Intel GENE-8310 manual Drivers Installation

Page 43

4.1 Installation:

SubCompact Board	G E N E - 8 3 1 0

4.1 Installation:

Insert the GENE-8310 CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 4 in order.

Step 1 – Install Intel® INF Update for Windows 2000/XP

1.Click on the Intel® INF Update for Windows 2000/XP folder and then double click on the setup.exe

2.Follow the instructions that the window shows

3.The system will help you install the driver automatically

Step 2 – Install Intel Extreme Graphics 2 Driver

1.Click on the Intel® Extreme Graphics 2 Driver folder and then double click on the setup.exe

2.Follow the instructions that the window shows

3.The system will help you install the driver automatically

4.Please re-start your computer

Remark: You can choose the different display ways by pressing below hot key,

C+A+F1=CRT, C+A+F2=LCD, C+A+F3=TV, C+A+F4=DVI, C+A+F12=Graphic Control Panel

Step 3 – Install Intel® LAN 82562ET Driver

1.Click on the Intel® LAN 82562ET Driver folder and then double click on the setup.exe

2.Follow the instructions that the window shows

3.The system will help you install the driver automatically

Chapter4 Drivers Installation 4-3

Image 43

Contents SubCompact Board GENE-8310Intel Celeron M Processor Subcompact Board With LVDS, Ethernet 6 Channel Audio & Mini PCICopyright Notice Acknowledgments Packing List Chapter 2 Quick Installation Guide ContentsChapter 1 General Information Chapter 4 Driver Installation Chapter 3 Award BIOS SetupAppendix A Programming The Watchdog Timer I/O Address Map Appendix BI/O Information IRQ Mapping ChartChapter General InformationChapter 1 General Information 1 Chapter 1 General Information Superb Performance and Controllable Power Usage1.1 Introduction Multiple Display ModesWide Expansion Capability Supports Type II CompactFlash Memory 1.2 Features48-bit Dual Channels LVDS TFT LCD 10/100Mbps Fast Ethernet AC-97 3D Surround 5.1 Channel AudioSystem 1.3 SpecificationsDisplay 4 USB 2.0 Ports Does not Two 5 x 2 Pin Headers Supportsupport Wake-up function Chapter 2 Quick Installation Guide Quick Installation GuidePart No. 2007831011 Printed in Taiwan JAN 2.1 Safety Precautions The Height of Cooling System Depends on Customer Cooling Device 2.2 Location of Connectors and Jumpers Component SideCFD1 DIMM1 Solder Side103.51 2.3 Mechanical DrawingComponent Side The Height of Cooling System Depends on Customer Cooling Device0.00 3.23 8.89 0.00 72.39 0.58 114.30133.93 0.58Function Jumpers2.4 List of Jumpers Label2.5 List of Connectors ConnectorsCN17 Open 2.6 Setting JumpersClosed 2.9 COM2 RI/+5V Selection JP5 2.10 USB2.0 Port 1 Connector CN12.7 Clear CMOS Selection JP1 2.8 LCD Voltage Selection JP22.12 Primary IDE Hard Drive Connector CN3 2.11 USB2.0 Port 2 Connector CN2DIO Address is 801H 2.13 Digital IO Connector CN4Name 2.14 Front Panel CN5 2.15 Serial Port COM2 Connector CN62.16 Parallel Port Connector CN7 2.18 4P Power Connector CN9 2.17 Dual Channel LVDS Connector CN8PinSignal 2.20 DVI Connector CN11 2.19 TV-Out Connector CN102.21 Audio Input/Output Connector CN12 G E N E - 8 2.22 Ethernet 10/100Base-TX RJ-45 Phone Jack Connector CN132.23 External 5VSB/PWRGD Connector CN14 2.24 IrDA Connector CN152.26 Mini-DIN PS/2 Connector CN17 2.25 Fan Connector CN162.27 Serial Port COM1 Connector CN18 2.31 CompactFlash Disk Slot CFD1 2.28 CRT Display Connector CN192.29 External Battery VBAT2 2.30 Mini PCI Slot MPCI1G E N E - 8 3 1 Chapter 3 Award BIOS Setup Award BIOS Setup3.1 System Test and Initialization System configuration verificationAdvanced Chipset Features Entering SetupStandard CMOS Features Advanced BIOS FeaturesLoad Optimized Defaults Power Management SetupPnP/PCI Configurations Load Fail-Safe DefaultsSave and Exit Setup Set Supervisor/User PasswordExit Without Saving Chapter 4 Driver Installation Driver InstallationFollow the sequence below to install the drivers Chapter4 Drivers Installation 4.1 InstallationStep 4 - Install Realtek AC97 codec Driver Appendix Programming the Watchdog TimerAppendix A Programming the Watchdog Timer A-1 A.1 Programming Configuring Sequence DescriptionAppendix A Programming the Watchdog Timer A-2 2 Modify the Data of the Registers 1 Enter the MB PnP Mode3 Exit the MB PnP Mode WatchDog Timer Configuration Registers Configure Control Index=02hAppendix A Programming the Watchdog Timer A-4 Appendix A Programming the Watchdog Timer A-5 WatchDog Timer Control Register Index=71h, Default=00hWatchDog Timer Configuration Register Index=72h, Default=00h WatchDog Timer Time-out Value Register Index=73h, Default=00hA.2 ITE8712 Watchdog Timer Initial Program game port enable mov cl call SetLogicDevice InitialOK RET NotInitial CLC RET CheckChip ENDP ReadConfigurationData PROC NEAR RET ExitConfigurationMode ENDP CheckChip PROC NEAR MOV AL,20hCALL ReadConfigurationData CMP AL,87h JNE NotInitial MOV AL,21h CALL ReadConfigurationData CMP AL,12h JNE NotInitial NeedInitial STCMOV DX,WORD PTR CSCfgPort+06h IN AL,DX RET ReadConfigurationData ENDP call SuperioSetReg pop cx pop ax ret SetLogicDevice endp END MainAppendix A Programming the Watchdog Timer A-10 SetLogicDevice proc near push ax push cx xchg al,cl mov cl,07hAppendix B I/O Information B-1 I/O InformationB.2 1st MB Memory Address Map B.1 I/O Address MapAppendix B I/O Information B-2 B.4 DMA Channel Assignments B.3 IRQ Mapping ChartAppendix B I/O Informaion B-3