Sanyo PLC-XTC50AL owner manual Appendix, Troubleshooting, Problem, No power, Image is out of focus

Page 69

Appendix

Troubleshooting

Before calling your dealer or service center for assistance, check the items below once again.

–Make sure you have properly connected the projector to peripheral equipment as described on pages 20–22.

–Make sure all equipment is connected to AC outlet and the power is turned on.

–When the projector does not project an image from the connected computer, restart the computer.

Problem:

– Solutions

No power

– Plug the power cord of the projector into the AC outlet.

 

– See if the POWER indicator is lit.

 

– Wait until the POWER indicator stops blinking to turn on the projector

 

again. See on page 25.

 

– Check the WARNING TEMP. indicator. If the WARNING TEMP.

 

indicator is blinking, the projector cannot be turned on. See page 67.

 

– Check the projection lamp. See page 65.

 

– Check if the projector is installed in proper position.

 

– Unlock the Key lock function for the projector. See page 57.

PIN code dialog box appears at start-up..

The initial display is not shown..

The initial display is not same with the default one..

An icon other than Input mode, Lamp control or lamp status icon appears..

No image

–PIN code lock is being set. Enter a PIN code; the "1234" or numbers you have set. See pages 24, 58.

–Make sure "Off" or "Countdown Off" are not chosen at Display function. See page 55.

–Make sure "User" or "Off" are not chosen at Logo function. See page 49.

–That is the Lamp replacement icon or the Filter warning icon. See pages 60,65.

–Check the connection between your computer or video equipment and the projector. See pages 20–22.

–See if the input signal is correctly output from your computer. Some laptop computers may need to change the setting for monitor output when connecting to the projector See your computer’s instruction manual for the setting.

–It takes about 20 seconds to display an image after turning on the projector.

–See if the selected system is corresponding with your computer or video equipment. See pages 36, 37.

–Select correct input source once again through menu operation. See page 35.

–Make sure the temperature is not out of the specified Operating Temperature (41 ˚F–104 ˚F [5 ˚C–40 ˚C]).

Image is out of focus..

–Adjust focus of the projector. See pages 28, 30.

–Provide proper distance between the projector and projection screen.

–Check the projection lens to see if it needs cleaning. See page 68.

–Moving the projector from a cool to warm place may result in moisture condensation on the projection lens. In such cases, leave the projector off and wait until condensation evaporates.

