Intel MP2016 User, Conneting quality, Camera Setup, please refer to 6.2.3 Camera Setup section

Page 63

MicroJack User’s Manual

EYES Pro/MP2016/MP3000/MP5000

Before arranging center manager section, please make sure RemoteView server enabled in networking section of System Configuration.

To offer the complete information, finish the steps below:

1.Click Center Manager button and the following window appears:

2.Click Add to include an available server to server list. The Add Server window will show as follows or click Delete or Update to modify the setting.

3.The multicast servers in LAN will be listed automatically on the left side of the dialog. You can highlight the server which you want to add and click OK or directly double click the server to add a new multicast server.

4.In order to add a new server in WAN, enter the IP Address or domain name of the desired server and the same port number as the setting in Networking section of the server (default 9090). Check Use Dial-Up Networking to configure the further setting of network if the network connection is via modem to modem. Click OK to start connecting or Cancel to quit the dialog.

MicroJack User’s Manual

EYES Pro/MP2016/MP3000/MP5000

5.The following pop-up window of Add Server will show the Server Name automatically if the IP Address is correct and has been connected. In that case the server name doesn’t show up, please check the connection between server and remote client.

If the port number has been changed in server end, please delete the server and set a new one.

User

Finish the user’s information given by the specified server.

Conneting quality

Here allows user to pick a proper conneting speed for each server to adjust the network quaility. Drag the slide bar to select one connecting speed out of 11 levels. Namely, if the update of the image is almost failed, you sould to increase the connectining speed. Note that the higher quality needs the higher baud rate. Click OK to save to add the new server in center management or Cancel to quit the setting.

Note that the connecting speed in remote client had better meet with that in server.

6.You will be prompted to click OK in the following window to into the Camera Setup window once one of the users of server has been deleted. About the instruction

of the Camera Setup, please refer to 6.2.3 Camera Setup section.

7.Repeat the steps above to add a new server. The maximum numbers of server are limited in 16 for the 16 channels.

117

118

Image 63
Contents Digital Video Surveillance System MicroJack Eyes ProENG MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000Table of Contents Appendix a Remote Login with AN MODEM-TO-MODEM Manual Conventions Video Card Specification 4 portsPackage Contents IntroductionHardware Recommendations Installing the Video Cards Connecting the MicroJack Video Cards Attaching CamerasEyes Pro Coil Ratings at 20 oC Connecting External Sensor/RelayRelay Outputs External I/O Box Pin Signals Pin # DefinitionDriver Installation Installing the Driver in Windows 98SE/MeCheck Your Windows Version Select Specify a location and click the Next button Installing the Driver in Windows Click the Yes button to proceed with the installation MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 After the installation finished, click the Finish button Installing the Driver in Windows XPRemove Your Video Card Driver Software Installation Installing MicroJack Eyes Pro/MP2016/MP3000/MP5000 SoftwareMicroJack Eyes Pro/MP2016/MP3000/MP5000 surveillance system MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Product Present H/W Product UpdateDefrag Your Hard Disk System Configuration and OperationSystem Configuration Special ConsiderationBefore you start using it Assign Recording Disks Miscellaneous Beep if no signalAuto Reboot Ask for password when loginProduct Camera Sets UPS Uninterruptible Power SupplyVideo Display & Recording RateCamera ID UpdateRestore DefaultPTZ Camera PTZ Camera SetupSelect a Com Port where PTZ camera connector connected Preset Position SetupProperties MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 AudioRecord with Time Stamp Record when start monitoringRecord when motion detected Motion Detection SensitivityStart/ Stop Monitoring ContentShield EditRelays MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 TestConditions You may right-click the mouse on Alarm to add a new alarmAlarm ID Sound AlarmMicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Event Log General Server IPDomain Name & Password Enable WebCam ServerAsk for password when remote clients login Enable Remote View server Multicast server via TCP/IPBy Weekday By DateMonitor Enable Network ServerAlarm MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 TaskMicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Device MoveCopy Delete all. Don’t make copiesDays before scheduled dates LocationStart Time Files between the time Start & EndConfigure e-map Import CameraMicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Map Add New Users MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 EditArrange Cameras, Sensors, and Relays InformationMicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Delete Authorization LevelProduct Models Eyes Pro/MP3004/MP5004 System OperationDisplay Modes Eyes Pro/MP2016/MP3016/MP501610/13-Camera Display Full Screen Display Camera DisplayStart / Stop AutoScan Monitoring Cameras, Sensors, and Relays Start / Stop MonitoringStart / Stop Audio Recording Check out Cameras, Sensors, Relays on the mapCamera Green System ConfigurationCamera Blue RedMicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Play Audio PlaybackSelect Files to Play Select TimeMicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Zoom Print & SaveVideo Search MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 Exit AutoPan Path Group Preset Position NoPTZ Control Direction & Speed MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 FocusExit PTZ Controller Date / Time Hard Disk StatusEnable WebCam Using the WebCamEnable Web Cam see Networking Check Enable WebCam serverUse the WebCam RemoteManager Accessing RemoteManagerDisplay Mode Alarm ReportSetup MicroJack User’s Manual Eyes Pro/MP2016/MP3000/MP5000 LoginMinimum Space & Safety Quota Camera Setup Network Setup Sensor StatusRelay Status Center Management Click Alarm Control to see the window for alarm statusOperating the RemoteManager Back to Main MenuCamera Setup, please refer to 6.2.3 Camera Setup section UserConneting quality Save Local PlaybackZoom In/Out PrintChannel Remote PlaybackZoom out Direction ControlDirection Speed Focus outClear Start RecordingExit RemoteManager Rotation Speed deg/sAppendix a Remote Login with an Modem-to-Modem Connection Windows 98SE / Windows MeServer 130 Windows 134 136 138 Windows XP Select Accept incoming connections and click the NextButton 142 Button Enter the name of this connection and click the Next button User Login PasswordAppendix B Registering Domain Name on Ddns Server