Ariens 932045 - ST8524E manual Speed Selector Adjustment, Attachment Drive Belt Replacement

Page 19

DISCHARGE CHUTE (932045, 046, 047)

If chute does not stay in position while operating, tighten nut on carriage bolt at pivot point to increase tension on spring (Figure 19).

1, 2

OS0001

1, 2

1.Carriage Bolt

2.Spring

Figure 19

DS6730

SPEED SELECTOR ADJUSTMENT

To adjust (Figure 20):

1.Disconnect pivot pin from the speed selector arm. Save the hardware for reinstallation.

2.Place the speed selector lever in the fastest forward speed position.

3.Push the speed selector arm straight down towards the ground as far as it will go.

4.Thread the adjustment pivot pin up or down the shift rod until it aligns with the mating hole in the speed selector arm.

5.Connect the pivot pin to the speed selector arm with the hardware removed in step 1.

6.Check forward and reverse speeds.

a.Start unit.

b.Shift speed selector into the first forward speed.

c.Engage the traction clutch. Unit should move forward.

d.Stop unit.

e.Shift speed selector into the first reverse speed.

f.Engage the traction clutch. Unit should move backward.

g.Shut off unit.

7.Adjust pivot pin on the shift rod as needed so unit travels forward when speed selector lever is in first forward position and backward when speed selector is in first reverse position.

8.Connect the pivot pin to the speed selector arm with the hardware removed in step 1.

1

2

4

 

3

 

1. Shift Rod

 

2. Pivot Pin

 

3. Speed Selector Arm

 

4. Hair Pin

 

Figure 20

OS7230

 

OS7235

ATTACHMENT DRIVE BELT

REPLACEMENT

Remove Attachment Drive Belt

(Figures 21, 22 and 23)

1.Shut off engine, remove key, disconnect spark plug wire and allow unit to cool completely.

2.Remove two screws securing belt cover to unit and remove belt cover.

3.Remove spring pin from chute crank and separate (932045, 046, 047).

GB - 19

Image 19
Contents Sno-Thro Introduction Table of ContentsSafety Decals and Locations SafetyPersonal Safety Is Involved Become Alert Obey The Message Clogs or servicing Safety RulesPage Page Package Contents AssemblyAssembly Check Engine Crankcase Oil Install Discharge Chute CrankCheck Tire Pressure Check Auger Gearcase Oil932046, 047 Controls and Features932045 Primer Bulb OperationAttachment Clutch Right Hand Lever Speed Selector Throttle 932046, 047 Engine Shut-Off SwitchSnow Clean-Out Tool Figure Choke Control Knob 932046, 047 932045Filling Fuel Tank To Stop in AN Emergency PRE-STARTStarting and Shut OFF Shut Off Snow RemovalTraveling TransportMaintenance General Lubrication Change Engine OILCheck Tire Pressure Check Auger GearcaseShear Bolts Service and AdjustmentsScraper Blade RunnersAttachment Drive Belt Replacement Speed Selector AdjustmentRemove Attachment Drive Belt Replace Attachment Drive Belt Brake Adjustment belowAdjustment Traction Drive Belt ReplacementAttachment CLUTCH/BRAKE Attachment Clutch Lever In. 7 15,2 cm 17,8 cm Friction Disc Replacement Traction Drive Clutch AdjustmentRemove Friction Disc Replace Friction Disc Reinstall Friction DiscAccessories Service PartsStorage Selector Adjustment on TroubleshootingEngine SpecificationsAriens Limited Warranties Exceptions, Limitations, Exclusions

932045 - ST8524E, 932048 - ST5520, 932046 - ST724E, 932047 - ST5524E specifications

The Ariens brand has long been synonymous with quality and durability in outdoor power equipment, particularly in snow blowers. The models Ariens 932047 (ST5524E), 932046 (ST724E), 932048 (ST5520), and 932045 (ST8524E) each deliver exceptional performance designed to handle a variety of winter conditions.

The Ariens 932047 - ST5524E is particularly well-regarded for its efficient 24-inch clearing width, making it ideal for residential driveways and sidewalks. With a powerful 223cc engine, this model provides ample power to tackle heavy, wet snow. It features a 200-degree chute rotation, which allows for precise snow throwing, enabling users to direct snow exactly where it is needed. The easy-to-use controls make operation simple, even in the harshest weather.

Similarly, the 932046 - ST724E offers a wider clearing width of 24 inches as well, paired with a robust 254cc engine. This model excels in heavy snow conditions, thanks to its deep-set auger design that effortlessly breaks down tough snow layers. The adjustable skid shoes enhance stability and control, while the electric start feature provides convenient starting, even in the coldest temperatures.

The Ariens 932048 - ST5520 is a slightly more compact option, maintaining a 20-inch clearing width and featuring a reliable 223cc engine. This snow blower is perfect for those with tighter spaces to clear, like alleys or smaller driveways. Its lightweight construction makes it easy to maneuver, while still providing the power needed for effective snow removal. The intuitive controls and multiple speed settings provide flexibility for the user.

Lastly, the 932045 - ST8524E stands out with its impressive 28-inch clearing width, making quick work of large areas. The 306cc engine is among the most powerful in the lineup, allowing it to handle even the toughest snowfalls with ease. This model incorporates advanced features like an automatically adjustable auger and impeller, maximizing performance in various snow conditions.

All four models incorporate Ariens’ signature build quality, ensuring long-lasting performance and reliability. With features like reinforced steel construction, adjustable skid shoes, and user-friendly designs, these snow blowers are perfect for tackling winter’s toughest challenges.