Intel S5000XAL manual 1.5 PE4, PE5 Two x4 PCI Express* Bus Segments, PCI Riser Slots

Page 34

Intel® Server Board S5000PAL / S5000XAL TPS

Functional Architecture

3.2.1.5PE4, PE5: Two x4 PCI Express* Bus Segments

Two x4 PCI Express* bus segments are directed through the MCH. These PCI Express segments, PE4 and PE5, support one x8 or two x4 PCI Express segments to the low profile riser slot (J5B1).

3.2.1.6PE6, PE7: Two x4 PCI Express* Bus Segments

Two x4 PCI Express* bus segments are directed through the MCH. These PCI Express segments, PE6 and PE7, support one x8 or two x4 PCI Express segments to the full height riser slot (J4F1).

3.2.1.7PCI Riser Slots

The server board has two riser slots capable of supporting riser cards for both 1U and 2U system configurations. Because of board placement resulting in different pin orientations, and expanded technology support associated with the full-height riser, the riser slots are not the same and require different riser cards.

The low profile riser slot (J5B1) utilizes a 98-pin connector. It is capable of supporting one x8 (1U) or two x4 (2U) low profile PCI Express* add-in cards. The x8 PCI Express* bus can support bus speeds of up to 20 Gb/S. The following table provides the supported bus throughput for the given riser card used and the number of add-in cards installed.

 

Low Profile Riser

1 add-in card populated

1U

– 1 add-in card slot

x8 or x4

2U

– 2 add-in card slots

x4

2add-in cards populated

NA x4

Note: There are no population rules for installing a single low profile add-in card in the 2U LP riser card; a single add in card can be installed in either PCI Express* slot. While each slot can accommodate a x8 card, each slot will only support x4 bus speeds.

The full height riser slot (J4F1) implements Intel® Adaptive Slot Technology. This 280-pin connector is capable of supporting riser cards that meet either the PCI-X* or PCI Express* technology specifications. The following tables show the maximum bus speed supported with different add-in card populations for each supported riser card.

Full Height PCI-X*

1 add-in card populated

2 add-in cards populated

3 add-in cards populated

(Passive) Riser

 

 

 

 

 

 

 

1U – 1 add-in card slot

Up to 133MHz

NA

NA

2U – 3 add-in card slots

Up to 100MHz in top PCI

Up to 100MHz using top

66MHz

 

slot

and middle slots

 

Note: For the 2U PCI-X* (passive) riser card, add-in cards should be installed starting with the top slot first, followed by the middle, and then the bottom. Any add-in card populated in the bottom PCI slot will cause the bus to operate at 66MHz.

Full Height PCI-X*

1 add-in card populated

2 add-in cards populated

3 add-in cards populated

(Active) Riser

 

 

 

 

 

 

 

2U – 3 add-in card slots

Up to 133MHz

Up to 133MHz

Up to 133MHz

Note: Each PCI slot on the 2U PCI-X* (active) riser card operates on an independent PCI bus. Therefore, using an add-in card that operates below 133MHz will not affect the bus speed of the other PCI slots.

Revision 1.4

35

 

