Tascam CC-222MKII owner manual Cassette operations-Recording tapes from the Phono deck

Page 18

3 – Cassette operations—Recording tapes from the PHONO deck

The dubbing stops when playback reaches the end of the CD, or when the tape reaches the end of its run (one side in the case of single-sided (u) reverse mode, both sides in the j reverse mode), which- ever comes first.

Note that if the tape is set to auto-reverse, and the last item recorded on one side of a tape was not com- pletely recorded before the tape was reversed, that item will be automatically repeated.

Also note that when the tape automatically reverses, eight seconds are used as non-recorded time at the beginning of the second side (the tape is in record

mode, but the CD does not play back), again to allow for leader tape at the start of the cassette.

The dubbing process can also be stopped manually with the STOP key of the cassette deck or the CD deck. All other transport keys are disabled.

NOTE

Dubbing is not possible if: a cassette is not loaded, or a CD is not loaded. It is not possible if the cassette is write-protected, or if the CD is a recordable disc which does not currently have any material recorded on it.

It is also not possible to enter the dubbing mode if the tape is not in stop or record ready mode, or if the CD is not in stop or pause mode.

Dubbing to tape from the middle of a CD

The above procedure describes the playback and recording from the start of a disc (or the start of a programmed playback list).

To record from a point other than the ones above:

1Locate the disc to the point where the play- back is to start.

2Press the disc PAUSE key to pause playback at the point where the playback is to start.

3If recording is to start at the beginning of the cassette, make sure the cassette is stopped, otherwise, locate the cassette to the appropri- ate position where recording is to start, and enter record ready mode.

NOTE

Using the headphones with the MONITOR switch set to MIX will help here.

4Press the DUB 2 key. Playback starts on the disc, and recording starts on the cassette.

Bypassing the INPUT level for dubbing

The INPUT control can be bypassed so that it has no effect when dubbing, in the following way:

1Press the MENU key until the DUB>VOL item appears.

2Turn the dial to select either THRU (the con- trol is bypassed and disabled) or ON (the control is enabled).

NOTE

This setting applies only to dubbing procedures, not to other recordings.

It is not possible to make this menu setting (or any other menu settings) when dubbing is actually taking place.

Recording tapes from the PHONO deck

To record from an external record deck connected through the RIAA PHONO inputs:

1Prepare for recording as described above (load a tape, set the REV MODE, etc.).

2Press the MENU key until the PHONO > xxxx menu item is shown.

If the display does not show PHONO > TAPE, turn the MULTI DIAL (or press the

SKIP keys on the remote control) until it does

and press the MULTI DIAL (or ENTER on the remote control unit).

3Press the PHONO key H. The PHONO indica- tor lights on the display.

If the tape is currently in stop mode, the tape rewinds, and the deck enters record ready mode (about eight seconds from the start of the cassette, to allow for leader tape).

If the tape deck is already in record ready mode, it will remain in record ready mode.

18 TASCAM CC-222MKII Owner’s Manual

Page 17 Page 19
Image 18
Page 17 Page 19
Contents CD Recorder/Cassette Deck Important Safety Precautions Important Safety Instructions Safety Information Contents Some notes and precautions Supplied accessoriesIntroduction Environmental considerations Introduction-Some notes and precautionsRack-mounting the unit Beware of condensationAbout tapes Introduction-FinalizingFinalizing About CD-R and CD-RW discsRecordable discs Handling of compact discsAdditional notes with regard to CD-R and CD-RW discs Use of the remote control unit Never use a stabilizer or printable discsRecommended media Introduction-About this manual About this manualFeatures and controls Monitor TAPE/MIX/DISC switch Features and controls-Rear panel featuresRear panel features Phones jack and volume controlFeatures and controls-Remote control features Remote control featuresNumber keys 0 through 10, +10, Cassette operations Playback operationsContinuous tape/CD playback Cassette operations-Recording operations Recording operationsDubbing tapes from the CD deck Dubbing to tape from the middle of a CD Cassette operations-Recording tapes from the Phono deckRecording tapes from the Phono deck Bypassing the Input level for dubbingCassette operations-Other recording features Other recording featuresOther tape functions and features Cassette operations-Other tape functions and features Fast forward and rewindSearch keys Time display modes CD playerSimple playback operations Track searchCD player-Playback modes Playback modesProgrammed order playback Repeat play Setting the a and B repeat pointsCD player-Repeat play Intro checkTimer playback CD player-Auto spacingAuto spacing Input selection Signal volumeRecording CDs Input monitoringRecording CDs-Basic recording Basic recordingFrequency conversion Recording CDs-Dubbing from tape to disc Dubbing from tape to discRecording CDs-From the Riaa Phono inputs From the Riaa Phono inputsDubbing to CD from the middle of the tape Advanced recording Setting the trigger levelRecording CDs-Advanced recording Synchronized recordingSync recording start Sync recording stopAutomatic track division Rec mute functionFade-in and fade-out To perform a fade-inTo perform a fade-out Unfinalizing CD-RW discs After recordingErasing Erasing tracksAfter recording-Erasing Erasing a whole discRefreshing a disc After recording-Erasing Reference and specifications TroubleshootingMenu items Reference and specifications-Menu itemsSpecifications CD recorder sectionReference and specifications-Specifications Phono input and headphonesCassette recorder section Tape maintenance Reference and specifications-Dimensional drawingDimensional drawing General specificationsCC-222@#
Related manuals
Manual 2 pages 55.43 Kb

CC-222MKII specifications

The Tascam CC-222MKII is a versatile and reliable combination deck that has been designed for professional audio applications. Combining the best of both worlds, this deck features a high-quality CD player and a cassette recorder, making it an ideal solution for musicians, broadcasters, and sound engineers. One of the main features of the CC-222MKII is its ability to play and record CDs as well as standard cassette tapes, which provides users with flexibility in audio formats.

The CD player in the CC-222MKII is compatible with various disc formats, including CD-R and CD-RW, allowing users to play back personalized audio compilations or recordings. Tascam has integrated a high-performance DAC (Digital to Analog Converter) within the unit, which ensures accurate sound reproduction with minimal distortion. Additionally, the player accommodates seamless playback, so users can easily transition between tracks or scan through content, enhancing the overall listening experience.

In terms of cassette functionality, the CC-222MKII offers a built-in cassette deck that utilizes a high-quality transport mechanism. This ensures smooth and reliable tape playback and recording. The deck features both playback and record capabilities for standard compact cassettes, with a user-friendly interface making it easy to navigate controls and manage audio content.

The Tascam CC-222MKII also incorporates several crucial technologies to support its functionality. One notable feature is the built-in A/D (analog to digital) and D/A (digital to analog) converters, which facilitate high-quality recording and playback. Furthermore, the unit includes a range of input options, including XLR and RCA connectors, allowing users to connect external microphones, mixers, or other audio equipment.

Another key characteristic of the CC-222MKII is its ease of use. The deck is equipped with a large LCD display that provides clear information about the current playing track, time elapsed, and other essential data. The intuitive layout and handling make it accessible for both beginners and seasoned professionals.

Moreover, the durable construction of the Tascam CC-222MKII ensures longevity and reliability in various settings, whether in a studio environment or on the road. Its compact design allows for easy integration into any audio setup, making it a popular choice for a wide range of users seeking versatility and performance in an all-in-one audio solution.
Top Page Image Contents