Sanyo WTC500AL owner manual Lamp Replacement, Top Control

Page 67

Maintenance and Care

Lamp Replacement

When the total lighting time of a Projection Lamp reaches the recommended total hours of use, the Lamp replacement icon appears on the screen and LAMP 1 / 2 REPLACE indicator lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP 1 / 2 REPLACE indicator should light is depending on the lamp mode.

Top Control

LAMP 1/2 REPLACE indicators

Lamp replacement icon

✔Note:

•The Lamp replacement icon will not appear when the Display function is set to “Off” (p.56), or during “Freeze” (p.30).

CAUTION

Allow a projector to cool for at least 45 minutes before you open the Lamp cover. The inside of the projector can become very hot.

CAUTION

For continued safety, replace with a lamp of the same type lamp. Do not drop the lamp or touch the glass bulb! The glass can shatter and may cause injury.

CAUTION

When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp maybe broken. If replacing the lamp of a projector which has been installed on the ceiling, you should always assume that the lamp is broken, and you should stand to the side of the lamp cover, not underneath it. Remove the lamp cover gently. Small pieces of glass may fall out when the lamp cover is opened. If pieces of glass get into your eyes or mouth, seek medical advice immediately.

Follow these steps to replace the lamp.

1

Check the number of lamp to be replaced on the Lamp

Status Display or the LAMP 1/2 REPLACE indicators

 

and replace the lamp.

2

Turn off the projector and unplug the AC power cord.

 

Let the projector cool for at least 45 minutes.

3

Remove the screw that secures the lamp cover with a

coin, and then open the lamp cover.

4

Lift the lamp out of the projector by using the handle.

5

Replace the lamp with a new one. Make sure that

the lamp is set properly. Put the lamp cover back and

secure it with the screw.

✔Note:

•After lamp replacement, make sure to check the Lamp mode (p.53).

Lamp cover

Screw

Lamp 1

Handle

Lamp 2

67

Page 66 Page 68
Image 67
Page 66 Page 68
Contents
Model PLC-WTC500AL Features and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Top Control Air CirculationPositioning Precautions Installing the Projector in Proper DirectionsTransporting the Projector Moving the ProjectorAC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Front Part Names and FunctionsBack Side Terminal 1R/C Jack 0USB Connector Series BTop Control Remote Control 6ZOOM button 4P-TIMER button@2RESET/ON/ALL-OFF switch 5D..ZOOM buttonWired Remote Control Remote Control Battery InstallationRemote Control Code Adjustable Feet InstallationRemoving the lens Lens InstallationAttaching the lens to the projector DVI Connecting to a Computer Digital and Analog RGBRCA Hdmi VGA Cables used for connectionMonitor OUT and Audio OUT Specifications Connecting for Audio SignalProjector side AC outlet side Connecting the AC Power CordEnter a PIN code What is PIN code?Basic Operation Turning On the ProjectorTurning Off the Projector Remote Control How to Operate the On-Screen MenuOn-Screen Menu Menu Bar Operating with Projector Control Zoom AdjustmentFocus Adjustment Lens Shift AdjustmentDirect Operation Sound AdjustmentMenu Operation Operating with Remote Control Shutter button Timer buttonPIP button PIP VOL.. buttonPointer Function Laser Pointer FunctionSpotlight Presentation Pointer button Wireless Mouse OperationInput Remote Control OperationRemote Control button operation Input SelectionVideo Component Input Source SelectionInput Menu RGB PC analog RGB ScartAV System Menu Video or S-video Video System SelectionVideo or S-video ComponentPC System Menu Computer AdjustmentComputer System Selection Selecting Computer System ManuallyAuto PC Adj Auto PC AdjustmentPC Adjust Menu To store adjustment parametersManual PC Adjustment To store the adjusted data To clear the adjusted dataImage Level Selection Image Level SelectionImage Menu Image Adjustment Image AdjustmentImage Adjust Menu Progressive SharpnessGamma Noise reductionTo reset the adjusted data, select Reset and press Keystone Screen AdjustmentScreen Adjustment Screen MenuFull Screen Size Adjustment Computer SignalsNormal TrueDigital zoom + For zooming in and out the imagesDigital zoom Zoom Screen Size Adjustment Video, Component SignalsWide Logo SettingSetting Setting Menu LanguageLogo PIN code lock CaptureLogo PIN code lock CaptureEnter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code Background Picture in PictureLamp mode When selecting Lamp1/2 modeTimer setting Lamp life control Lamp controlPointer Display Standby modePower management DisplayOn start Slant settingSlant Shutter Key lock Security Key lock and PIN code lock settingsEnter a PIN code Change the PIN code lock settingChange the PIN code lock setting PIN code lockChange the PIN code Change the PIN codeTest pattern Factory default Factory default Filter Instructions Maintenance and CareReplacing the Filter Cartridge Scroll counter Filter counterLamp Status Display Lamp 1/2 Replace IndicatorsLamp Mode Changeover Auto Lamp Selection SystemLamp Replacement POA-LMP125 Service Parts No 342 Replacement Lamp Type NoModel No.. of your projector Then check the matters below Cleaning the Projector Cabinet Cleaning the Projection LensAppendix TroubleshootingProblem No powerPower management function does Auto PC adjustment functionDuring the operation Setting does not remain after Turning off powerIndicator blinks or lights Remote Control doesWired remote control does not Wireless Mouse function doesImage System Menu TreeInput SystemScreen PC Adjust InformationSound Setting Projector is operating normally Indicators and Projector ConditionImmediately Projector is detecting abnormal conditionIf the Filter counter reached a time set in the timer ON-SCREEN Resolution Compatible Computer Specifications59.940 List of Picture in Picture Monitor Output at the PIP modeTechnical Specifications Optional Parts PJ Link Notice Terminal D-sub 9 pin Configurations of TerminalsUSB Connector Series B OutputLogo PIN Code Lock No PIN Code Number MemoDimensions KV5AM
Top Page Image Contents