Intel GENE-8310 manual Copyright Notice

Page 2

SubCompact Board

G E N E - 8 3 1 0

 

 

Copyright Notice

This document is copyrighted, 2006. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable. However, the original manufacturer assumes no responsibility for its use, or for any infringements upon the rights of third parties that may result from its use.

The material in this document is for product information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, AAEON assumes no liabilities resulting from errors or omissions in this document, or from the use of the information contained herein.

AAEON reserves the right to make changes in the product design without notice to its users.

i

Image 2
Contents 6 Channel Audio & Mini PCI GENE-8310Intel Celeron M Processor Subcompact Board With LVDS, Ethernet SubCompact BoardCopyright Notice Acknowledgments Packing List Chapter 1 General Information ContentsChapter 2 Quick Installation Guide Appendix A Programming The Watchdog Timer Chapter 3 Award BIOS SetupChapter 4 Driver Installation IRQ Mapping Chart Appendix BI/O Information I/O Address MapChapter 1 General Information 1 General InformationChapter Multiple Display Modes Superb Performance and Controllable Power Usage1.1 Introduction Chapter 1 General InformationWide Expansion Capability AC-97 3D Surround 5.1 Channel Audio 1.2 Features48-bit Dual Channels LVDS TFT LCD 10/100Mbps Fast Ethernet Supports Type II CompactFlash Memory1.3 Specifications SystemDisplay support Wake-up function Two 5 x 2 Pin Headers Support4 USB 2.0 Ports Does not Part No. 2007831011 Printed in Taiwan JAN Quick Installation GuideChapter 2 Quick Installation Guide 2.1 Safety Precautions 2.2 Location of Connectors and Jumpers Component Side The Height of Cooling System Depends on Customer Cooling DeviceSolder Side CFD1 DIMM1The Height of Cooling System Depends on Customer Cooling Device 2.3 Mechanical DrawingComponent Side 103.510.58 3.23 8.89 0.00 72.39 0.58 114.30133.93 0.00Label Jumpers2.4 List of Jumpers FunctionConnectors 2.5 List of ConnectorsCN17 Closed 2.6 Setting JumpersOpen 2.8 LCD Voltage Selection JP2 2.10 USB2.0 Port 1 Connector CN12.7 Clear CMOS Selection JP1 2.9 COM2 RI/+5V Selection JP52.11 USB2.0 Port 2 Connector CN2 2.12 Primary IDE Hard Drive Connector CN3Name 2.13 Digital IO Connector CN4DIO Address is 801H 2.15 Serial Port COM2 Connector CN6 2.14 Front Panel CN52.16 Parallel Port Connector CN7 PinSignal 2.17 Dual Channel LVDS Connector CN82.18 4P Power Connector CN9 2.21 Audio Input/Output Connector CN12 2.19 TV-Out Connector CN102.20 DVI Connector CN11 2.24 IrDA Connector CN15 2.22 Ethernet 10/100Base-TX RJ-45 Phone Jack Connector CN132.23 External 5VSB/PWRGD Connector CN14 G E N E - 82.27 Serial Port COM1 Connector CN18 2.25 Fan Connector CN162.26 Mini-DIN PS/2 Connector CN17 2.30 Mini PCI Slot MPCI1 2.28 CRT Display Connector CN192.29 External Battery VBAT2 2.31 CompactFlash Disk Slot CFD1SubCompact Board Award BIOS Setup Chapter 3 Award BIOS SetupSystem configuration verification 3.1 System Test and InitializationAdvanced BIOS Features Entering SetupStandard CMOS Features Advanced Chipset FeaturesLoad Fail-Safe Defaults Power Management SetupPnP/PCI Configurations Load Optimized DefaultsExit Without Saving Set Supervisor/User PasswordSave and Exit Setup Driver Installation Chapter 4 Driver InstallationFollow the sequence below to install the drivers 4.1 Installation Chapter4 Drivers InstallationStep 4 - Install Realtek AC97 codec Driver Appendix A Programming the Watchdog Timer A-1 Programming the Watchdog TimerAppendix Appendix A Programming the Watchdog Timer A-2 Configuring Sequence DescriptionA.1 Programming 3 Exit the MB PnP Mode 1 Enter the MB PnP Mode2 Modify the Data of the Registers Appendix A Programming the Watchdog Timer A-4 Configure Control Index=02hWatchDog Timer Configuration Registers WatchDog Timer Time-out Value Register Index=73h, Default=00h WatchDog Timer Control Register Index=71h, Default=00hWatchDog Timer Configuration Register Index=72h, Default=00h Appendix A Programming the Watchdog Timer A-5A.2 ITE8712 Watchdog Timer Initial Program game port enable mov cl call SetLogicDevice InitialOK CALL ReadConfigurationData CMP AL,12h JNE NotInitial NeedInitial STC RET ExitConfigurationMode ENDP CheckChip PROC NEAR MOV AL,20hCALL ReadConfigurationData CMP AL,87h JNE NotInitial MOV AL,21h RET NotInitial CLC RET CheckChip ENDP ReadConfigurationData PROC NEARMOV DX,WORD PTR CSCfgPort+06h IN AL,DX RET ReadConfigurationData ENDP SetLogicDevice proc near push ax push cx xchg al,cl mov cl,07h END MainAppendix A Programming the Watchdog Timer A-10 call SuperioSetReg pop cx pop ax ret SetLogicDevice endpI/O Information Appendix B I/O Information B-1Appendix B I/O Information B-2 B.1 I/O Address MapB.2 1st MB Memory Address Map Appendix B I/O Informaion B-3 B.3 IRQ Mapping ChartB.4 DMA Channel Assignments