Ariens 932047 - ST5524E, 932048 - ST5520 manual Replace Friction Disc, Reinstall Friction Disc

Page 24

CAUTION: Before tipping unit, remove enough fuel so that no spills occur.

2.Tip the unit up onto front housing on a level surface.

3.Remove lockpins from wheel axles and remove wheels.

4.Remove two bolts from top of bottom cover.

5.Loosen two bottom screws and slide cover off.

6.Disconnect pivot pin from the speed selector arm. Save the hardware for reinstallation.

7.Carefully tap two roll pins out of center and right end of hex shaft.

8.Remove four nuts from bearing cap on left side of unit. Remove bearing and outside bearing cap.

9.Reinstall one nut to keep the inside bearing cap in place.

10.Remove bearing cap/bushing and washer from right side of unit.

11.Reinstall nuts on screws through side frame to keep screws in place.

12.Slide friction disc assembly and hex shaft to the right until the left end of shaft is clear of left bearing. Tap lightly if necessary, to loosen. The shaft slides out of the small pinion gear and washer.

13.Carefully lift shaft and friction disc out of unit. As you remove the assembly, the washers between the bearing and sliding forks will be loose. Do not lose the washers.

 

 

 

 

 

6

 

11

5

1

2

3

4

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

6

9

8

7

 

 

 

 

1. Hex Shaft

 

7. Bearing Cap Screws

2. Friction Disc

 

8. Bearing Cap/Bushing

3. Hex Bolts & Nuts

 

9. Clutch Fork

4. Shift Carrier

 

10.Large Gear

5. Roll Pins

 

11.Pinion Gear

6. Washers

 

 

 

 

Figure 30

OS2002

 

Replace Friction Disc

1.Remove three hex bolts and nuts holding friction disc to shift carrier.

2.Remove the old friction disc. Put the new friction disc in place, flat side to the shift carrier.

3.Reinstall the three bolts and nuts into the new friction disc and hub. Torque to 5-6 lbf-ft (6.8 to 8.13 N•m).

Reinstall Friction Disc

1.Reinstall the shift carrier, the small pinion gear and washer onto the hex shaft. The washer goes between the bearing and the pinion gear.

2.Slide the shaft and attached parts into the frame, through the right side hole first, then the left. Pinion gear must mesh with the large gear.

3.Reinstall the flange bearing and washers into the shift forks. Be sure the washers are inside the forks.

4.Reinstall the bearing and outside bearing cap on the left side of the frame.

5.On the right side of the frame, place the washer on the end of the shaft.

6.Reinstall the bearing cap/bushing on the right side of frame.

7.Reinstall roll pins in shaft. Be sure pins are centered in shaft.

8.Connect the pivot pin to the speed selector arm with the hardware removed in step 6 of Remove Friction Disc on page 23.

9.Reinstall tires with lockpins.

10.Install bottom cover.

11.Set unit upright.

12.Connect spark plug wire to spark plug.

GB - 24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Sno-Thro Table of Contents IntroductionSafety Safety Decals and LocationsPersonal Safety Is Involved Become Alert Obey The Message Safety Rules Clogs or servicingPage Page Assembly Package ContentsAssembly Install Discharge Chute Crank Check Tire PressureCheck Auger Gearcase Oil Check Engine Crankcase OilControls and Features 932046, 047932045 Operation Primer BulbAttachment Clutch Right Hand Lever Speed Selector Engine Shut-Off Switch Snow Clean-Out Tool FigureChoke Control Knob 932046, 047 932045 Throttle 932046, 047Filling Fuel Tank PRE-START To Stop in AN EmergencyStarting and Shut OFF Snow Removal TravelingTransport Shut OffMaintenance Change Engine OIL Check Tire PressureCheck Auger Gearcase General LubricationService and Adjustments Scraper BladeRunners Shear BoltsSpeed Selector Adjustment Attachment Drive Belt ReplacementRemove Attachment Drive Belt Brake Adjustment below Replace Attachment Drive BeltTraction Drive Belt Replacement AdjustmentAttachment CLUTCH/BRAKE Attachment Clutch Lever In. 7 15,2 cm 17,8 cm Traction Drive Clutch Adjustment Friction Disc ReplacementRemove Friction Disc Reinstall Friction Disc Replace Friction DiscService Parts AccessoriesStorage Troubleshooting Selector Adjustment onSpecifications EngineAriens Limited Warranties Exceptions, Limitations, Exclusions

932045 - ST8524E, 932048 - ST5520, 932046 - ST724E, 932047 - ST5524E specifications

The Ariens brand has long been synonymous with quality and durability in outdoor power equipment, particularly in snow blowers. The models Ariens 932047 (ST5524E), 932046 (ST724E), 932048 (ST5520), and 932045 (ST8524E) each deliver exceptional performance designed to handle a variety of winter conditions.

The Ariens 932047 - ST5524E is particularly well-regarded for its efficient 24-inch clearing width, making it ideal for residential driveways and sidewalks. With a powerful 223cc engine, this model provides ample power to tackle heavy, wet snow. It features a 200-degree chute rotation, which allows for precise snow throwing, enabling users to direct snow exactly where it is needed. The easy-to-use controls make operation simple, even in the harshest weather.

Similarly, the 932046 - ST724E offers a wider clearing width of 24 inches as well, paired with a robust 254cc engine. This model excels in heavy snow conditions, thanks to its deep-set auger design that effortlessly breaks down tough snow layers. The adjustable skid shoes enhance stability and control, while the electric start feature provides convenient starting, even in the coldest temperatures.

The Ariens 932048 - ST5520 is a slightly more compact option, maintaining a 20-inch clearing width and featuring a reliable 223cc engine. This snow blower is perfect for those with tighter spaces to clear, like alleys or smaller driveways. Its lightweight construction makes it easy to maneuver, while still providing the power needed for effective snow removal. The intuitive controls and multiple speed settings provide flexibility for the user.

Lastly, the 932045 - ST8524E stands out with its impressive 28-inch clearing width, making quick work of large areas. The 306cc engine is among the most powerful in the lineup, allowing it to handle even the toughest snowfalls with ease. This model incorporates advanced features like an automatically adjustable auger and impeller, maximizing performance in various snow conditions.

All four models incorporate Ariens’ signature build quality, ensuring long-lasting performance and reliability. With features like reinforced steel construction, adjustable skid shoes, and user-friendly designs, these snow blowers are perfect for tackling winter’s toughest challenges.
Top Page Image Contents