Ariens 932046 - ST724E manual Service and Adjustments, Scraper Blade, Runners, Shear Bolts

Page 18

SERVICE AND ADJUSTMENTS

WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding.

SCRAPER BLADE

IMPORTANT: Damage to auger/impeller housing will result if blade wears down too far.

Scraper blade is adjustable to compensate for wear.

To adjust scraper blade:

1.Tip unit back onto handlebar, support housing and loosen nuts retaining blade.

2.Adjust runners to fully raised position (housing closest to ground).

3.Reposition scraper blade flush with runners and tighten lock nuts.

RUNNERS

Runners should be adjusted as conditions require (Figure 16).

1.Position unit on a hard, flat, smooth level surface.

2.Adjust runners by inserting a spacer of desired thickness under center of scraper blade, loosen runner hardware, slide runners to flat surface.

Allow 1/8 in. (3 mm) between scraper blade and hard smooth surfaces. Allow 1-1/4 in. (30 mm) between scraper blade and uneven or gravel surfaces. Retighten hardware.

NOTE: Keep housing level by adjusting runners equally.

2

1

1.Runner

2.Runner Hardware

OS0482

Figure 16

SHEAR BOLTS

IMPORTANT: Use only Ariens shear bolts for replacement. Use of any other type of shear bolt may result in severe damage to unit.

Occasionally a foreign object may enter the auger/impeller housing and jam the auger, breaking shear bolts (Figure 17) which secure the auger to the shaft. This allows auger to turn freely on the shaft preventing damage to gear drive.

2

1

 

 

2

 

1. Auger

 

2. Shear Bolts

 

Figure 17

For Replacement:

1.Align shear bolt holes in auger with shear bolt holes in the shaft.

2.Drive shear bolt through hole (if shear bolt was broken this will drive remaining part from shaft).

3.Secure shear bolt with nut.

DISCHARGE CHUTE DEFLECTOR

Deflector must stay in selected position while throwing snow.

To adjust, loosen then retighten hardware to desired deflector drag force (Figure 18).

Adjusting

Hardware

Discharge Chute

Deflector

Figure 18

OS1113

GB - 18

Image 18
Contents Sno-Thro Table of Contents IntroductionSafety Safety Decals and LocationsPersonal Safety Is Involved Become Alert Obey The Message Safety Rules Clogs or servicingPage Page Assembly Package ContentsAssembly Check Auger Gearcase Oil Install Discharge Chute CrankCheck Tire Pressure Check Engine Crankcase OilControls and Features 932046, 047932045 Operation Primer BulbAttachment Clutch Right Hand Lever Speed Selector Choke Control Knob 932046, 047 932045 Engine Shut-Off SwitchSnow Clean-Out Tool Figure Throttle 932046, 047Filling Fuel Tank PRE-START To Stop in AN EmergencyStarting and Shut OFF Transport Snow RemovalTraveling Shut OffMaintenance Check Auger Gearcase Change Engine OILCheck Tire Pressure General LubricationRunners Service and AdjustmentsScraper Blade Shear BoltsSpeed Selector Adjustment Attachment Drive Belt ReplacementRemove Attachment Drive Belt Brake Adjustment below Replace Attachment Drive BeltTraction Drive Belt Replacement AdjustmentAttachment CLUTCH/BRAKE Attachment Clutch Lever In. 7 15,2 cm 17,8 cm Traction Drive Clutch Adjustment Friction Disc ReplacementRemove Friction Disc Reinstall Friction Disc Replace Friction DiscService Parts AccessoriesStorage Troubleshooting Selector Adjustment onSpecifications EngineAriens Limited Warranties Exceptions, Limitations, Exclusions

932045 - ST8524E, 932048 - ST5520, 932046 - ST724E, 932047 - ST5524E specifications

The Ariens brand has long been synonymous with quality and durability in outdoor power equipment, particularly in snow blowers. The models Ariens 932047 (ST5524E), 932046 (ST724E), 932048 (ST5520), and 932045 (ST8524E) each deliver exceptional performance designed to handle a variety of winter conditions.

The Ariens 932047 - ST5524E is particularly well-regarded for its efficient 24-inch clearing width, making it ideal for residential driveways and sidewalks. With a powerful 223cc engine, this model provides ample power to tackle heavy, wet snow. It features a 200-degree chute rotation, which allows for precise snow throwing, enabling users to direct snow exactly where it is needed. The easy-to-use controls make operation simple, even in the harshest weather.

Similarly, the 932046 - ST724E offers a wider clearing width of 24 inches as well, paired with a robust 254cc engine. This model excels in heavy snow conditions, thanks to its deep-set auger design that effortlessly breaks down tough snow layers. The adjustable skid shoes enhance stability and control, while the electric start feature provides convenient starting, even in the coldest temperatures.

The Ariens 932048 - ST5520 is a slightly more compact option, maintaining a 20-inch clearing width and featuring a reliable 223cc engine. This snow blower is perfect for those with tighter spaces to clear, like alleys or smaller driveways. Its lightweight construction makes it easy to maneuver, while still providing the power needed for effective snow removal. The intuitive controls and multiple speed settings provide flexibility for the user.

Lastly, the 932045 - ST8524E stands out with its impressive 28-inch clearing width, making quick work of large areas. The 306cc engine is among the most powerful in the lineup, allowing it to handle even the toughest snowfalls with ease. This model incorporates advanced features like an automatically adjustable auger and impeller, maximizing performance in various snow conditions.

All four models incorporate Ariens’ signature build quality, ensuring long-lasting performance and reliability. With features like reinforced steel construction, adjustable skid shoes, and user-friendly designs, these snow blowers are perfect for tackling winter’s toughest challenges.