Sanyo PLC-XU305A, PLC-XU355A Compliance, AC Power Cord for the United States and Canada

Page 7

Compliance

Federal Communications Commission Notice

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Number

: PLC-XU305A, PLC-XU355A

Trade Name

: Sanyo

Responsible party

: SANYO NORTH AMERICA CORPORATION

Address

: 21605 Plummer Street, Chatsworth, California 91311

Telephone No.

: (818)998-7322

AC Power Cord Requirement

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada:

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician.

GROUND

AC Power Cord for the United Kingdom:

This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus ASA . If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions. If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.

The end of the flexible cord should be suitably prepared and the correct plug fitted.

WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET OUTLET.

The Wires in this mains lead are coloured in accordance with the following code: Green-and-yellow..Earth

Blue . . . . . Neutral Brown . . . . . Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

WARNING: THIS APPARATUS MUST BE EARTHED.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.



Image 7
Contents Memory Viewer Network SupportedFeatures and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Installing the Projector in Proper Position Safety Instructions Air CirculationMoving the Projector AC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Bottom Part Names and FunctionsFront Back⑫ USB Connector Series B ⑤ LAN Connection Terminal ⑥ USB Connector Series aPart Names and Functions ⑧ Warning indicator ② Point Volume +/- buttons⑤ Power indicator ⑦ Auto SETUP/CANCEL button③ Signal Emission indicator Remote ControlPointer Part Names and Functions Laser Pointer FunctionPointer Function SpotlightRemote Control Code Part Names and Functions Wireless Mouse OperationAdjustable Feet Remote Control Operating RangePositioning the Projector InstallationCables used for connection Installation Connecting to a ComputerInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment Note Installation Connecting the AC Power CordSelected Input Source and Lamp Control Input signal guidance windowBasic Operation Turning On the ProjectorPIN Code Input Dialog Box InstallationBasic Operation Turning Off the Projector Top Control How to Operate the On-Screen MenuRemote Control Basic OperationRGB Basic Operation Menu BarAuto Setup Function Zoom and Focus AdjustmentKeystone Correction Mute Basic Operation Sound AdjustmentVolume Volume Dialog BoxBasic Operation Remote Control Operation Screen button Timer buttonNo SHOw button Image buttonInput Source Selection RGB Computer 1/Computer Analog Computer InputInput Menu Input Menu PC System Menu Computer Input Computer System SelectionAuto PC adj Computer Input Auto PC AdjustmentPC adjust Menu To store adjustment parametersComputer Input Manual PC Adjustment Store ResetMode free Computer InputImage select Menu Image Mode SelectionImage Adjust Menu Computer Input Image AdjustmentScreen Menu Screen Size AdjustmentFor zooming in and out the images Digital zoom + CustomScale H/V Position H/VInput Source Selection Video, S-video Video InputVideo Component RGB Scart Component AV System Menu Component Video Input Video System SelectionAV System Menu Video or S-Video Video or S-VideoCinema Video Input Image Mode SelectionBlackboard or Colorboard Video Input Image AdjustmentColor TintStore Store Menu Off Disabled Lower reduction Higher reduction ProgressiveVideo Input Noise reductionVideo Input Screen Size Adjustment Language SettingSetting Setting Menu LanguageAuto Keystone Auto setupAuto setup Input searchUser Power off? p.22Keystone BackgroundLogo select , capture and Logo PIN code change Logo Logo and Logo PIN code lock settings Logo selectCapture Capture Logo PIN code lockLogo PIN code lock Enter a Logo PIN code Change the Logo PIN code lock settingLogo PIN code change Rear CeilingLarge , Middle or Small , Arrow , Finger or Dot and press Power management On start Standby modeClosed caption Lamp life control Remote control PIN code lock Key lockSecurity Key lock and PIN code lock Key lockPIN code change Change the PIN code lock settingEnter a PIN code Change the PIN code Enter a PIN codeFilter counter Filter counterFan Fan controlFilter counter to the factory default settings Factory defaultLogo , PIN code lock , Logo PIN code lock , Lamp counter Input Source Information Display InformationNote Then check the matters below Maintenance and CleaningIndicator lights red Projector is shut down and the WarningResetting the Filter Counter Maintenance and Cleaning Cleaning the FiltersCleaning the Projection Lens Maintenance and Cleaning Attaching the Lens CapCleaning the Projector Cabinet Maintenance and Cleaning Lamp Replacement Service Parts No 343 Maintenance and CleaningAppendix TroubleshootingAppendix Image is distorted or runs off Remote Control does not workIndicator blinks or lights Wireless Mouse function does not workAppendix Computer Input Appendix Menu TreeVideo Input Indicators Appendix Indicators and Projector ConditionON-SCREEN Resolution Appendix Compatible Computer SpecificationsSpecifications are subject to change without notice Mechanical Information Panel ResolutionSignal Compatibility PowerOptional Parts Appendix PJ Link Notice USB Connector Series B Appendix Configurations of TerminalsUSB Thumb Drive Case Appendix PIN Code Number MemoPIN Code Lock No Logo PIN Code Lock NoUnit mminch Appendix DimensionsKG5AE