Intel order number: D31979-007

Image 34
Contents Revision Intel order number D31979-007Intel Server Board S5000PAL / S5000XAL TPSRevision History IiiDate Revision Modifications Number Disclaimers Disclaimers Intel Server Board S5000PAL / S5000XAL TPSTable of Contents Light Guided Diagnostics Jumper Block SettingsPower and Environmental Specifications 108 101105 111List of Figures Intel Server Board S5000PAL / S5000XAL TPS Viii Revision Intel order number D31979-007List of Tables Intel Server Board S5000PAL / S5000XAL TPS List of TablesList of Tables Intel Server Board S5000PAL / S5000XAL TPS Page Introduction Intel Server Board S5000PAL / S5000XAL TPS Chapter OutlineServer Board Use Disclaimer 12Revision Intel order number D31979-007Feature Description Intel Server Board S5000PAL / S5000XAL Feature SetIntel Server Board S5000PAL / S5000XAL TPS Product Overview Product Overview Intel Server Board S5000PAL / S5000XAL TPS Server Board Layout14Revision Intel order number D31979-007 Connector and Component Locations Sata Light Guided Diagnostic LED Locations LDMExternal I/O Connector Locations Server Board Mechanical Drawings 40.39 PCI BKT Drop Down TP02294 10.16 16.51 113.13 199.21 285.75 182.83 274.32 298.51 Functional Architecture System Bus Interface Intel 5000P and 5000X Memory Controller Hubs MCHProcessor Support Processor Support Matrix Processor Population RulesCommon Enabling Kit CEK Design Support 26Revision Intel order number D31979-007Memory Sub-system CEK Processor MountingMemory Rasum Featuresi Supported MemoryDimm Population Rules and Supported Dimm Configurations Minimum Non-Mirrored Mode ConfigurationBranch Channel B Channel a Non-mirrored mode memory upgrades Recommended Four Dimm ConfigurationSingle Branch Mode Sparing Dimm Configuration 32Revision Intel order number D31979-007ESB-2 IO Controller Snoop Filter 5000X MCH onlyPXA 64-bit, 133MHz PCI-X* Bus Segment PCI Sub-system1.1 PCI32 32-bit, 33-MHz PCI Bus Segment 1.3 PE1 One x4 PCI Express* Bus Segment1.6 PE6, PE7 Two x4 PCI Express* Bus Segments 1.5 PE4, PE5 Two x4 PCI Express* Bus SegmentsPCI Riser Slots Intel Embedded Server RAID Technology II Support Serial ATA Support36Revision Intel order number D31979-007 USB 2.0 Support Video SupportParallel ATA Pata Support Intel Embedded Server RAID Technology Option ROMDual Video Video ModesVideo Memory Interface Video ModesMAC Address Definition Network Interface Controller NICIntel I/O Acceleration Technology NIC2 Status LEDSerial Ports Pin Signal Name Serial Port a Header Pin-outSuper I/O Serial a Header Pin-outFloppy Disk Controller Pins What happens at system reset…RJ45 Signal Abbreviation Keyboard and Mouse SupportSystem Health Support Wake-up Control42Revision Intel order number D31979-007 Platform Management Board Connector Matrix Board Connector Information44Revision Intel order number D31979-007 Power Connector Pin-out J3K4 Power ConnectorsPower Connector Pin-out J3K3 Power Supply Signal Connector Pin-out J1K1Pin Signal Name Intel Remote Management Module RMM ConnectorIntel RMM Connector Pin-out J1C5 System Management HeadersIntel RMM NIC Connector Pin Intel RMM NIC Module Connector Pin-out J1B23 LCP/AUX Ipmb Header Riser Card SlotsIpmb Header Pin-Side B PCI Spec Signal Pin-Side a PCI Spec Signal Pin Side B PCI Spec SignalPin Side a PCI Spec Signal Full-height Riser Slot Pin-out J4F150Revision Intel order number D31979-007 Pin-Side B PCI Spec Signal Pin-Side a 52Revision Intel order number D31979-007 PAR64Front Panel SSI Standard 24-pin Connector Pin-out J3H2 SSI Control Panel ConnectorBridge Board Connector Pin Bridgeboard Connector Pin-out J4G154Revision Intel order number D31979-007 NIC Connectors I/O Connector Pin-out DefinitionVGA Connector VGA Connector Pin-out J6A1Pin IDE Connector Pin-out J3G1 IDE ConnectorIntel I/O Expansion Module Connector 56Revision Intel order number D31979-007Sata Connectors Sata Connector Pin-out J1H1, J1G2, J1G1, J1F2, J1E3Serial Port Connectors Keyboard and Mouse ConnectorExternal USB Connector Pin-out J5A1, J6A2 USB 2.0 ConnectorsInternal USB Connector Pin-out J1J1 Fan Headers SSI Fan Connector Pin-out J9K1,J5K1,J3K1,J3K2,J7A2,J7A1Pin Signal Name Type Description 60Revision Intel order number D31979-007Recovery Jumpers J1D1, J1D2, J1D3 Recovery Jumper BlocksJumper Name Pins What happens at system reset… BMC Force Update Procedure Cmos Clear and Password Reset Usage Procedure62Revision Intel order number D31979-007 Bios Select Jumper Bios Select Jumper J3H1External RJ45 Serial Port Jumper Block Light Guided Diagnostics 5-Volt Standby LEDSystem ID LED and System Status LED 66Revision Intel order number D31979-007System Status LED BMC Initialization Color State Criticality DescriptionDimm Fault LEDs Processor Fault LEDPost Code Diagnostic LEDs Server Board Design Specifications 70Revision Intel order number D31979-007Processor Power Support Server Board Power RequirementsTDP Power Max Tcase Icc MAX 130 W 70º C 150 a No load operating range Turn On No Load OperationLoad Ratings 72Revision Intel order number D31979-007Remote Sense GroundingStandby Outputs Voltage RegulationCapacitive Loading Common Mode NoiseDynamic Loading Closed-Loop StabilityTiming Requirements Ripple / NoiseSoft Starting Ripple and NoiseOut 10% V out MIN MAX Units Residual Voltage Immunity in Standby Mode 78Revision Intel order number D31979-007Australia / New Zealand AS/NZS 3548 Emissions Product Safety & Electromagnetic EMC ComplianceReference Example ICES-003 Canada Electromagnetic Compatibility NoticesFCC Verification Statement USA Europe CE Declaration of ConformityRRL Korea Bsmi TaiwanEnglish translation of the notice above Product Ecology Compliance Japan Recycling Other MarkingsCompliance Compliance Reference Description Marking Example Appendix a Integration and Usage Tips 84Revision Intel order number D31979-007ƒ Event / Reading Type ƒ Assertion / De-assertion Enablesƒ Sensor Type ƒ Event Offset/Triggersƒ Standby ƒ Default Hysteresisƒ Criticality 86Revision Intel order number D31979-007Value Bility Type NMI STB Revision Revision Intel order number D31979-007 Revision Acpi Bios EPS PCIe Link1 Revision Dimm A2 Dimm D2 ECC 100 Revision Intel order number D31979-007 B01 DimmPost Progress Code LED Example LEDs Red Green102Revision Intel order number D31979-007 Revision 103 Intel order number D31979-007 Pre-EFI Initialization Module Peim / Recovery Runtime Phase / EFI Operating System Boot104Revision Intel order number D31979-007 Error Code Error Message Response Post Error Messages and HandlingRevision Intel order number D31979-007 105 106Revision Intel order number D31979-007 ROMBMC Beep Codes Post Error Beep CodesPost Error Beep Codes Revision 107 Intel order number D31979-007Appendix E Supported Intel Server Chassis Page Slim-Line Optical Drive Bay Revision 111 Intel order number D31979-007 Intel Server Board S5000PAL / S5000XAL TPS GlossaryTerm Definition Glossary Intel Server Board S5000PAL / S5000XAL TPS 112Revision Intel order number D31979-007Revision 113 Intel order number D31979-007 Reference Documents 114Revision Intel order number D31979-007