Intel CB60-BX, CB60-ZX manual Jumper Settings for Wake-On-Keyboard/ Wake-On-Mouse

Page 16

2

Hardware Installation

2.6Jumper Settings for Wake-On-Keyboard/ Wake-On-Mouse

Jumper JP1

Wake-On-Keyboard/Wake-On-Mouse

The system board supports the Wake- On-Keyboard/Wake-On-Mouse function. This function allows you to use the keyboard or mouse to power-on the system. By default, JP1 is disabled. To use this function, set JP1 to 2-3 On. “Keyboard/Mouse Power On” in the Integrated Peripherals setup of the Award BIOS must be set accordingly. Refer to chapter 3 for details.

Warning: 1. If JP1 was previously enabled

with a password set in the

“KB Power On Password” field, and now you wish to disable the Wake-On-Keyboard (password) function, make sure to set the “Keyboard/Mouse Power On” field to Disabled prior to setting JP1 to disabled. You will not be able to boot up the system if you fail to do so.

2.The power button will not function once a keyboard password has been set in the “KB Power On Password” field of the Integrated Peripherals setup. You must type the correct password to power-on the system.

3.The 5VSB power source of your power supply must support 720mA (minimum).

1 2 31 2 3

 

 

 

 

 

 

 

 

 

1-2 On: Disable

2-3 On: Enable

 

(default)

 

 

 

 

 

16

Image 16
Contents CB60-BX/ZX 37400849Copyright TrademarksFCC and DOC Statement on Class B Table of Contents Appendix a System Error Messages Appendix B TroubleshootingFeatures Features and SpecificationsIntroduction Connectors IntroductionExpansion Slots Desktop Management Interface DMISystem Health Monitor Functions PCI Bus Master IDE ControllerIrDA Interface USB PortsIntroduction Intelligence Package Checklist Virus ProtectionHardware Installation System Board LayoutHardware Installation DIP Switch Settings for Processors For Factory Use Only System MemoryJumper Settings for the CPU’s Front Side Bus Jumper JP2 CPU’s Front Side Bus SelectJumper Settings for Clearing Cmos Data Jumper JP3 Clear Cmos DataJumper Settings for Wake-On-Keyboard/ Wake-On-Mouse Jumper JP1 Wake-On-Keyboard/Wake-On-MouseSerial Ports 2 PS/2 Mouse and Keyboard PortsHardware Installation Parallel Ports Floppy Disk ControllerHardware Installation IDE Hard Disk Interface Adding a Second IDE Hard DriveHardware Installation USB Ports IrDA ConnectorHardware Installation CPU Fan Connector Chassis Fan ConnectorHardware Installation AGP Fan Connector SB-LINK ConnectorHardware Installation Wake-On-LAN Connector Hardware Installation Power Connector COM PW-OK 5VSBHardware Installation 14 J14 LEDs and Switches Keylock Power/Standby LED and Keylock Connector KeylockStandard Cmos Setup Award Bios Setup UtilityBasic Input/Output System Date Award Bios Setup UtilityTime Video Drive a and Drive BHalt On Award Bios Setup Utility Bios Features Setup Virus WarningQuick Power On Self Test Boot SequenceBoot Up Floppy Seek CPU L1 Cache and CPU L2 CacheBoot Up NumLock Status Typematic Rate SettingTypematic Delay Msec Typematic Rate Chars/SecOS Select for Dram 64MB Chipset Features SetupHDD S.M.A.R.T. Capability Sdram RAS-to-CAS Delay Dram Data Integrity Mode CB60-BX onlySystem Bios Cacheable Video Bios CacheableBit I/O Recovery Time and 16 Bit I/O Recovery Time Video RAM CacheableMemory Hole At 15M-16M PCI 2.1 ComplianceSpread Spectrum System Health MonitorCpuv Power Management Setup+1.5V, +3.3V, +5V, +12V, -12V Power Management Acpi FunctionPM Control by APM Video Off MethodStandby Mode Suspend ModeHDD Power Down Video Off AfterPWR Lost Resume State Soft-Off by PWR-BTTNResume On Ring Resume On Alarm Timer hhmmssResume On LAN Date of MonthReset Configuration Data Award Bios Setup Utility 5 PNP/PCI ConfigurationResources Controlled By Load Fail-Safe Settings Assign IRQ for VGAAssign IRQ for USB PCI Slot 1 Use IRQ to PCI Slot 4 Use IRQIDE HDD Block Mode Award Bios Setup Utility Load Optimal SettingsIntegrated Peripherals On-Chip Primary PCI IDE and On-Chip Secondary PCI IDE USB Keyboard SupportInit Display First KBC Input ClockUART2 Mode Select IR Transmission DelayOnboard FDC Controller Onboard Serial Port 1 and Onboard Serial PortParallel Port Mode, ECP Mode Use DMA and EPP Mode Select Keyboard/Mouse Power OnSupervisor Password Award Bios Setup Utility User Password IDE HDD Auto DetectionAward Bios Setup Utility Save & Exit Setup Exit Without SavingDesktop Management Interface DMI Supported SoftwaresRunning the DMI Utility Supported Softwares Using the DMI Utility Edit DMILoad DMI File Supported Softwares Add DMISave DMI File Hardware Doctor Utility Supported SoftwaresFaults Count 1 or EnableBeep Patch Utility for Windows Temperature UnitPolling Interval Error Messages Appendix a System Error MessagePost Beep System Error Message Troubleshooting Checklist Appendix B -TroubleshootingMonitor/Display Power Supply TroubleshootingFloppy Drive Troubleshooting Hard Drive Parallel PortKeyboard Troubleshooting Serial PortSystem Board