Tascam CC-222MK Disc operations, Simple playback operations, Time display modes, Track search

Page 16

4- Disc operations

Simple playback operations

WARNING

If you are monitoring using headphones, first adjust the level control to low on the unit, then connect to the PHONES jack before playing back. This will pre- vent any possible damage to your hearing.

1Press the OPEN/CLOSE key to open the disc tray.

2Discs should be inserted in the tray with the label uppermost.

3Press the OPEN/CLOSE key to close the tray.

When a disc is loaded into the unit, the display briefly shows TOC Reading., with a flashing period as the unit determines the contents of the disc. When the TOC has been read, the display shows (at the left of the dis- play) one of the following:

4Press the PLAY key to start playback

5 Press the STOP key to stop playback

6Press the PAUSE key to pause playback tempo- rarily.

To resume playback, press the PAUSE key again or the PLAY key.

The track number indicators at the bottom of the dis- play light, to show the available tracks playing back. If there are thirteen tracks on the disc, for example, indicators 1 through 13 will light. If there are more than 20 tracks on the disc, “OVER” will light at the end of the track number indicators.

CD

Commercial pre-recorded CD

CD-R/CD-RW

Finalized CD-R or CD-RW

CD-R, NO TOC

CD-R which has yet to be finalized

CD-RW, NO TOC

CD-RW which has yet to be finalized

Time display modes

When playing back a CD, or when in standby mode, there are four different time display modes.

In each mode, the current track number is given, fol- lowed by the time, as given below, e.g.

10Tr 0:48

Press the DISPLAY key to cycle through these time dis- play modes, as described here:

Display shows

Meaning

TOTAL

Total elapsed time of the disc

TOTAL REMAIN

Time remaining of the current disc

[blank]

Elapsed time of the current track

REMAIN

Time remaining of the current track

NOTE

If the Program playback has been selected (see ”Program playback” on page 17), the elapsed time and total remaining time refer to the programmed material, not the whole disc.

Track search

Use the MULTI DIAL (or the SKIP keys on the remote control unit) to jump forward or backward by one track at a time, as shown on the display.

Note that going forward from the last track of the disc will “wrap round” to track 1, and going backward from the first track of the disc will “wrap round” to the last track of the disc.

It is also possible to use the number keys on the remote control unit to jump directly to a particular track:

1To play tracks 1 through 9, simply press the ap- propriate key (1 through 9).

2To play a track whose number is higher than 9, press the +10 key an appropriate number of times to set the“ tens” digit of the track number,

followed by a single key to set the“ units” digit. For example:

Track 13 = +10, 3

Track 30 = +10, +10, +10, 0

NOTE

On the remote control unit only, the search keys can be used to ”fast-forward” and ”fast-rewind” through the disc.

16 TASCAM CC-222MKIII

Image 16
Contents CC-222MK$ Important Safety Precautions Important Safety Instructions Safety Instructions Optical pickupContents Supplied accessories IntroductionSome notes, precautions and environmental considerations Rack-mounting the unitBeware of condensation Never use a stabilizer or printable discsAbout CD-R and CD-RW discs Handling of compact discsFinalizing About tapesAbout this manual Recordable discsUse of the remote control unit BatteriesFeatures of the CC-222MK$ Front panelRear panel Display RC-222 Remote control unit Menu configuration Menu operationDisc operations Simple playback operationsTime display modes Track searchRandom playback Playback modesProgram playback Intro check Auto spacingRepeat playback To B repeat playbackDirectory playback setting Playing back MP3 filesSignal volume Recording CDsInput selection Input monitoringBasic recording Turn the Multi dial to set the value on or OFFRecording to disc from the Riaa Phono inputs Time display while recordingPlaying back tracks Restricting the number of tracksDubbing to CD from the middle of the tape Dubbing from tape to discBypassing the Input level for dubbing Using the trigger level Setting the trigger levelAdvanced recording Synchronized recording Automatic track divisionManually divide track Rec mute function Fade-in and fade-outCopy-protection Erasing After recordingUnfinalizing CD-RW discs Erasing a whole disc Erasing tracksRefreshing a disc Playback operations Cassette operationsContinuous tape/CD playback Recording operations Dubbing tapes from the CD deckRecording tapes from the Phono deck Dubbing to tape from the middle of a CDOther recording features Other tape functions and featuresError messages Reference and specificationsMessages displayed during normal operation CD recorder section SpecificationsCassette recorder section Phono input and headphones Dimensional drawingGeneral specifications CC-222MK$