Ariens 932048 - ST5520 manual Traction Drive Belt Replacement, Attachment CLUTCH/BRAKE, Adjustment

Page 21

 

 

 

 

TRACTION DRIVE BELT REPLACEMENT

 

 

932045

 

 

 

 

NOTE: Housing and frame must be tipped apart and

 

 

 

 

1

2

4

5

attachment drive belt removed from engine sheave in

 

 

 

 

order to change traction drive belt (Figures 21, 22, 23

 

 

 

 

and 24).

 

CAUTION: Always support Sno-Thro frame

 

and blower housing when loosening the cap

 

screws holding them together. Never loosen

9

cap screws while unit is in service position.

 

 

1. Remove attachment drive belt (See Remove

 

Attachment Drive Belt on page 19).

2. Pull idler away from traction drive belt and remove belt from idler, camshaft pulley and driven pulley (it may be necessary to turn camshaft pulley using recoil starter handle).

 

 

 

NOTE: To gain clearance, engage traction clutch and if

 

 

 

necessary pull back attachment idler arm.

8

7

3

3. Replace traction drive belt.

6

4. Replace attachment drive belt (See Replace

 

 

 

 

 

Attachment Drive Belt on page 20).

 

1. Attachment Drive Belt

ATTACHMENT CLUTCH/BRAKE

 

2. Engine Sheave

 

 

 

ADJUSTMENT

 

3. Traction Drive Belt

4. Camshaft Pulley

 

 

5. Traction Belt Idler

 

WARNING: IMPROPER ADJUSTMENT

6. Attachment Pulley

 

 

could result in unexpected movement of

7. Attachment Idler Nut

 

8. Attachment Belt Idler

 

auger and impeller causing death or serious

9. Belt Finger

 

injury. AUGER / IMPELLER MUST STOP

Figure 23

 

within 3 seconds when Attachment

OS7245

Clutch/Impeller Brake Lever is released.

 

1/16 to 1/8 in.

 

WARNING: Adjustment procedure requires

(1.6–3 mm)

 

 

the engine to be run with the belt cover off.

 

 

 

 

AVOID INJURY. Read and understand the

 

2

entire Safety section before proceeding.

 

1. Check attachment clutch lever measurement.

 

 

1

 

a. Start engine and run at full throttle.

 

 

b. Slowly squeeze the attachment clutch lever

 

 

until auger shaft begins to rotate.

2

 

c. Measure the distance from the end of the

 

clutch lever to the handlebar as shown in

 

 

 

1

Figure 25. The distance between the clutch

 

lever and the handlebar should be 6 in. - 7 in.

1/16 to 1/8 in.

 

(15,2 cm - 17,8 cm).

(1.6–3 mm)

 

d. Shut off engine.

1. Belt Finger

 

e. If clutch lever measurement is within

 

specified range, no adjustment is necessary.

2. Belt

 

 

If clutch lever measurement is outside the

 

 

Figure 24

OS7250

specified range, follow steps 2 - 7.

 

 

 

 

GB - 21

Image 21
Contents Sno-Thro Introduction Table of ContentsSafety Safety Decals and LocationsPersonal Safety Is Involved Become Alert Obey The Message Clogs or servicing Safety RulesPage Page Assembly Package ContentsAssembly Check Tire Pressure Install Discharge Chute CrankCheck Auger Gearcase Oil Check Engine Crankcase Oil932046, 047 Controls and Features932045 Operation Primer BulbAttachment Clutch Right Hand Lever Speed Selector Snow Clean-Out Tool Figure Engine Shut-Off SwitchChoke Control Knob 932046, 047 932045 Throttle 932046, 047Filling Fuel Tank PRE-START To Stop in AN EmergencyStarting and Shut OFF Traveling Snow RemovalTransport Shut OffMaintenance Check Tire Pressure Change Engine OILCheck Auger Gearcase General LubricationScraper Blade Service and AdjustmentsRunners Shear BoltsSpeed Selector Adjustment Attachment Drive Belt ReplacementRemove Attachment Drive Belt Replace Attachment Drive Belt Brake Adjustment belowTraction Drive Belt Replacement AdjustmentAttachment CLUTCH/BRAKE Attachment Clutch Lever In. 7 15,2 cm 17,8 cm Traction Drive Clutch Adjustment Friction Disc ReplacementRemove Friction Disc Replace Friction Disc Reinstall Friction DiscService Parts AccessoriesStorage Selector Adjustment on TroubleshootingEngine SpecificationsAriens Limited Warranties Exceptions, Limitations, Exclusions

932045 - ST8524E, 932048 - ST5520, 932046 - ST724E, 932047 - ST5524E specifications

The Ariens brand has long been synonymous with quality and durability in outdoor power equipment, particularly in snow blowers. The models Ariens 932047 (ST5524E), 932046 (ST724E), 932048 (ST5520), and 932045 (ST8524E) each deliver exceptional performance designed to handle a variety of winter conditions.

The Ariens 932047 - ST5524E is particularly well-regarded for its efficient 24-inch clearing width, making it ideal for residential driveways and sidewalks. With a powerful 223cc engine, this model provides ample power to tackle heavy, wet snow. It features a 200-degree chute rotation, which allows for precise snow throwing, enabling users to direct snow exactly where it is needed. The easy-to-use controls make operation simple, even in the harshest weather.

Similarly, the 932046 - ST724E offers a wider clearing width of 24 inches as well, paired with a robust 254cc engine. This model excels in heavy snow conditions, thanks to its deep-set auger design that effortlessly breaks down tough snow layers. The adjustable skid shoes enhance stability and control, while the electric start feature provides convenient starting, even in the coldest temperatures.

The Ariens 932048 - ST5520 is a slightly more compact option, maintaining a 20-inch clearing width and featuring a reliable 223cc engine. This snow blower is perfect for those with tighter spaces to clear, like alleys or smaller driveways. Its lightweight construction makes it easy to maneuver, while still providing the power needed for effective snow removal. The intuitive controls and multiple speed settings provide flexibility for the user.

Lastly, the 932045 - ST8524E stands out with its impressive 28-inch clearing width, making quick work of large areas. The 306cc engine is among the most powerful in the lineup, allowing it to handle even the toughest snowfalls with ease. This model incorporates advanced features like an automatically adjustable auger and impeller, maximizing performance in various snow conditions.

All four models incorporate Ariens’ signature build quality, ensuring long-lasting performance and reliability. With features like reinforced steel construction, adjustable skid shoes, and user-friendly designs, these snow blowers are perfect for tackling winter’s toughest challenges.