Intel user manual MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000

Page 50

MicroJack User’s Manual

EYES Pro/MP2016/MP3000/MP5000

Event Search

Searches the recorded files by the alarm condition and action within a specified period of time.

To make the function workable, complete the following steps:

A.Click Event Search and the playback control panel will turn into the condition search panel as follows:

B.Choose the camera display mode … (1, 4, 9, 16 ch) from playback display mode.

C.Set up the initial and end time for searching in the time fields on the left bottom of the window.

D.Choose the search condition as the specified condition to search the file from the condition search panel; Motion detections, video loss, sensor inputs, relay outputs, audio, system call out, alarm recording.

E.Click Search Result to start searching and the coincident recorded files will be shown on the pop-up Event Table searching list.

F.Click Stop Search to stop searching if necessary.

MicroJack User’s Manual

EYES Pro/MP2016/MP3000/MP5000

G.Select the desired recorded files and click OK to hide Event Table. Meanwhile, the status of the files will be seen on event indicator and the playback control panel pops up to replace the condition search panel.

H.Click Playback button on the playback control panel, or, otherwise move the indicator on event indicator directly to display the files. During playing, the indicator will move with the display going and show the displaying time of the file in the field of the start time of the file.

I.Click Search Result to pop up the previous Event Table searching list and take the steps above to review the recorded file.

Note that the searched purplish red peaks in Event indicator field denote the recorded files that can be displayed on clicking them. However, the other searched peaks with other colors indicate the generations by the selected events that can’t be displayed on clicking them.

91

92

Image 50
Contents MicroJack Eyes Pro Digital Video Surveillance SystemMicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 ENGTable of Contents Appendix a Remote Login with AN MODEM-TO-MODEM Introduction Video Card Specification 4 portsPackage Contents Manual ConventionsHardware Recommendations Installing the Video Cards Eyes Pro Connecting the MicroJack Video CardsAttaching Cameras Connecting External Sensor/Relay Coil Ratings at 20 oCExternal I/O Box Pin Signals Pin # Definition Relay OutputsCheck Your Windows Version Driver InstallationInstalling the Driver in Windows 98SE/Me Select Specify a location and click the Next button Installing the Driver in Windows Click the Yes button to proceed with the installation MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Installing the Driver in Windows XP After the installation finished, click the Finish buttonRemove Your Video Card Driver MicroJack Eyes Pro/MP2016/MP3000/MP5000 surveillance system Software InstallationInstalling MicroJack Eyes Pro/MP2016/MP3000/MP5000 Software MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Product Update Product Present H/WSpecial Consideration System Configuration and OperationSystem Configuration Defrag Your Hard DiskBefore you start using it Ask for password when login Miscellaneous Beep if no signalAuto Reboot Assign Recording DisksDisplay & Recording Rate UPS Uninterruptible Power SupplyVideo Product Camera SetsDefault UpdateRestore Camera IDPreset Position Setup PTZ Camera SetupSelect a Com Port where PTZ camera connector connected PTZ CameraMicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Audio PropertiesMotion Detection Sensitivity Record when start monitoringRecord when motion detected Record with Time StampEdit ContentShield Start/ Stop MonitoringMicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Test RelaysSound Alarm You may right-click the mouse on Alarm to add a new alarmAlarm ID ConditionsMicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 General Server IP Event LogEnable Remote View server Multicast server via TCP/IP Enable WebCam ServerAsk for password when remote clients login Domain Name & PasswordBy Date By WeekdayMicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Task Enable Network ServerAlarm MonitorMicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Delete all. Don’t make copies MoveCopy DeviceFiles between the time Start & End LocationStart Time Days before scheduled datesMicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Map Configure e-map ImportCamera Information MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 EditArrange Cameras, Sensors, and Relays Add New UsersAuthorization Level MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 DeleteSystem Operation Product Models Eyes Pro/MP3004/MP5004Eyes Pro/MP2016/MP3016/MP5016 Display ModesStart / Stop AutoScan 10/13-Camera DisplayFull Screen Display Camera Display Check out Cameras, Sensors, Relays on the map Start / Stop MonitoringStart / Stop Audio Recording Monitoring Cameras, Sensors, and RelaysRed System ConfigurationCamera Blue Camera GreenSelect Time Audio PlaybackSelect Files to Play MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 PlayVideo Search MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 ZoomPrint & Save MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Exit MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Focus Preset Position NoPTZ Control Direction & Speed AutoPan Path GroupExit PTZ Controller Hard Disk Status Date / TimeUsing the WebCam Enable WebCamUse the WebCam Enable Web Cam see NetworkingCheck Enable WebCam server Accessing RemoteManager RemoteManagerMicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Login Alarm ReportSetup Display ModeMinimum Space & Safety Quota Camera Setup Relay Status Network SetupSensor Status Back to Main Menu Click Alarm Control to see the window for alarm statusOperating the RemoteManager Center ManagementConneting quality Camera Setup, please refer to 6.2.3 Camera Setup sectionUser Print Local PlaybackZoom In/Out SaveRemote Playback ChannelFocus out Direction ControlDirection Speed Zoom outRotation Speed deg/s Start RecordingExit RemoteManager ClearServer Appendix a Remote Login with an Modem-to-Modem ConnectionWindows 98SE / Windows Me 130 Windows 134 136 138 Button Windows XPSelect Accept incoming connections and click the Next 142 Button Enter the name of this connection and click the Next button Appendix B Registering Domain Name on Ddns Server User LoginPassword