Intel manual Intel Server Chassis SR1450 User Guide, TP01604

Page 35

TP01604

Hardware Installations and Upgrades

7.Open the connector on the rear of the floppy drive by pulling up on the connector cover. See letter “A” in the figure below.

8.Insert one end of the 26-pin floppy drive flat flex cable end into the connector. See letter “B” in the figure below.

9.Push down on the connector cover to lock the cable into place. See letter “C” in the figure below.

A

B

C

TP01604

Figure 21. Installing Floppy Flat Flex Cable to a Floppy Drive

10.Connect the opposite end of the floppy flex cable to the matching connector on the interposer board. See letter “A” in the figure below.

11.Install floppy interposer board to floppy tray by inserting the left side into the tray slot (See Letter “B” in the figure below) and securing the other side with a screw (See letter “C” in the figure below).

12.Install floppy drive into slimline drive bay until it clicks into place.

Figure 22. Installing the Floppy Drive Interposer Board

Intel® Server Chassis SR1450 User Guide

35

Image 35

Contents Order Number: C95452-002 Intel Server Chassis SR1450 User GuideDisclaimer Manual Organization PrefaceAbout this Manual Product Contents, Order Options, and Accessories ƒRiser option, choose one •Full-height PCI-Xriser Additional Information and Software Intended Uses Safety InformationEMC Testing Emissions DisclaimerWarnings Consignes de sécurité Safety CautionsWichtige Sicherheitshinweise 重要安全指导2 Hardware Installations and Upgrades Contents1 Server Chassis Features Regulatory and Compliance Information Intel Server Issue Report FormWarranty Equipment Log and WorksheetsFigures Tables Figure 1. Intel Server Chassis SR1450 1 Server Chassis FeaturesDescription Table 1. Server Chassis FeaturesServer Chassis Features FeatureTable 1. Server Chassis Features continued Internal Components Component IdentificationFunction Standard Control PanelA B C D E F G H I J K CalloutI H G Intel Local Control PanelAB C D E F N M L K JFigure 5. Chassis Back Back Panel FeaturesFigure 4. Intel Local Control Panel Features NOTES Peripheral Devices Front FeaturesHard Disk Drives Intel Management Module Advanced Management OptionsFloppy / CD-ROM / DVD-ROMSlimline Carriers Front Bezels Rack-MountedSystemsSystem References 2 Hardware Installations and UpgradesBefore You Begin Tools and Supplies NeededRemoving the Chassis Cover Removing and Installing the Chassis CoverFigure 8. Installing the Chassis Cover Installing the Chassis CoverRemoving the Front Bezel Removing and Installing the Front BezelInstalling the Front Bezel Removing and Installing the Processor Air DuctFigure 13. Removing the Processor Air Duct Installing the Processor Air DuctRemoving the Processor Air Duct TP01598 Figure 15. Installing the Processor Air DuctFigure 14. Preparing the Processor Air Duct TP01597Removing a SATA or SCSI Hot-swapHard Disk Drive Installing and Removing a Hard Disk DriveB A B Installing a SATA or SCSI Hot-swapHard Disk DriveIntel Server Chassis SR1450 User Guide TP01603 Installing a Floppy Drive into Slimline BayTP01604 TP01606 Removing a Floppy Drive from the Slimline BayTP01609 TP01323 C AB 5.Remove cables from the interposer board Installing or Removing a CD-ROMor DVD-ROMDrive TP01614 Installing and Removing a PCI Riser Card Installing a PCI Riser Card 10.Release the blue locking lever Removing a PCI Riser Card Installing a PCI Add-inCard Installing and Removing a PCI Add-inCardTP01617 A B D CRemoving a PCI Add-inCard TP01619 Replacing the Standard Control PanelReplacing the Intel Local Control Panel 8.If using a bezel with the Local Control Panel, change out the LCP plastic front panel on the replacement control panel. If you are not using the optional bezel, make sure the back half of the tray is secured in the “shortened” position Replacing System Fans Replacing the Single System PCI Fan 8.Connect the fan into the fan connector Installing the Power Supply Air Duct Removing the Power Supply Air DuctFigure 42. Removing a Power Supply Fan Module Replacing a Power Supply Fan ModuleReplacing the Power Distribution Board 19.Reconnect the power supply fans A B B Removing a Hot-SwapPower Supply Replacing the Hot-SwapPower SupplyInstalling a Hot-SwapPower Supply system or wall outlet Removing the SATA or SCSI Backplane Installing the SATA or SCSI Backplane 8.Connect the following cables to the backplane Cable Routing Technical ReferenceTP01612 A B E C DTable 3. SATA Cable Routing Reference Technical Reference520-WSingle Power Supply Output Voltages Power Supply Specifications520-WSingle Power Supply Input Voltages Table 5. Environmental Specifications System Environmental SpecificationsItem Equipment Log and WorksheetsEquipment Log Date InstalledCurrent Usage Calculating Power UsageWorksheet, Calculating DC Power Usage V X A = W Table 7. Power Usage WorksheetVoltage level and total current Total WattsProduct EMC Compliance – Class A Compliance Product Safety ComplianceRegulatory and Compliance Information Product Regulatory ComplianceProduct Regulatory Compliance Markings Certifications / Registrations / DeclarationsFCC USA Electromagnetic Compatibility NoticesEnglish translation of the notice above Industry Canada ICES-003Europe CE Declaration of Conformity Korean RRL Compliance VCCI JapanBSMI Taiwan Regulated Specified Components Telephone Getting HelpWorld Wide Web Email Address Intel Server Product Intel Server Issue Report FormBoard / Chassis Information Date Submitted Company Name Contact NameHard Drive Information Operating System Version Service Pack #Operating System Information Peripheral InformationComplete Problem Description Page Products WarrantyLimited Warranty for Intel Chassis Subassembly Extent of Limited WarrantyLimitations of Liability Warranty Limitations and ExclusionsReturning a Defective Product How to Obtain Warranty ServiceTelephone Support