Intel CB60-BX, CB60-ZX Award Bios Setup Utility 5 PNP/PCI Configuration, Resources Controlled By

Page 42

3

Award BIOS Setup Utility

3.1.5 PNP/PCI Configuration

This section describes configuring the PCI bus system. It covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings.

ROM PCI/ISA BIOS

PNP/PCI CONFIGURATION

AWARD SOFTWARE, INC.

 

 

 

 

 

 

 

 

 

 

 

Resources Controlled By

: Auto

Assign IRQ for VGA : Enabled

 

 

 

Reset Configuration Data

: Disabled

Assign IRQ for USB

: Enabled

 

 

 

 

 

PCI Slot 1 Use IRQ

: Auto

 

 

 

 

 

 

PCI Slot 2 Use IRQ

: Auto

 

 

 

 

 

 

PCI Slot 3 Use IRQ

: Auto

 

 

 

 

 

 

PCI Slot 4 Use IRQ

: Auto

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ESC

:

Quit

− ↓ → ←

:

Select Item

 

 

 

 

F1

:

Help

PU/PD/+/-

:

Modify

 

 

 

 

F5

:

Old Values (Shift) F2

:

Color

 

 

 

 

F6

:

Load Fail-Safe Settings

 

 

 

 

 

 

F7

:

Load Optimal Settings

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The settings on the screen are for reference only. Your version may not be identical to this one.

Resources Controlled By

The Award Plug and Play BIOS has the capability to automatically configure all of the boot and Plug and Play compatible devices.

Auto The system will automatically detect the settings for you. The categories that follow will not be shown on the screen.

Manual This will allow you to set the IRQ/DMA (you have assigned your add-in card) to Legacy ISA or PCI/ISA PnP. For non-PnP ISA cards, select Legacy ISA. For PnP ISA or PCI cards, select PCI/ISA PnP.

Reset Configuration Data

Enabled The BIOS will reset the configuration data once automatically. It will then recreate a new set of configuration data.

Disabled The BIOS will not reset the configuration data.

42

Image 42
Contents CB60-BX/ZX 37400849Copyright TrademarksFCC and DOC Statement on Class B Table of Contents Appendix a System Error Messages Appendix B TroubleshootingFeatures and Specifications FeaturesIntroduction Expansion Slots ConnectorsIntroduction Desktop Management Interface DMIIrDA Interface System Health Monitor FunctionsPCI Bus Master IDE Controller USB PortsIntroduction Intelligence Package Checklist Virus ProtectionHardware Installation System Board LayoutHardware Installation DIP Switch Settings for Processors For Factory Use Only System MemoryJumper Settings for the CPU’s Front Side Bus Jumper JP2 CPU’s Front Side Bus SelectJumper Settings for Clearing Cmos Data Jumper JP3 Clear Cmos DataJumper Settings for Wake-On-Keyboard/ Wake-On-Mouse Jumper JP1 Wake-On-Keyboard/Wake-On-MouseSerial Ports 2 PS/2 Mouse and Keyboard PortsHardware Installation Parallel Ports Floppy Disk ControllerHardware Installation IDE Hard Disk Interface Adding a Second IDE Hard DriveHardware Installation USB Ports IrDA ConnectorHardware Installation CPU Fan Connector Chassis Fan ConnectorHardware Installation AGP Fan Connector SB-LINK ConnectorHardware Installation Wake-On-LAN Connector Hardware Installation Power Connector COM PW-OK 5VSBHardware Installation 14 J14 LEDs and Switches Keylock Power/Standby LED and Keylock Connector KeylockAward Bios Setup Utility Standard Cmos SetupBasic Input/Output System Award Bios Setup Utility DateTime Drive a and Drive B VideoHalt On Award Bios Setup Utility Bios Features Setup Virus WarningBoot Up Floppy Seek Quick Power On Self TestBoot Sequence CPU L1 Cache and CPU L2 CacheTypematic Delay Msec Boot Up NumLock StatusTypematic Rate Setting Typematic Rate Chars/SecChipset Features Setup OS Select for Dram 64MBHDD S.M.A.R.T. Capability System Bios Cacheable Sdram RAS-to-CAS DelayDram Data Integrity Mode CB60-BX only Video Bios CacheableMemory Hole At 15M-16M Bit I/O Recovery Time and 16 Bit I/O Recovery TimeVideo RAM Cacheable PCI 2.1 ComplianceSpread Spectrum System Health MonitorPower Management Setup Cpuv+1.5V, +3.3V, +5V, +12V, -12V PM Control by APM Power ManagementAcpi Function Video Off MethodHDD Power Down Standby ModeSuspend Mode Video Off AfterSoft-Off by PWR-BTTN PWR Lost Resume StateResume On Ring Resume On LAN Resume On AlarmTimer hhmmss Date of MonthAward Bios Setup Utility 5 PNP/PCI Configuration Reset Configuration DataResources Controlled By Assign IRQ for USB Load Fail-Safe SettingsAssign IRQ for VGA PCI Slot 1 Use IRQ to PCI Slot 4 Use IRQAward Bios Setup Utility Load Optimal Settings IDE HDD Block ModeIntegrated Peripherals Init Display First On-Chip Primary PCI IDE and On-Chip Secondary PCI IDEUSB Keyboard Support KBC Input ClockOnboard FDC Controller UART2 Mode SelectIR Transmission Delay Onboard Serial Port 1 and Onboard Serial PortParallel Port Mode, ECP Mode Use DMA and EPP Mode Select Keyboard/Mouse Power OnSupervisor Password Award Bios Setup Utility User Password IDE HDD Auto DetectionAward Bios Setup Utility Save & Exit Setup Exit Without SavingSupported Softwares Desktop Management Interface DMIRunning the DMI Utility Supported Softwares Using the DMI Utility Edit DMISupported Softwares Add DMI Load DMI FileSave DMI File Hardware Doctor Utility Supported SoftwaresEnable Faults Count 1 orBeep Temperature Unit Patch Utility for WindowsPolling Interval Appendix a System Error Message Error MessagesPost Beep System Error Message Appendix B -Troubleshooting Troubleshooting ChecklistMonitor/Display Troubleshooting Power SupplyFloppy Drive Troubleshooting Hard Drive Parallel PortTroubleshooting Serial Port KeyboardSystem Board