Ariens 932045 - ST8524E manual Snow Removal, Traveling, Transport, Shut Off, Tips for Operation

Page 15

4.Make sure that the traction clutch and attachment drive clutch levers are fully disengaged.

5.Push Primer Bulb 2 or 3 times for cold engine.

NOTE: When temperature is below -15° F (-26° C) additional priming may be needed.

6.Insert key into ignition switch on engine and push into "Run" position. DO NOT twist key after it is inserted.

7.If engine is cold, apply choke. A warm engine requires less choking than a cold engine. See Engine Manual for detailed instructions.

8.Set throttle to proper starting position (932046, 047).

9.Turn on engine shut-off switch ("ON").(932045)

10.Press starter button on engine until engine starts.

IMPORTANT: DO NOT operate starter more than 15 seconds per minute, as overheating and damage can occur. (If engine does not start, refer to TROUBLESHOOTING on page 26.)

11.Adjust choke as needed.

12.Disconnect power cord from outlet, then starter.

13.Set throttle to Part Throttle or Slow position for adaptation to outside temperature or travel. Set throttle to Fast position for normal operation.

(932046, 047)

Shut Off

1.Release Traction Drive Clutch Lever and allow unit to come to a complete stop.

2.Run Impeller a few minutes after use to prevent freeze-up of Impeller.

3.Release Attachment Clutch Lever and wait for all moving parts to come to a complete stop.

4.Move Throttle to the “Stop” position. (932046, 047, 048)

5.Turn off engine shut-off switch ("OFF"). (932045)

6.Remove key.

SNOW REMOVAL

IMPORTANT: Allow unit and engine to adjust to the outdoor temperature before clearing snow.

NOTE: Attachment clutch should be engaged before wheel drive clutch when throwing snow.

1.Select Speed Control position and direction.

2.Engage Attachment Clutch - Right Hand Lever.

3.Engage Traction Drive Clutch - Left Hand Lever.

IMPORTANT: DO NOT overload unit capacity by attempting to clear snow at too fast a rate. Use slow speed to clear deep or hard packed snow.

Tips for Operation

Snow is best removed as soon as possible after snow fall.

To clear an area, run unit in an overlapping series of paths. For large areas, start in the middle and throw snow to each side, so snow is not cleared more than once.

ALWAYS direct snow away from area to be cleared and with direction of the wind.

TRAVELING

To travel from one work area to another:

1.Set Throttle to Slow or Part-Throttle position.

2.Press down on handlebars enough to raise front of unit slightly off surface.

3.Engage wheel drive clutch without engaging attachment drive clutch.

TRANSPORT

ALWAYS shut off engine, remove key, and close fuel shut-off valve when transporting unit on a truck or trailer.

Use extra care when loading or unloading unit onto trailer or truck.

Secure unit chassis to transport vehicle. NEVER secure from rods or linkages that could be damaged.

DO NOT transport machine while engine is running.

GB - 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Sno-Thro Introduction Table of ContentsSafety Safety Decals and LocationsPersonal Safety Is Involved Become Alert Obey The Message Clogs or servicing Safety RulesPage Page Assembly Package ContentsAssembly Check Engine Crankcase Oil Install Discharge Chute CrankCheck Tire Pressure Check Auger Gearcase Oil932046, 047 Controls and Features932045 Operation Primer BulbAttachment Clutch Right Hand Lever Speed Selector Throttle 932046, 047 Engine Shut-Off SwitchSnow Clean-Out Tool Figure Choke Control Knob 932046, 047 932045Filling Fuel Tank PRE-START To Stop in AN EmergencyStarting and Shut OFF Shut Off Snow RemovalTraveling TransportMaintenance General Lubrication Change Engine OILCheck Tire Pressure Check Auger GearcaseShear Bolts Service and AdjustmentsScraper Blade RunnersSpeed Selector Adjustment Attachment Drive Belt ReplacementRemove Attachment Drive Belt Replace Attachment Drive Belt Brake Adjustment belowTraction Drive Belt Replacement AdjustmentAttachment CLUTCH/BRAKE Attachment Clutch Lever In. 7 15,2 cm 17,8 cm Traction Drive Clutch Adjustment Friction Disc ReplacementRemove Friction Disc Replace Friction Disc Reinstall Friction DiscService Parts AccessoriesStorage Selector Adjustment on TroubleshootingEngine SpecificationsAriens Limited Warranties Exceptions, Limitations, Exclusions

932045 - ST8524E, 932048 - ST5520, 932046 - ST724E, 932047 - ST5524E specifications

The Ariens brand has long been synonymous with quality and durability in outdoor power equipment, particularly in snow blowers. The models Ariens 932047 (ST5524E), 932046 (ST724E), 932048 (ST5520), and 932045 (ST8524E) each deliver exceptional performance designed to handle a variety of winter conditions.

The Ariens 932047 - ST5524E is particularly well-regarded for its efficient 24-inch clearing width, making it ideal for residential driveways and sidewalks. With a powerful 223cc engine, this model provides ample power to tackle heavy, wet snow. It features a 200-degree chute rotation, which allows for precise snow throwing, enabling users to direct snow exactly where it is needed. The easy-to-use controls make operation simple, even in the harshest weather.

Similarly, the 932046 - ST724E offers a wider clearing width of 24 inches as well, paired with a robust 254cc engine. This model excels in heavy snow conditions, thanks to its deep-set auger design that effortlessly breaks down tough snow layers. The adjustable skid shoes enhance stability and control, while the electric start feature provides convenient starting, even in the coldest temperatures.

The Ariens 932048 - ST5520 is a slightly more compact option, maintaining a 20-inch clearing width and featuring a reliable 223cc engine. This snow blower is perfect for those with tighter spaces to clear, like alleys or smaller driveways. Its lightweight construction makes it easy to maneuver, while still providing the power needed for effective snow removal. The intuitive controls and multiple speed settings provide flexibility for the user.

Lastly, the 932045 - ST8524E stands out with its impressive 28-inch clearing width, making quick work of large areas. The 306cc engine is among the most powerful in the lineup, allowing it to handle even the toughest snowfalls with ease. This model incorporates advanced features like an automatically adjustable auger and impeller, maximizing performance in various snow conditions.

All four models incorporate Ariens’ signature build quality, ensuring long-lasting performance and reliability. With features like reinforced steel construction, adjustable skid shoes, and user-friendly designs, these snow blowers are perfect for tackling winter’s toughest challenges.
Top Page Image Contents