Eiki LC-SD10 owner manual Compliance, Federal Communication Commission Notice

Page 5

Compliance

Federal Communication Commission Notice

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Number

: LC-SD10

Model Number

: TGX0043-011010 (1AV4U20B69000)

Trade Name

: EIKI

 

IR Presentation Remote Receiver for Projector

Responsible party

: EIKI International Inc.

Trade Name

: HOSIDEN

Address

: 30251 Esperanza, Rancho Santa Margarita,

Responsible Party

: Hosiden America Corp.

 

CA 92688-2132

Address

: 120 East State Parkway, Schaumburg, IL, 60173

Telephone No.

: (800)242-3454 (949-457-0200)

Telephone No.

: (847)885-8870

AC Power Cord Requirement

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the

plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be

GROUND

 

unable to insert the plug into the outlet, contact your electrician.

 

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

5

Image 5
Contents Model LC-SD10 Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsMoving the Projector Installing the Projector in Proper PositionAir Circulation Federal Communication Commission Notice ComplianceTable of Contents Features and Design Front OverviewBack BottomTop panel Terminals Operating Range Remote ControlPreparation Connecting the AC Power CordProjector side AC Outlet side For the U.S.A. and Canada For Continental EuropePositioning the Projector Adjustable FeetRemove the battery Remote Control Battery InstallationAttaching the Lens Cover Compartment lidConnecting to a Computer InstallationTerminals of the Projector Cables used for connectionTerminals of the Projector Cables used for connection Connecting to Video EquipmentVideo Source example Component video output Video Cassette Recorder Video Disc PlayerRespective adjustment How to Operate the On-Screen MenuRemote Control Before OperationInput Menu PC Adjust Menu Image Adjust Menu Setting MenuAV System Menu Image Adjust Menu Menu BarTurning Off the Projector Basic OperationTurning On the Projector Zoom Adjustment Adjusting the ScreenFocus Adjustment Keystone AdjustmentTimer Function Sound AdjustmentNo Show Function Direct OperationRGB Computer InputInput Source Selection Computer System Selection Auto ModeSelecting Computer System Manually SvgaAuto PC Adjustment PC AdjustmentPC Adjust Menu Auto PC AdjManual PC Adjustment Mode free ResetDisplay area Display area HMenu Operation Image Level SelectionDirect Operation Image Level Adjustment Screen Size Adjustment Input Source Selection Video, S-Video Video InputInput Menu VideoInput Source Selection Component, RGB Scart 21-pin When the input source is coming from videoComponent Equipment connected to the ComputerVideo Jack or S-Video Jack Video System SelectionComputer in / Component in Jack Y, Pb/Cb, Pr/Cr AutoUser preset picture adjustment in Image Adjust Menu P34-35 Picture level adjusted for the picture with fine toneCinema Image button Standard CinemaSharpness ColorTint Closes the Image Menu ProgressiveProvides image at a normal video aspect ratio of 4 Provides image at a wide screen ratio of 16Setting Menu SettingLamp mode Ceiling function Rear function Power managementCeiling RearRemote Control To change the code of the remote controlFactory default To change the code of the projectorPresentation Remote Control Using the Presentation Remote ControlInstallation Compatible computersLamp Replacement MaintenanceReplacement Lamp Type No Lamp ReplaceLamp Replace Counter Reset the lamp replace counterThen check the items below Projector is shut down and the Warning indicator lights redTop Control Follow these steps to clean the projection lens Cleaning the Projection LensCloth. Avoid using an excessive amount of cleaner. Abrasive Air FilterSome displays are not seen during the Operation TroubleshootingProblem No power Image is out of focus Not work ProblemCheck the mouse setting on your computer Indicators and Projector Condition Computer Input Menu TreeMain menu Video Input SettingsSound System Image SelectFreq Compatible Computer SpecificationsKHz 43.269Technical Specifications Optional Parts Configuration of TerminalsCOMPONENT-VGA Cable Type No SCART-VGA Cable Type NoKey to better communications Canada