Sanyo WTC500AL owner manual Slant setting, On start

Page 57

Setting

Select one of the following options:

Ready

When the lamp has been fully cooled

 

down, the POWER indicator changes to fast

 

blinking. In this condition, the projection

 

lamp can be turned on if the input signal

 

is reconnected or any button on the top

 

control or remote control is pressed.

Shut down

When the lamp has been fully cooled down,

 

the power will be turned off.

Off

Power management function is off.

✔Note:

• Factory default is “Ready: 5 min.”

On start

When this function is set to “On,” the projector will be automatically turned on just by connecting the AC power cord to a wall outlet.

✔Note:

•Be sure to turn off the projector properly (see “Turning Off the Projector” on page 25). If the projector is turned off in the incorrect sequence, the On start function does not work properly.

•When the Standby mode is set to “Eco“ in the Setting, the On start funcion is disabled. (p.56)

•The On start function may not operate if you unplug the AC power cord and connect it immediately.

Power management

Press the SELECT button at Power management and this dialog box appears. Use the Point 7 8 buttons to choose one of the three options.

Press the Point d button to select the timer, and then use the Point 7 8 buttons to set timer.

Slant

This function is used to set the cooling fans’ operation to the projector’s setting environment. Set this function properly in accordance with the projector’s installation method. Otherwise, the cooling fans will not work properly and that causes malfunctions of the projector and decreases the lamp life.

Select the projector’s installation condition from the following options:

Off .....When using the projector within the range of the upward/

downward inclination of ±70º and +110º~ +180º, -110º~ -180º to the horizontal plane.

L1 ......When using the projector within the range of the upward/

downward inclination of +70º~+110º to the horizontal plane.

L2 ......When using the projector within the range of the upward/

downward inclination of -70º~ -110ºto the horizontal plane.

L3 ......When using the projector within the range of the upward/

downward inclination of ±70º to the horizontal plane and the ceiling function is set to “On”.

L4 ......When using the projector within the range of the upward/

downward inclination of +110º~+180º, -110º~ -180º to the horizontal plane and the ceiling function is set to “Off”.

Slant setting

+70°

UP

+0°UP -0°

UP

-70°

UP

L1

L2

UP

+110°

“L4” at Ceiling “Off”

UP

“Off” at Ceiling “On”

 

 

+180°

UP

 

 

-180°

UP

“L3” at Ceiling “On”

 

“Off” at Ceiling “Off”

-110°

 

57

Page 56 Page 58
Image 57
Page 56 Page 58
Contents
Model PLC-WTC500AL Features and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Top Control Air CirculationPositioning Precautions Installing the Projector in Proper DirectionsTransporting the Projector Moving the ProjectorAC Power Cord for the United States and Canada AC Power Cord for the United KingdomCompliance Part Names and Functions FrontBack Side Terminal 1R/C Jack 0USB Connector Series BTop Control Remote Control @2RESET/ON/ALL-OFF switch 4P-TIMER button5D..ZOOM button 6ZOOM buttonWired Remote Control Remote Control Battery InstallationRemote Control Code Adjustable Feet InstallationLens Installation Removing the lensAttaching the lens to the projector DVI Connecting to a Computer Digital and Analog RGBRCA Hdmi VGA Cables used for connectionMonitor OUT and Audio OUT Specifications Connecting for Audio SignalProjector side AC outlet side Connecting the AC Power CordBasic Operation What is PIN code?Turning On the Projector Enter a PIN codeTurning Off the Projector How to Operate the On-Screen Menu Remote ControlOn-Screen Menu Menu Bar Focus Adjustment Zoom AdjustmentLens Shift Adjustment Operating with Projector ControlSound Adjustment Direct OperationMenu Operation Operating with Remote Control PIP button Timer buttonPIP VOL.. button Shutter buttonLaser Pointer Function Pointer FunctionSpotlight Presentation Pointer button Wireless Mouse OperationRemote Control button operation Remote Control OperationInput Selection InputInput Menu Input Source SelectionRGB PC analog RGB Scart Video ComponentVideo or S-video Video System SelectionComponent AV System Menu Video or S-videoComputer System Selection Computer AdjustmentSelecting Computer System Manually PC System MenuPC Adjust Menu Auto PC AdjustmentTo store adjustment parameters Auto PC AdjManual PC Adjustment To store the adjusted data To clear the adjusted dataImage Level Selection Image Level SelectionImage Menu Image Adjustment Image AdjustmentImage Adjust Menu Gamma SharpnessNoise reduction ProgressiveTo reset the adjusted data, select Reset and press Screen Adjustment Screen AdjustmentScreen Menu KeystoneNormal Screen Size Adjustment Computer SignalsTrue FullFor zooming in and out the images Digital zoom +Digital zoom Screen Size Adjustment Video, Component Signals ZoomWide Setting SettingSetting Menu Language LogoLogo PIN code lock CaptureCapture Logo PIN code lockChange the Logo PIN code lock setting Enter a Logo PIN codeChange the Logo PIN code Background Picture in Picture When selecting Lamp1/2 mode Lamp mode Timer setting Lamp life control Lamp controlPointer Power management Standby modeDisplay DisplaySlant setting On startSlant Shutter Key lock Security Key lock and PIN code lock settingsChange the PIN code lock setting Change the PIN code lock settingPIN code lock Enter a PIN codeChange the PIN code Change the PIN codeTest pattern Factory default Factory defaultFilter Instructions Maintenance and CareReplacing the Filter Cartridge Scroll counter Filter counterLamp Mode Changeover Lamp 1/2 Replace IndicatorsAuto Lamp Selection System Lamp Status DisplayLamp Replacement Replacement Lamp Type No POA-LMP125 Service Parts No 342Model No.. of your projector Then check the matters below Cleaning the Projector Cabinet Cleaning the Projection LensProblem TroubleshootingNo power AppendixDuring the operation Setting does not remain after Auto PC adjustment functionTurning off power Power management function doesWired remote control does not Remote Control doesWireless Mouse function does Indicator blinks or lightsInput Menu TreeSystem Image SystemPC Adjust Information ScreenSound Setting Projector is operating normally Indicators and Projector ConditionImmediately Projector is detecting abnormal conditionIf the Filter counter reached a time set in the timer ON-SCREEN Resolution Compatible Computer Specifications59.940 List of Picture in Picture Monitor Output at the PIP modeTechnical Specifications Optional Parts PJ Link Notice USB Connector Series B Configurations of TerminalsOutput Terminal D-sub 9 pinLogo PIN Code Lock No PIN Code Number MemoDimensions KV5AM
Top Page Image Contents