Intel GENE-8310 Award BIOS Setup, Driver Installation, Appendix A Programming The Watchdog Timer

Page 6

 

SubCompact Board

 

G E N E - 8 3 1 0

 

 

 

 

 

 

 

 

 

2.18

4P Power Connector (CN9)

....................................

2-16

2.19

TV-out Connector (CN10)

2-17

2.20

DVI Connector (CN11)

2-17

2.21

Audio Input/Output Connector (CN12)

2-17

2.22

Ethernet 10/100 BaseT RJ-45 Phone Jack Connector

 

(CN13)

2-18

2.23

External 5VSB/PWRGD Connector (CN14)

2-18

2.24

IrDA Connector (CN15)

2-18

2.25

Fan Connector (CN16)

2-19

2.26

Mini-DIN PS/2 Connector (CN17)

2-19

2.27

Serial Port COM1 Connector (CN18)

2-19

2.28

CRT Display Connector (CN19)

2-20

2.29

External Battery (VBAT2)

2-20

2.30

Mini PCI Slot (MPCI1)

2-20

2.31

CompactFlash Disk Slot (CFD1)

2-20

Chapter 3 Award BIOS Setup

 

 

 

 

3.1 System Test and Initialization

3-2

 

3.2 Award BIOS Setup

3-3

Chapter 4 Driver Installation

 

 

 

 

4.1 Installation

4-3

Appendix A Programming The Watchdog Timer

 

 

 

A.1 Programming

A-2

 

A.2 IT8712 Watchdog Timer Initial Program

A-6

v

Page 5 Page 7
Image 6
Page 5 Page 7
Contents 6 Channel Audio & Mini PCI GENE-8310Intel Celeron M Processor Subcompact Board With LVDS, Ethernet SubCompact BoardCopyright Notice Acknowledgments Packing List Contents Chapter 2 Quick Installation GuideChapter 1 General Information Chapter 3 Award BIOS Setup Chapter 4 Driver InstallationAppendix A Programming The Watchdog Timer IRQ Mapping Chart Appendix BI/O Information I/O Address MapGeneral Information ChapterChapter 1 General Information 1 Multiple Display Modes Superb Performance and Controllable Power Usage1.1 Introduction Chapter 1 General InformationWide Expansion Capability AC-97 3D Surround 5.1 Channel Audio 1.2 Features48-bit Dual Channels LVDS TFT LCD 10/100Mbps Fast Ethernet Supports Type II CompactFlash Memory1.3 Specifications SystemDisplay Two 5 x 2 Pin Headers Support 4 USB 2.0 Ports Does notsupport Wake-up function Quick Installation Guide Chapter 2 Quick Installation GuidePart No. 2007831011 Printed in Taiwan JAN 2.1 Safety Precautions 2.2 Location of Connectors and Jumpers Component Side The Height of Cooling System Depends on Customer Cooling DeviceSolder Side CFD1 DIMM1The Height of Cooling System Depends on Customer Cooling Device 2.3 Mechanical DrawingComponent Side 103.510.58 3.23 8.89 0.00 72.39 0.58 114.30133.93 0.00Label Jumpers2.4 List of Jumpers FunctionConnectors 2.5 List of ConnectorsCN17 2.6 Setting Jumpers OpenClosed 2.8 LCD Voltage Selection JP2 2.10 USB2.0 Port 1 Connector CN12.7 Clear CMOS Selection JP1 2.9 COM2 RI/+5V Selection JP52.11 USB2.0 Port 2 Connector CN2 2.12 Primary IDE Hard Drive Connector CN32.13 Digital IO Connector CN4 DIO Address is 801HName 2.15 Serial Port COM2 Connector CN6 2.14 Front Panel CN52.16 Parallel Port Connector CN7 2.17 Dual Channel LVDS Connector CN8 2.18 4P Power Connector CN9PinSignal 2.19 TV-Out Connector CN10 2.20 DVI Connector CN112.21 Audio Input/Output Connector CN12 2.24 IrDA Connector CN15 2.22 Ethernet 10/100Base-TX RJ-45 Phone Jack Connector CN132.23 External 5VSB/PWRGD Connector CN14 G E N E - 82.25 Fan Connector CN16 2.26 Mini-DIN PS/2 Connector CN172.27 Serial Port COM1 Connector CN18 2.30 Mini PCI Slot MPCI1 2.28 CRT Display Connector CN192.29 External Battery VBAT2 2.31 CompactFlash Disk Slot CFD1SubCompact Board Award BIOS Setup Chapter 3 Award BIOS SetupSystem configuration verification 3.1 System Test and InitializationAdvanced BIOS Features Entering SetupStandard CMOS Features Advanced Chipset FeaturesLoad Fail-Safe Defaults Power Management SetupPnP/PCI Configurations Load Optimized DefaultsSet Supervisor/User Password Save and Exit SetupExit Without Saving Driver Installation Chapter 4 Driver InstallationFollow the sequence below to install the drivers 4.1 Installation Chapter4 Drivers InstallationStep 4 - Install Realtek AC97 codec Driver Programming the Watchdog Timer AppendixAppendix A Programming the Watchdog Timer A-1 Configuring Sequence Description A.1 ProgrammingAppendix A Programming the Watchdog Timer A-2 1 Enter the MB PnP Mode 2 Modify the Data of the Registers3 Exit the MB PnP Mode Configure Control Index=02h WatchDog Timer Configuration RegistersAppendix A Programming the Watchdog Timer A-4 WatchDog Timer Time-out Value Register Index=73h, Default=00h WatchDog Timer Control Register Index=71h, Default=00hWatchDog Timer Configuration Register Index=72h, Default=00h Appendix A Programming the Watchdog Timer A-5A.2 ITE8712 Watchdog Timer Initial Program game port enable mov cl call SetLogicDevice InitialOK CALL ReadConfigurationData CMP AL,12h JNE NotInitial NeedInitial STC RET ExitConfigurationMode ENDP CheckChip PROC NEAR MOV AL,20hCALL ReadConfigurationData CMP AL,87h JNE NotInitial MOV AL,21h RET NotInitial CLC RET CheckChip ENDP ReadConfigurationData PROC NEARMOV DX,WORD PTR CSCfgPort+06h IN AL,DX RET ReadConfigurationData ENDP SetLogicDevice proc near push ax push cx xchg al,cl mov cl,07h END MainAppendix A Programming the Watchdog Timer A-10 call SuperioSetReg pop cx pop ax ret SetLogicDevice endpI/O Information Appendix B I/O Information B-1B.1 I/O Address Map B.2 1st MB Memory Address MapAppendix B I/O Information B-2 B.3 IRQ Mapping Chart B.4 DMA Channel AssignmentsAppendix B I/O Informaion B-3
Top Page Image Contents