Sanyo PLC-XTC50AL owner manual When selecting Lamp1/2 mode, Lamp mode, Timer setting

Page 52

Setting

Lamp mode

This Projector is equipped with 2 Projection Lamps. This function allows you to choose how to use the lamp as follows.

Lamp1............ Always use Lamp 1.

Lamp2 ........... Always use Lamp 2.

Lamp1/2......... Automatically switch the active lamp from one

lamp to the other .

The following items can be selected. Timer setting :

. . . . . . Switch the timer to On/Off.

Start . . . . . Time to start timer. (0-24 hours)

Lamp interval . Time to lamp change. (1-24 hours)

✔Note:

•When Lamp 1 or Lamp 2 mode is switched to Lamp 1/2 mode, the active lamp changes after the total lighting time of a currently used lamp exceeds 10 hours.

•When the total lighting time of one lamp exceeds the recommended total hours of use in the Lamp 1/2 mode, the Lamp mode will be switched to Lamp 1 or Lamp 2 mode automatically. Switching operation is done when the lamp is changed.

•Lamp mode cannot be changed for a while after turning on the projector. Lamp needs some time to stabilize after the power is turned on. Stored lamp mode will be active after the lamp is stabilized.

•When the different lighting time of the lamps light alternately, you may recognize different brightness and white balance on each different lighting time of lamps.

When you change the other lamp, we recommend you always use the other lamp which is not changed.

•When theTimer is set to “Off” and the total lighting time of one lamp exceeds 10 hours of use in the Lamp 1/2 mode, one lamp will be switched to the other lamp automatically. Switching operation is done when the projector is turned Off and On.

•When the projector is switched to Off/On (including Standby),Timer setting is reset to off.

•When theTimer is set to “On” in the Lamp1/2 mode, the Lamp timer counter is displayed on the right side of the Lamp mode in the Information menu. (p.30)

Set the red frame pointer to the item and press the SELECT button.

Use the Point ed buttons to set the Lamp mode. Select from (Lamp1, Lamp2 or Lamp 1/2).

Select [Yes] to activate it.

When selecting Lamp1/2 mode

Timer setting

Use the Point 7 8 buttons to select items and press the SELECT buttons.

Select [Yes] to activate it.

✔Note:

•The Lamp timer counter appears with the Lamp status before 10 seconds when the Lamp will be switched.

