Sanyo PLC-XU305A, PLC-XU355A owner manual Lamp life control Remote control

Page 55

Setting

Lamp control

Lamp control

This function allows you to change brightness of the screen.

Normal

Normal brightness

Eco

Lower brightness reduces the lamp

 

power consumption and extends the

 

lamp life.

Lamp life control

Select the lamp operation when the total lighting time of a lamp exceeds the recommended total hours of use.

Mode 1

The lamp can be turned on even after

 

exceeding the recommended total

Mode 2

hours of use.

The lamp can be turned on even after

 

exceeding the recommended total

 

hours of use. But the projector turns off

Note:

automatically after 3 minutes.

 

Lamp mode cannot be changed for a while after turning on the projector. Lamp needs some time to stabilize after the power is turned on. Stored lamp mode will be active after the lamp is stabilized.

If Mode 2 has been selected and the projection lamp exceeds the recommended total hours of use, the replacement icon will be displayed at the time of power- on. Then the projector will turn off after 3 minutes.

Lamp replacement icon

The Lamp replacement icon will not appear when the Display function is set to Off (p.48), during "Freeze" (p.27), or "No show" (p.28).

Remote control

The eight different remote control codes (Code 1–Code 8) are assigned to the projector; the factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8).

The same code should set on both the projector and the remote control. For example, operating the projector in Code 7, the remote control code also must be switched to Code 7.

To change the code for the projector

Select a remote control code in this Setting Menu.

To change the code for the remote control:

While holding down the MENU button, press the IMAGE button the number of times corresponding to the remote control code for the projector. See “Remote Control Code” on page 13.

Note:

Lamp life control

Remote control

When different codes are set on the projector and on the remote control, any operation cannot be made. In that case, switch the code on the remote control to fit the code on the projector.

If the batteries are removed from the remote control for a long period of time, the remote control code will be reset.

55

Image 55
Contents Memory Viewer Network SupportedFeatures and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Installing the Projector in Proper Position Safety Instructions Air CirculationMoving the Projector AC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Bottom Part Names and FunctionsFront Back⑫ USB Connector Series B ⑤ LAN Connection Terminal ⑥ USB Connector Series aPart Names and Functions ⑧ Warning indicator ② Point Volume +/- buttons⑤ Power indicator ⑦ Auto SETUP/CANCEL button③ Signal Emission indicator Remote ControlPointer Part Names and Functions Laser Pointer FunctionPointer Function SpotlightRemote Control Code Part Names and Functions Wireless Mouse OperationAdjustable Feet Remote Control Operating RangePositioning the Projector InstallationCables used for connection Installation Connecting to a ComputerInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment Note Installation Connecting the AC Power CordSelected Input Source and Lamp Control Input signal guidance windowBasic Operation Turning On the ProjectorPIN Code Input Dialog Box InstallationBasic Operation Turning Off the Projector Top Control How to Operate the On-Screen MenuRemote Control Basic OperationRGB Basic Operation Menu BarAuto Setup Function Zoom and Focus AdjustmentKeystone Correction Mute Basic Operation Sound AdjustmentVolume Volume Dialog BoxBasic Operation Remote Control Operation Screen button Timer buttonNo SHOw button Image buttonInput Source Selection RGB Computer 1/Computer Analog Computer InputInput Menu Input Menu PC System Menu Computer Input Computer System SelectionAuto PC adj Computer Input Auto PC AdjustmentPC adjust Menu To store adjustment parametersComputer Input Manual PC Adjustment Store ResetMode free Computer InputImage select Menu Image Mode SelectionImage Adjust Menu Computer Input Image AdjustmentScreen Menu Screen Size AdjustmentFor zooming in and out the images Digital zoom + CustomScale H/V Position H/VInput Source Selection Video, S-video Video InputVideo Component RGB Scart Component AV System Menu Component Video Input Video System SelectionAV System Menu Video or S-Video Video or S-VideoCinema Video Input Image Mode SelectionBlackboard or Colorboard Video Input Image AdjustmentColor TintStore Store Menu Off Disabled Lower reduction Higher reduction ProgressiveVideo Input Noise reductionVideo Input Screen Size Adjustment Language SettingSetting Setting Menu LanguageAuto Keystone Auto setupAuto setup Input searchUser Power off? p.22Keystone BackgroundLogo select , capture and Logo PIN code change Logo Logo and Logo PIN code lock settings Logo selectCapture Capture Logo PIN code lockLogo PIN code lock Enter a Logo PIN code Change the Logo PIN code lock settingLogo PIN code change Rear CeilingLarge , Middle or Small , Arrow , Finger or Dot and press Power management On start Standby modeClosed caption Lamp life control Remote control PIN code lock Key lockSecurity Key lock and PIN code lock Key lockPIN code change Change the PIN code lock settingEnter a PIN code Change the PIN code Enter a PIN codeFilter counter Filter counterFan Fan controlFilter counter to the factory default settings Factory defaultLogo , PIN code lock , Logo PIN code lock , Lamp counter Input Source Information Display InformationNote Then check the matters below Maintenance and CleaningIndicator lights red Projector is shut down and the WarningResetting the Filter Counter Maintenance and Cleaning Cleaning the FiltersCleaning the Projection Lens Maintenance and Cleaning Attaching the Lens CapCleaning the Projector Cabinet Maintenance and Cleaning Lamp Replacement Service Parts No 343 Maintenance and CleaningAppendix TroubleshootingAppendix Image is distorted or runs off Remote Control does not workIndicator blinks or lights Wireless Mouse function does not workAppendix Computer Input Appendix Menu TreeVideo Input Indicators Appendix Indicators and Projector ConditionON-SCREEN Resolution Appendix Compatible Computer SpecificationsSpecifications are subject to change without notice Mechanical Information Panel ResolutionSignal Compatibility PowerOptional Parts Appendix PJ Link Notice USB Connector Series B Appendix Configurations of TerminalsUSB Thumb Drive Case Appendix PIN Code Number MemoPIN Code Lock No Logo PIN Code Lock NoUnit mminch Appendix DimensionsKG5AE