOperación FaroBotón del arrancador eléctrico Control del estranguladorManija del arrancador de retroceso Salida del arrancador eléctricoHerramienta de limpieza Control del canal de 2 direccionesControl direccional del canal Antes de encender el motorProcedimiento para engranar las barrenas Detención del motorProcedimiento para engranar la transmisión Arrancador de retrocesoControl del aceite del motor Servicio Y MantenimientoMantenimiento de Motor Cambio de aceite del motorLubricación Varilla de cambio Placa de raspado y zapatas antideslizantesPlaca de raspado Control del canalSoporte del canal Cambio de correaControl de la transmisión Control de la barrenaNota Asegúrese que la posición del regatón en la vara de Reemplazo de la correa de la barrenaDel motor. Vea la Figura Holgazán de taladro es mantenidaMotor e instale nuevamente la cubierta de la correa Reemplazo de la correa de transmisiónBarrena al eje de entrada Ranura de polea AdaptadorCambio de la rueda de fricción Eje hexagonalDeslice el separador sobre el extremo del eje hexagonal Cada Uso Nivel del aceite de motor Comprobar Tanque † Bajo carga pesada o en temperaturas altasPreparación de la máquina quitanieve Almacenamiento Fuera DE TemporadaPreparación del motor Almacenaje a Corto plazoSolución DE Problemas Esta página se aplica sólo en EE.UU. y Canadá Piezas con garantíaMotor certificado Acuerdo DE Protección Para Reparaciones Get it fixed, at your home or ours

247.88045 specifications

The Craftsman 247.88045 is a versatile lawn tractor designed to simplify lawn care for homeowners who seek both efficiency and ease of use. This powerful machine stands out with its robust features and technologically advanced design, catering to various landscaping needs.

One of the key features of the Craftsman 247.88045 is its powerful 24 horsepower Briggs & Stratton engine. This reliable engine ensures smooth operation and ample power to tackle a variety of terrains and grass types. With a hydrostatic transmission, users can enjoy seamless acceleration and deceleration, allowing for precise control during mowing and maneuvering around obstacles.

The 247.88045 is equipped with a 54-inch cutting deck, which provides a wide mowing path, reducing the time and effort required to cover large lawns. The deck features a dual-blade system, ensuring a clean and even cut, which is essential for maintaining a healthy lawn. Additionally, the cutting height is adjustable, allowing users to choose the perfect height for their grass type and seasonal needs.

Ergonomics are also a major consideration in the design of the Craftsman 247.88045. The seat is comfortable and adjustable, accommodating various driver heights, while the steering wheel is positioned for ease of access and control. The tractor is fitted with a fuel gauge and an easy-to-reach dashboard, which provides essential information at a glance, enhancing the user experience.

Durability and reliability are key characteristics of the Craftsman brand, and the 247.88045 is no exception. Constructed with high-quality materials, this lawn tractor is designed to withstand the rigors of regular use. The robust frame and heavy-duty tires offer stability and traction, making it suitable for uneven terrain and different weather conditions.

For added functionality, the Craftsman 247.88045 can be equipped with various attachments, such as a lawn sweeper or snow plow, making it a multi-season tool for homeowners. Its versatility transforms lawn maintenance into a more manageable task, enabling users to extend the tractor's usability beyond just mowing.

In summary, the Craftsman 247.88045 lawn tractor is a powerful, user-friendly machine that combines advanced technology, ergonomic design, and durable construction. Whether you're maintaining a small yard or a larger landscape, this lawn tractor is a reliable partner for achieving a pristine lawn.
Top Page Image Contents