52

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Model PLC-XTC50AL Features and Design Table of Contents Safety Precaution To the OwnerSafety Instructions Air Circulation Top ControlInstalling the Projector in Proper Directions Positioning PrecautionsMoving the Projector Transporting the ProjectorAC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Front Part Names and FunctionsBack Side Terminal Audio 2 JackAudio 3 Jacks LMONO/R BNC Input Jacks0USB Connector Series B 1R/C JackTop Control Remote Control 4P-TIMER button 9RESET/ON/ALL-OFF switch5D..ZOOM button 6ZOOM ed buttonsRemote Control Battery Installation Wired Remote ControlRemote Control Code Installation Adjustable FeetRemoving the lens Lens InstallationAttaching the lens to the projector Connecting to a Computer Digital and Analog RGB Cables used for connection VGAConnecting for Audio Signal Monitor OUT and Audio OUT SpecificationsConnecting the AC Power Cord Projector side AC outlet sideWhat is PIN code? Basic OperationTurning On the Projector Enter a PIN codeTurning Off the Projector Remote Control How to Operate the On-Screen MenuOn-Screen Menu Menu Bar Zoom Adjustment Focus AdjustmentLens Shift Adjustment Operating with Projector ControlDirect Operation Sound AdjustmentMenu Operation Operating with Remote Control Shutter button Timer buttonKeystone button Pointer Function Laser Pointer FunctionSpotlight Wireless Mouse Operation Presentation Pointer buttonRemote Control Operation Remote Control button operationInput Selection InputInput Source Selection Input MenuRGB PC analog RGB Scart RGB PC digital Video ComponentVideo System Selection Video or S-videoComponent AV System Menu Video or S-videoComputer Adjustment Computer System SelectionSelecting Computer System Manually PC System MenuAuto PC Adjustment PC Adjust MenuTo store adjustment parameters Auto PC AdjManual PC Adjustment To clear the adjusted data To store the adjusted dataImage Level Selection Image Level SelectionImage Menu Image Adjustment Image AdjustmentImage Adjust Menu Sharpness GammaNoise reduction ProgressiveTo reset the adjusted data, select Reset and press Screen Adjustment Screen AdjustmentScreen Menu KeystoneScreen Size Adjustment Computer Signals Digital zoom + For zooming in and out the imagesDigital zoom Screen Size Adjustment Video, Component Signals Setting SettingSetting Menu Language LogoCapture Logo PIN code lockEnter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code Lamp mode When selecting Lamp1/2 modeTimer setting Lamp control Lamp life controlPointer Standby mode Power managementDisplay DisplayOn start Slant settingSlant Key lock Security Key lock and PIN code lock settingsKey lock Change the PIN code lock setting Change the PIN code lock settingPIN code lock Enter a PIN codeChange the PIN code Change the PIN codeTest pattern Factory default Factory defaultMaintenance and Care Filter InstructionsReplacing the Filter Cartridge Filter counter Scroll counterLamp 1/2 Replace Indicators Lamp Mode ChangeoverAuto Lamp Selection System Lamp Status DisplayLamp Replacement POA-LMP125 Service Parts No 342 Replacement Lamp Type NoModel No.. of your projector Then check the matters below Cleaning the Projection Lens Cleaning the Projector CabinetTroubleshooting ProblemNo power AppendixAuto PC adjustment function During the operation Setting does not remain afterTurning off power Power management function doesRemote Control does Wired remote control does notWireless Mouse function does Indicator blinks or lightsMenu Tree InputSystem InformationSetting PC Adjust ScreenIndicators and Projector Condition Projector is operating normallyProjector is detecting abnormal condition ImmediatelyIf the Filter counter reached a time set in the timer Compatible Computer Specifications ON-SCREEN Resolution59.940 Technical Specifications Optional Parts PJ Link Notice Output Configurations of TerminalsTerminal D-sub 9 pin PIN Code Number Memo Logo PIN Code Lock NoDimensions KH7AM

PLC-XTC50AL specifications

The Sanyo PLC-XTC50AL is a leading-edge projector that has made a significant impact in the world of multimedia presentations and visual displays. Renowned for its robust performance, this projector is designed for a variety of settings, including business presentations, educational environments, and even larger auditoriums.

One of the defining features of the Sanyo PLC-XTC50AL is its high brightness level. With a brightness rating of 5000 ANSI lumens, it can deliver vibrant images even in well-lit environments, making it ideal for conference rooms where ambient light can be a challenge. This high brightness is complemented by a WXGA resolution of 1280 x 800 pixels, ensuring that images and text are sharp, clear, and easily readable from a distance.

Another significant advantage of the PLC-XTC50AL is its advanced color technology. The projector employs Sanyo’s proprietary Smooth Image technology to enhance color accuracy and richness. This feature, combined with the projector’s 3LCD system, ensures that colors are well-balanced and lifelike, providing audiences with a captivating viewing experience.

In terms of connectivity, the Sanyo PLC-XTC50AL doesn't disappoint. It offers multiple input options, including HDMI, VGA, and component video, making it versatile for connecting a variety of devices such as laptops, DVD players, and even gaming consoles. This flexibility is crucial for users who often switch between different media sources during their presentations.

The projector is also engineered for user convenience and maintenance. It features an easy-access lamp compartment that allows for quick bulb replacements, which helps minimize downtime during crucial presentations. Additionally, the projector has a long lamp life, reaching up to 4000 hours in standard mode, significantly reducing operational costs over time.

Moreover, the PLC-XTC50AL is designed with portability in mind, featuring a compact enclosure and lightweight design that makes it easy to transport between locations. It also incorporates features like digital keystone correction, which helps adjust the image up to a certain angle, preventing distortion and ensuring a perfectly squared image regardless of the projector’s position.

For organizations and individuals looking for a reliable, high-performance projector, the Sanyo PLC-XTC50AL stands out as a compelling choice, blending impressive specifications with user-friendly features tailored to meet the demands of dynamic presentation environments.
Top Page Image Contents