Lenovo 3000 J Series manual Connecting the first CD drive or DVD drive

Page 50

9.Install the drive into the bay. Align the screw holes and install four screws to secure the drive.

10.A hard disk drive requires two cables; a power cable that connects to the power supply and a signal cable that connects to the system board.

The steps to connect a drive are different depending on the type of drive you are connecting. Use one of the following procedures for your drive connection.

Connecting the first CD drive or DVD drive

1.Locate the three-connector signal cable that comes with your computer or with the new drive.

2.Locate the secondary IDE connector on the system board. See “Identifying parts on the system board” on page 21.

3.Connect one end of the signal cable to the drive and the other to the secondary IDE connector on the system board. To reduce electronic noise, use the connectors at the end of the cable only.

4.Your computer has extra power connectors for additional drives. Connect a power connector to the drive.

Connecting an additional CD drive or DVD drive

An additional drive can be connected to either the primary IDE or secondary IDE connector.

1.Locate an available IDE connector on the three-connector signal cable attached to either the primary IDE or secondary IDE connector on the system board. See “Identifying parts on the system board” on page 21.

32User Guide

Image 50
Contents User Guide Lenovo 3000 J Series Page Lenovo 3000 J Series Page Contents Getting information, help Important safety information Conditions that require immediate actionGeneral safety guidelines Service and upgradesPower cords and power adapters Static electricity preventionViii User Guide Plugs and outlets Voltage-selection switchExtension cords and related devices Heat and product ventilation External devicesBatteries Operating environment To connect To disconnect Electrical current safety informationLithium battery notice Modem safety information Laser compliance statementCleaning and maintenance Power supply statementData safety Additional safety informationIntroduction Xvi User Guide Glare and lighting Arranging your workspaceComfort Air circulation Electrical outlets and cable lengthsSetting up your computer Connecting your computerUser Guide Setting up your computer User Guide 1394 User Guide Completing important tasks Turning on powerFinishing the software installation Updating your antivirus software Installing other operating systemsUpdating your operating system Shutting down the computerInstalling options FeaturesMemory Input/output features Available options Handling static-sensitive devices SpecificationsTools required Installing external options Locating the connectors on the front of your computer Locating the connectors on the rear of your computer Connector Description Obtaining device drivers Removing the cover Locating components Identifying parts on the system boardUser Guide Installing options Installing memory What to do nextInstalling adapters Secure the adapter with the screw as shown Installing internal drives Drive specificationsUser Guide Installing a drive User Guide Installing options Connecting the first CD drive or DVD drive Installing security features Connecting a serial ATA hard disk drivePadlock loop Password protectionChanging the battery Installing options Erasing a lost or forgotten password clearing Cmos Replacing the cover and connecting the cables User Guide Recovering software Creating and using the Product Recovery discPerforming backup and recovery operations Using the Rescue and Recovery workspace Creating and using rescue media Creating and using a Recovery Repair diskette To create rescue media, do the followingRecovering or installing device drivers Setting a rescue device in the startup sequence Solving recovery problemsUser Guide Viewing and changing settings Using the Setup UtilityStarting the Setup Utility program Using passwordsAdministrator Password Password considerationsUser Password Setting, changing, and deleting a passwordSelecting a temporary startup device Using Security Profile by DeviceSelecting a startup device Changing the startup device sequence Advanced settingsExiting from the Setup Utility program Updating system programs Using system programsUpdating flashing Bios from a diskette User Guide Symptom Action Troubleshooting and diagnosticsBasic troubleshooting Diagnostic programs PC-Doctor for Windows PC-Doctor for DOSCreating diagnostic diskettes Optical mouse Cleaning the mousePC-Doctor for Windows PE Non-optical mouse Troubleshooting and diagnostics User Guide Online Books folder Getting information, help, and serviceInformation resources Lenovo CareAccess Help Warranty and safetyCalling for service Help and serviceUsing the documentation and diagnostic programs Using other services Purchasing additional servicesAppendix A. Manual modem commands Basic AT commandsSet Tone Dial as default Low speaker volumeSet Pulse dial as default Internal speaker on until carrier detectedExtended AT commands MNP/V.42/V.42bis/V.44 commands Fax Class 1 commands Fax Class 2 commandsVoice commands Appendix A. Manual modem commands User Guide Appendix B. Notices Television output notice TrademarksIndex 14, 22, 23 Page Part Number