69

Page 68 Page 70
Image 69
Page 68 Page 70
Contents Model PLC-XTC50AL Features and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Top Control Air CirculationPositioning Precautions Installing the Projector in Proper DirectionsTransporting the Projector Moving the ProjectorAC Power Cord for the United States and Canada AC Power Cord for the United KingdomCompliance Part Names and Functions FrontBack Audio 2 Jack Side TerminalAudio 3 Jacks LMONO/R BNC Input Jacks1R/C Jack 0USB Connector Series BTop Control Remote Control 9RESET/ON/ALL-OFF switch 4P-TIMER button5D..ZOOM button 6ZOOM ed buttonsWired Remote Control Remote Control Battery InstallationRemote Control Code Adjustable Feet InstallationLens Installation Removing the lensAttaching the lens to the projector Connecting to a Computer Digital and Analog RGB VGA Cables used for connectionMonitor OUT and Audio OUT Specifications Connecting for Audio SignalProjector side AC outlet side Connecting the AC Power CordBasic Operation What is PIN code?Turning On the Projector Enter a PIN codeTurning Off the Projector How to Operate the On-Screen Menu Remote ControlOn-Screen Menu Menu Bar Focus Adjustment Zoom AdjustmentLens Shift Adjustment Operating with Projector ControlSound Adjustment Direct OperationMenu Operation Operating with Remote Control Timer button Shutter buttonKeystone button Laser Pointer Function Pointer FunctionSpotlight Presentation Pointer button Wireless Mouse OperationRemote Control button operation Remote Control OperationInput Selection InputInput Menu Input Source SelectionRGB PC analog RGB Scart RGB PC digital Video ComponentVideo or S-video Video System SelectionComponent AV System Menu Video or S-videoComputer System Selection Computer AdjustmentSelecting Computer System Manually PC System MenuPC Adjust Menu Auto PC AdjustmentTo store adjustment parameters Auto PC AdjManual PC Adjustment To store the adjusted data To clear the adjusted dataImage Level Selection Image Level SelectionImage Menu Image Adjustment Image AdjustmentImage Adjust Menu Gamma SharpnessNoise reduction ProgressiveTo reset the adjusted data, select Reset and press Screen Adjustment Screen AdjustmentScreen Menu KeystoneScreen Size Adjustment Computer Signals For zooming in and out the images Digital zoom +Digital zoom Screen Size Adjustment Video, Component Signals Setting SettingSetting Menu Language LogoLogo PIN code lock CaptureChange the Logo PIN code lock setting Enter a Logo PIN codeChange the Logo PIN code When selecting Lamp1/2 mode Lamp modeTimer setting Lamp life control Lamp controlPointer Power management Standby modeDisplay DisplaySlant setting On startSlant Security Key lock and PIN code lock settings Key lockKey lock Change the PIN code lock setting Change the PIN code lock settingPIN code lock Enter a PIN codeChange the PIN code Change the PIN codeTest pattern Factory default Factory defaultFilter Instructions Maintenance and CareReplacing the Filter Cartridge Scroll counter Filter counterLamp Mode Changeover Lamp 1/2 Replace IndicatorsAuto Lamp Selection System Lamp Status DisplayLamp Replacement Replacement Lamp Type No POA-LMP125 Service Parts No 342Model No.. of your projector Then check the matters below Cleaning the Projector Cabinet Cleaning the Projection LensProblem TroubleshootingNo power AppendixDuring the operation Setting does not remain after Auto PC adjustment functionTurning off power Power management function doesWired remote control does not Remote Control doesWireless Mouse function does Indicator blinks or lightsInput Menu TreeSystem InformationPC Adjust Screen SettingProjector is operating normally Indicators and Projector ConditionImmediately Projector is detecting abnormal conditionIf the Filter counter reached a time set in the timer ON-SCREEN Resolution Compatible Computer Specifications59.940 Technical Specifications Optional Parts PJ Link Notice Configurations of Terminals OutputTerminal D-sub 9 pin Logo PIN Code Lock No PIN Code Number MemoDimensions KH7AM

PLC-XTC50AL specifications

The Sanyo PLC-XTC50AL is a leading-edge projector that has made a significant impact in the world of multimedia presentations and visual displays. Renowned for its robust performance, this projector is designed for a variety of settings, including business presentations, educational environments, and even larger auditoriums.

One of the defining features of the Sanyo PLC-XTC50AL is its high brightness level. With a brightness rating of 5000 ANSI lumens, it can deliver vibrant images even in well-lit environments, making it ideal for conference rooms where ambient light can be a challenge. This high brightness is complemented by a WXGA resolution of 1280 x 800 pixels, ensuring that images and text are sharp, clear, and easily readable from a distance.

Another significant advantage of the PLC-XTC50AL is its advanced color technology. The projector employs Sanyo’s proprietary Smooth Image technology to enhance color accuracy and richness. This feature, combined with the projector’s 3LCD system, ensures that colors are well-balanced and lifelike, providing audiences with a captivating viewing experience.

In terms of connectivity, the Sanyo PLC-XTC50AL doesn't disappoint. It offers multiple input options, including HDMI, VGA, and component video, making it versatile for connecting a variety of devices such as laptops, DVD players, and even gaming consoles. This flexibility is crucial for users who often switch between different media sources during their presentations.

The projector is also engineered for user convenience and maintenance. It features an easy-access lamp compartment that allows for quick bulb replacements, which helps minimize downtime during crucial presentations. Additionally, the projector has a long lamp life, reaching up to 4000 hours in standard mode, significantly reducing operational costs over time.

Moreover, the PLC-XTC50AL is designed with portability in mind, featuring a compact enclosure and lightweight design that makes it easy to transport between locations. It also incorporates features like digital keystone correction, which helps adjust the image up to a certain angle, preventing distortion and ensuring a perfectly squared image regardless of the projector’s position.

For organizations and individuals looking for a reliable, high-performance projector, the Sanyo PLC-XTC50AL stands out as a compelling choice, blending impressive specifications with user-friendly features tailored to meet the demands of dynamic presentation environments.
Top Page Image Contents