Intel CB60-BX, CB60-ZX manual Troubleshooting, Power Supply, Floppy Drive

Page 60

B

Troubleshooting

The picture seems to be constantly moving.

1.The monitor has lost its vertical sync. Adjust the monitor’s vertical sync.

2.Move away any objects, such as another monitor or fan, that may be creating a magnetic field around the display.

3.Make sure your video card’s output frequencies are supported by this monitor.

The screen seems to be constantly wavering.

1.If the monitor is close to another monitor, the adjacent monitor may need to be turned off. Fluorescent lights adjacent to the monitor may also cause screen wavering.

Power Supply

When the computer is turned on, nothing happens.

1.Check that one end of the AC power cord is plugged into a live outlet and the other end properly plugged into the back of the system.

2.Make sure that the voltage selection switch on the back panel is set for the correct type of voltage you are using.

3.The power cord may have a “short” or “open”. Inspect the cord and install a new one if necessary.

Floppy Drive

The computer cannot access the floppy drive.

1.The floppy diskette may not be formatted. Format the diskette and try again.

2.The diskette may be write-protected. Use a diskette that is not write-protected.

3.You may be writing to the wrong drive. Check the path statement to make sure you are writing to the targeted drive.

4.There is not enough space left on the diskette. Use another diskette with adequate storage space.

60

Image 60
Contents CB60-BX/ZX 37400849Copyright TrademarksFCC and DOC Statement on Class B Table of Contents Appendix a System Error Messages Appendix B TroubleshootingFeatures and Specifications FeaturesIntroduction Connectors IntroductionExpansion Slots Desktop Management Interface DMISystem Health Monitor Functions PCI Bus Master IDE ControllerIrDA Interface USB PortsIntroduction Intelligence Package Checklist Virus ProtectionHardware Installation System Board LayoutHardware Installation DIP Switch Settings for Processors For Factory Use Only System MemoryJumper Settings for the CPU’s Front Side Bus Jumper JP2 CPU’s Front Side Bus SelectJumper Settings for Clearing Cmos Data Jumper JP3 Clear Cmos DataJumper Settings for Wake-On-Keyboard/ Wake-On-Mouse Jumper JP1 Wake-On-Keyboard/Wake-On-MouseSerial Ports 2 PS/2 Mouse and Keyboard PortsHardware Installation Parallel Ports Floppy Disk ControllerHardware Installation IDE Hard Disk Interface Adding a Second IDE Hard DriveHardware Installation USB Ports IrDA ConnectorHardware Installation CPU Fan Connector Chassis Fan ConnectorHardware Installation AGP Fan Connector SB-LINK ConnectorHardware Installation Wake-On-LAN Connector Hardware Installation Power Connector COM PW-OK 5VSBHardware Installation 14 J14 LEDs and Switches Keylock Power/Standby LED and Keylock Connector KeylockAward Bios Setup Utility Standard Cmos SetupBasic Input/Output System Award Bios Setup Utility DateTime Drive a and Drive B VideoHalt On Award Bios Setup Utility Bios Features Setup Virus WarningQuick Power On Self Test Boot SequenceBoot Up Floppy Seek CPU L1 Cache and CPU L2 CacheBoot Up NumLock Status Typematic Rate SettingTypematic Delay Msec Typematic Rate Chars/SecChipset Features Setup OS Select for Dram 64MBHDD S.M.A.R.T. Capability Sdram RAS-to-CAS Delay Dram Data Integrity Mode CB60-BX onlySystem Bios Cacheable Video Bios CacheableBit I/O Recovery Time and 16 Bit I/O Recovery Time Video RAM CacheableMemory Hole At 15M-16M PCI 2.1 ComplianceSpread Spectrum System Health MonitorPower Management Setup Cpuv+1.5V, +3.3V, +5V, +12V, -12V Power Management Acpi FunctionPM Control by APM Video Off MethodStandby Mode Suspend ModeHDD Power Down Video Off AfterSoft-Off by PWR-BTTN PWR Lost Resume StateResume On Ring Resume On Alarm Timer hhmmssResume On LAN Date of MonthAward Bios Setup Utility 5 PNP/PCI Configuration Reset Configuration DataResources Controlled By Load Fail-Safe Settings Assign IRQ for VGAAssign IRQ for USB PCI Slot 1 Use IRQ to PCI Slot 4 Use IRQAward Bios Setup Utility Load Optimal Settings IDE HDD Block ModeIntegrated Peripherals On-Chip Primary PCI IDE and On-Chip Secondary PCI IDE USB Keyboard SupportInit Display First KBC Input ClockUART2 Mode Select IR Transmission DelayOnboard FDC Controller Onboard Serial Port 1 and Onboard Serial PortParallel Port Mode, ECP Mode Use DMA and EPP Mode Select Keyboard/Mouse Power OnSupervisor Password Award Bios Setup Utility User Password IDE HDD Auto DetectionAward Bios Setup Utility Save & Exit Setup Exit Without SavingSupported Softwares Desktop Management Interface DMIRunning the DMI Utility Supported Softwares Using the DMI Utility Edit DMISupported Softwares Add DMI Load DMI FileSave DMI File Hardware Doctor Utility Supported SoftwaresEnable Faults Count 1 orBeep Temperature Unit Patch Utility for WindowsPolling Interval Appendix a System Error Message Error MessagesPost Beep System Error Message Appendix B -Troubleshooting Troubleshooting ChecklistMonitor/Display Troubleshooting Power SupplyFloppy Drive Troubleshooting Hard Drive Parallel PortTroubleshooting Serial Port KeyboardSystem Board