Eiki LC-SD10 owner manual Preparation, Connecting the AC Power Cord, Projector side AC Outlet side

Page 12

Preparation

Connecting the AC Power Cord

This projector uses nominal input voltages of 100-120 V or 200-240 V AC. This projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system.

Consult your authorized dealer or service station if you are not sure of the type of power supply being in use.

Connect a projector with a peripheral equipment before turning a projector on. (Refer to page 15 –16 for connection.)

CAUTION

For safety, unplug the AC Power Cord when an appliance is not used. When this projector is connected to the outlet with the AC Power Cord,

an appliance is in Stand-by Mode and consumes a little electric power.Connect AC Power Cord (supplied) to the projector. The AC outlet must be near this equipment and must be easily accessible.

Note:

AC Power Cord must meet requirement of the country where you use the projector.

Confirm an AC plug type with the chart below and proper AC Power Cord must be used.

If supplied AC Power Cord does not match your AC outlet, contact your sales dealer.

Projector side

AC Outlet side

 

For the U.S.A. and Canada

For Continental Europe

 

Ground

 

To POWER CORD

To the AC Outlet.

To the AC Outlet.

CONNECTOR on your

projector.

(120 V AC)

(200 - 240 V AC)

12

Image 12
Contents Model LC-SD10 To the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandInstalling the Projector in Proper Position Air CirculationMoving the Projector Compliance Federal Communication Commission NoticeTable of Contents Features and Design Overview FrontBack BottomTop panel Terminals Remote Control Operating RangeConnecting the AC Power Cord PreparationProjector side AC Outlet side For the U.S.A. and Canada For Continental EuropeAdjustable Feet Positioning the ProjectorRemote Control Battery Installation Remove the batteryAttaching the Lens Cover Compartment lidInstallation Connecting to a ComputerTerminals of the Projector Cables used for connectionConnecting to Video Equipment Terminals of the Projector Cables used for connectionVideo Source example Component video output Video Cassette Recorder Video Disc PlayerHow to Operate the On-Screen Menu Respective adjustmentRemote Control Before OperationSetting Menu Input Menu PC Adjust Menu Image Adjust MenuAV System Menu Image Adjust Menu Menu BarBasic Operation Turning On the ProjectorTurning Off the Projector Adjusting the Screen Zoom AdjustmentFocus Adjustment Keystone AdjustmentSound Adjustment Timer FunctionNo Show Function Direct OperationComputer Input Input Source SelectionRGB Auto Mode Computer System SelectionSelecting Computer System Manually SvgaPC Adjustment Auto PC AdjustmentPC Adjust Menu Auto PC AdjManual PC Adjustment Reset Mode freeDisplay area Display area HImage Level Selection Direct OperationMenu Operation Image Level Adjustment Screen Size Adjustment Video Input Input Source Selection Video, S-VideoInput Menu VideoWhen the input source is coming from video Input Source Selection Component, RGB Scart 21-pinComponent Equipment connected to the ComputerVideo System Selection Video Jack or S-Video JackComputer in / Component in Jack Y, Pb/Cb, Pr/Cr AutoPicture level adjusted for the picture with fine tone User preset picture adjustment in Image Adjust Menu P34-35Cinema Image button Standard CinemaColor TintSharpness Progressive Closes the Image MenuProvides image at a normal video aspect ratio of 4 Provides image at a wide screen ratio of 16Setting Setting MenuCeiling function Rear function Power management Lamp modeCeiling RearTo change the code of the remote control Remote ControlFactory default To change the code of the projectorUsing the Presentation Remote Control Presentation Remote ControlInstallation Compatible computersMaintenance Lamp ReplacementReplacement Lamp Type No Lamp ReplaceReset the lamp replace counter Lamp Replace CounterProjector is shut down and the Warning indicator lights red Top ControlThen check the items below Cleaning the Projection Lens Follow these steps to clean the projection lensCloth. Avoid using an excessive amount of cleaner. Abrasive Air FilterTroubleshooting Problem No power Image is out of focusSome displays are not seen during the Operation Problem Check the mouse setting on your computerNot work Indicators and Projector Condition Menu Tree Computer InputVideo Input Settings Main menuSound System Image SelectCompatible Computer Specifications FreqKHz 43.269Technical Specifications Configuration of Terminals Optional PartsCOMPONENT-VGA Cable Type No SCART-VGA Cable Type NoKey to better communications Canada