Intel CB60-ZX, CB60-BX manual Drive a and Drive B, Video, Halt On

Page 29

Award BIOS Setup Utility

Drive A and Drive B

These categories identify the types of floppy disk drives installed.

None

 

No floppy drive is installed

360K, 5.25 in.

5-1/4 in. standard drive; 360KB capacity

1.2M, 5.25

in.

5-1/4 in. AT-type high-density drive; 1.2MB capacity

720K, 3.5 in.

3-1/2 in. double-sided drive; 720KB capacity

1.44M, 3.5

in.

3-1/2 in. double-sided drive; 1.44MB capacity

2.88M, 3.5

in.

3-1/2 in. double-sided drive; 2.88MB capacity

Video

This category selects the type of video adapter used for the primary system monitor. Although secondary monitors are supported, you do not have to select the type in Setup.The default setting is EGA/VGA (BIOS default, Setup default).

EGA/VGA Enhanced Graphics Adapter/Video Graphics Array. For EGA,VGA, SVGA and PGA monitor adapters.

CGA 40 Color Graphics Adapter. Power up in 40-column mode. CGA 80 Color Graphics Adapter. Power up in 80-column mode.

Mono Monochrome adapter. Includes high resolution monochrome adapters.

Halt On

This category determines whether the system will stop if an error is detected during power up. The default setting is All Errors (BIOS default, Setup default).

No Errors The system boot will not stop for any errors detected. All Errors The system boot will stop whenever the BIOS detects

a non-fatal error.

All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other errors.

All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors.

All, But Disk/Key The system boot will not stop for a disk or keyboard error; it will stop for all other errors.

3

29

Image 29
Contents 37400849 CB60-BX/ZXTrademarks CopyrightFCC and DOC Statement on Class B Table of Contents Appendix B Troubleshooting Appendix a System Error MessagesIntroduction Features and SpecificationsFeatures Introduction ConnectorsExpansion Slots Desktop Management Interface DMIPCI Bus Master IDE Controller System Health Monitor FunctionsIrDA Interface USB PortsIntroduction Intelligence Virus Protection Package ChecklistSystem Board Layout Hardware InstallationHardware Installation System Memory DIP Switch Settings for Processors For Factory Use OnlyJumper JP2 CPU’s Front Side Bus Select Jumper Settings for the CPU’s Front Side BusJumper JP3 Clear Cmos Data Jumper Settings for Clearing Cmos DataJumper JP1 Wake-On-Keyboard/Wake-On-Mouse Jumper Settings for Wake-On-Keyboard/ Wake-On-Mouse2 PS/2 Mouse and Keyboard Ports Serial PortsFloppy Disk Controller Hardware Installation Parallel PortsAdding a Second IDE Hard Drive Hardware Installation IDE Hard Disk InterfaceIrDA Connector Hardware Installation USB PortsChassis Fan Connector Hardware Installation CPU Fan ConnectorSB-LINK Connector Hardware Installation AGP Fan ConnectorHardware Installation Wake-On-LAN Connector COM PW-OK 5VSB Hardware Installation Power ConnectorHardware Installation 14 J14 LEDs and Switches Keylock Keylock Power/Standby LED and Keylock ConnectorBasic Input/Output System Award Bios Setup UtilityStandard Cmos Setup Time Award Bios Setup UtilityDate Halt On Drive a and Drive BVideo Virus Warning Award Bios Setup Utility Bios Features SetupBoot Sequence Quick Power On Self TestBoot Up Floppy Seek CPU L1 Cache and CPU L2 CacheTypematic Rate Setting Boot Up NumLock StatusTypematic Delay Msec Typematic Rate Chars/SecHDD S.M.A.R.T. Capability Chipset Features SetupOS Select for Dram 64MB Dram Data Integrity Mode CB60-BX only Sdram RAS-to-CAS DelaySystem Bios Cacheable Video Bios CacheableVideo RAM Cacheable Bit I/O Recovery Time and 16 Bit I/O Recovery TimeMemory Hole At 15M-16M PCI 2.1 ComplianceSystem Health Monitor Spread Spectrum+1.5V, +3.3V, +5V, +12V, -12V Power Management SetupCpuv Acpi Function Power ManagementPM Control by APM Video Off MethodSuspend Mode Standby ModeHDD Power Down Video Off AfterResume On Ring Soft-Off by PWR-BTTNPWR Lost Resume State Timer hhmmss Resume On AlarmResume On LAN Date of MonthResources Controlled By Award Bios Setup Utility 5 PNP/PCI ConfigurationReset Configuration Data Assign IRQ for VGA Load Fail-Safe SettingsAssign IRQ for USB PCI Slot 1 Use IRQ to PCI Slot 4 Use IRQIntegrated Peripherals Award Bios Setup Utility Load Optimal SettingsIDE HDD Block Mode USB Keyboard Support On-Chip Primary PCI IDE and On-Chip Secondary PCI IDEInit Display First KBC Input ClockIR Transmission Delay UART2 Mode SelectOnboard FDC Controller Onboard Serial Port 1 and Onboard Serial PortKeyboard/Mouse Power On Parallel Port Mode, ECP Mode Use DMA and EPP Mode SelectSupervisor Password IDE HDD Auto Detection Award Bios Setup Utility User PasswordExit Without Saving Award Bios Setup Utility Save & Exit SetupRunning the DMI Utility Supported SoftwaresDesktop Management Interface DMI Edit DMI Supported Softwares Using the DMI UtilitySave DMI File Supported Softwares Add DMILoad DMI File Supported Softwares Hardware Doctor UtilityBeep EnableFaults Count 1 or Polling Interval Temperature UnitPatch Utility for Windows Post Beep Appendix a System Error MessageError Messages System Error Message Monitor/Display Appendix B -TroubleshootingTroubleshooting Checklist Floppy Drive TroubleshootingPower Supply Parallel Port Troubleshooting Hard DriveSystem Board Troubleshooting Serial PortKeyboard