Sanyo PLC-XK2600 owner manual Lamp Handling Precautions

Page 62

Maintenance and Cleaning

ORDER REPLACEMENT LAMP

Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer.

Model No. of your projector : PLC-XK2200; PLC-XK2600

Replacement Lamp Type No.: POA-LMP142

(Service Parts No. 610 349 7518)

LAMP HANDLING PRECAUTIONS

This projector uses a high-pressure lamp which must be handled carefully and properly.

Improper handling may result in accidents, injury, or create a fire hazard.

Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same life for each lamp. Some lamps may fail or terminate their life in a shorter period of time than other similar lamps.

If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.

(Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.

A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service center for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

62

Image 62
Contents Model PLC-XK2200 PLC-XK2600 Network SupportedFeatures and Design Table of Contents Safety Precaution To the OwnerSafety Instructions Air Circulation Safety InstructionsInstalling the Projector in Proper Position Moving the ProjectorAC Power Cord for the United Kingdom AC Power Cord RequirementAC Power Cord for the United States and Canada ComplianceBack Part Names and FunctionsFront Bottom⑤ LAN Connection Terminal Part Names and FunctionsRear Terminal Top Control Remote Control Remote Control Code Remote Control Battery InstallationRemote Control Operating Range Menu buttonPositioning the Projector InstallationAdjustable Foot NoteCables used for connection InstallationConnecting to a Computer Connecting to Video Equipment MICConnecting to Component Video and RGB Scart Equipment Projector side AC outlet side Connecting the AC Power CordTo power cord To the AC outlet Connector on your For the U.KTurning On the Projector Input signal guidance windowBasic Operation Selected Input Source and Lamp ControlEnter a PIN code What is PIN code?Basic Operation PIN Code Input Dialog BoxTurning Off the Projector Cooling fans keep running. You can selectTop Control How to Operate the On-Screen MenuRemote Control On-Screen MenuMenu Bar Auto Setup button Point buttons Zoom and Focus AdjustmentAuto Setup Function Keystone CorrectionSound Adjustment Remote Control Operation No Show button Timer buttonTimer Image buttonInput Source Selection RGB Computer 1/Computer Remote Control Computer 1 buttonComputer Input Computer 2 buttonAuto Computer InputComputer System Selection ModeTo store adjustment parameters Auto PC AdjustmentPC adjust Menu Auto PC adjManual PC Adjustment Store ResetMode free Image Mode Selection Image Adjustment Screen Size Adjustment Keystone Digital zoom +Digital zoom CeilingVideo button Video Video button S-video Video InputInput Source Selection Video, S-video VideoInput Menu Video InputInput Source Selection Component, RGB Scart 21-pin Component buttonComponent Auto Video System SelectionVideo or S-video Auto AV System Menu Video or S-video AV System Menu ComponentDynamic Tint Image Adjust MenuColor Blackboard or ColorboardStore Menu Noise reductionProgressive Screen Menu Note Keystone Setting Menu SettingSetting LanguageSetting Auto setupDisplay Logo Logo and Logo PIN code lock settingsBackground Logo selectCapture Logo PIN code lockEnter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code lock setting Logo PIN code changeShut down TerminalDirect on Count down 00000-18000 Standby modeStop or Cancel the P-timer via Remote Control At Restart to resume Count up orClosed Caption To change the code for the remote control Code To change the code for the projectorPIN code lock Security Key lock and PIN code lockKey lock Key lockChange the PIN code Change the PIN code lock settingEnter a PIN code Enter a PIN code Change the PIN codeFan Video delay controlLamp counter reset Fan controlOff/2000H/3000H/4000H Note Factory defaultFilter counter Input Source Information Display Remote ControlInformation Note Then check the matters below Maintenance and CleaningProjector is shut down and the Warning indicator lights red Filter counter reset Maintenance and CleaningResetting the Filter Counter Replacing the FilterAttaching the Lens Cap Cleaning the Projection LensCleaning the Projector Cabinet Lamp Replacement Reset the lamp counterLamp Handling Precautions Troubleshooting AppendixAppendix Image is distorted or runs off Remote Control doesIndicator blinks or lights PIN code dialog box appearsAppendix Menu Tree Computer Input/Video InputVideo Input Computer InputRed Indicators and Projector ConditionIndicators RedCompatible Computer Specifications DisplayTechnical Specifications Optional Parts PJ Link Notice Attaching the Filter Cover to the ProjectorTX + RX + Configurations of TerminalsTerminal Analog RGB Mini D-sub 15 pin Horiz. sync. Input/OutputPIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Dimensions Unit mminchKS8AE