Pre-Start, To Stop in AN Emergency | Ariens 932046

PRE-START

1. Frozen Impeller

IMPORTANT: Before starting engine, check impeller to be sure it is not frozen.

To check impeller:

1.With ignition key switch in “Stop” position, squeeze Attachment Clutch Lever to Engaged position.

2.Pull Recoil Starter Handle.

3.If Impeller is frozen, (cannot pull Starter Handle) move unit to a heated area and thaw to prevent possible damage.

2.Check Function of Clutches

If clutches do not engage or disengage properly, adjust or repair before operation (see Attachment Clutch/Brake Adjustment on page 21, Traction Drive Clutch Adjustment on page 23).

3. Check Axle Lock

Use the axle lock pins to lock or unlock the wheels. Lock both wheels to increase traction; unlock one wheel to allow for easier turning of the unit.

4. Check Runners

Check and adjust Runners (Runners on page 18). Allow 1/8 in. (3 mm) between scraper blade and hard, smooth surface(s). Allow 1-1/4 in. (30 mm) between scraper blade and uneven or gravel surfaces.

5. Check Engine Fuel & Crankcase Oil

WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding.

Check and add fuel if required. Check that the engine crankcase oil is full using dipstick. Refer to Engine Manual for detailed instructions.

TO STOP IN AN EMERGENCY

Immediately release both control levers to stop unit in an emergency. Stop engine, remove key and wait for all rotating parts to stop before leaving operator’s position.

STARTING AND SHUT OFF

WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. DO NOT attempt to start your unit at this time. Read entire Owner/Operator Manual and the Engine Manual first.

IMPORTANT: Allow unit and engine to adjust to the outdoor temperature before clearing snow. Before shut-off, run the attachment a few minutes to prevent impeller freeze-up.

NOTE: Try out each control without the engine running to see how it works and what it does.

Manual Start

1.Turn discharge chute straight ahead.

2.Make sure that the traction clutch and attachment drive clutch levers are fully disengaged.

3.Push Primer Bulb 2 or 3 times for cold engine.

NOTE: When temperature is below -15° F (-26° C) additional priming may be needed.

4.If engine is cold, apply choke. See Engine Manual for detailed instructions.

NOTE: A warm engine requires less choking than a cold engine.

5.Set throttle to proper starting position. (932046, 047, 048)

6.Turn on engine shut-off switch ("ON"). (932045)

7.Insert key into ignition switch and push into RUN position. DO NOT twist key after it is inserted.

8.Grasp starter handle and pull rope out slowly until it pulls harder. Let rope rewind slowly.

9.Pull rope with a rapid continuous full arm stroke. Let rope rewind slowly.

IMPORTANT: DO NOT let Starter Handle snap against Starter.

10.Repeat steps 7 and 8 until engine starts. (If engine does not start, refer to TROUBLESHOOTING on page 26.)

11.Adjust choke as needed.

12.Set throttle to Part Throttle or Slow position for adaptation to outside temperature or travel. Set throttle to Fast position for normal operation.

(932046, 047, 048)

Electric Start (120V)

1. Connect extension cord to starter.

IMPORTANT: Prevent damage to unit. Know voltage of your starter and only use matching outlets.

2.Plug extension into 120V 3-wire, grounded outlet.

3.Turn discharge chute straight ahead.

GB - 14

932045 - ST8524E, 932048 - ST5520, 932046 - ST724E, 932047 - ST5524E specifications

The Ariens brand has long been synonymous with quality and durability in outdoor power equipment, particularly in snow blowers. The models Ariens 932047 (ST5524E), 932046 (ST724E), 932048 (ST5520), and 932045 (ST8524E) each deliver exceptional performance designed to handle a variety of winter conditions.

The Ariens 932047 - ST5524E is particularly well-regarded for its efficient 24-inch clearing width, making it ideal for residential driveways and sidewalks. With a powerful 223cc engine, this model provides ample power to tackle heavy, wet snow. It features a 200-degree chute rotation, which allows for precise snow throwing, enabling users to direct snow exactly where it is needed. The easy-to-use controls make operation simple, even in the harshest weather.

Similarly, the 932046 - ST724E offers a wider clearing width of 24 inches as well, paired with a robust 254cc engine. This model excels in heavy snow conditions, thanks to its deep-set auger design that effortlessly breaks down tough snow layers. The adjustable skid shoes enhance stability and control, while the electric start feature provides convenient starting, even in the coldest temperatures.

The Ariens 932048 - ST5520 is a slightly more compact option, maintaining a 20-inch clearing width and featuring a reliable 223cc engine. This snow blower is perfect for those with tighter spaces to clear, like alleys or smaller driveways. Its lightweight construction makes it easy to maneuver, while still providing the power needed for effective snow removal. The intuitive controls and multiple speed settings provide flexibility for the user.

Lastly, the 932045 - ST8524E stands out with its impressive 28-inch clearing width, making quick work of large areas. The 306cc engine is among the most powerful in the lineup, allowing it to handle even the toughest snowfalls with ease. This model incorporates advanced features like an automatically adjustable auger and impeller, maximizing performance in various snow conditions.

All four models incorporate Ariens’ signature build quality, ensuring long-lasting performance and reliability. With features like reinforced steel construction, adjustable skid shoes, and user-friendly designs, these snow blowers are perfect for tackling winter’s toughest challenges.