Sanyo PLC-XE33 owner manual Command Function

Page 47

Use of telnet

3.When communication is established correctly, the word "PASSWORD:" appears on the window. Type the login password (Network PIN code*2) for the projector and then press "Enter" key on the keyboard. If you do not set up the Network PIN code, just press "Enter" key.

When the word "Hello" is replied, login has been succeeded.

*The password "1234" is used for the example.

4.Type the commands, refer to below table, to control the projector and then press "Enter" key for termination. For example, type "C00" which is a command to turn on the projec- tor, and press "Enter" key. Confirm the projector is turning on.

*Enter with ASCII 64-byte capital characters and one-byte characters.

To disconnect the communication, press "Ctrl" key and "]" key at the same time, type "close" and then press "Enter" key on the Keyboard.

> close [return]

The table below shows the typical command lists for controlling this projector and please consult your local dealer for further information of another commands.

Command list table

Command		Function
	C00	Power on
	C02	Power off
	C09	Volume up
	C0A	Volume down
	C0B	Audio Mute on
	C0C	Audio Mute off
	C1C	Menu display on
	C1D	menu display off

*1 Further instructions about the telnet application, please see the on-line guide on your computer. *2 The password is a Network PIN code decided item "Network PIN code setting" (☞pp.14, 23). If the authentication of the entered password is failed 4 times continuously, the communication will be

disconnected automatically. Please try again for the connection.

✐If the password or any command is not entered for more than 30 seconds, the communication will be disconnected automatically. Please try again for the connection.

ENGLISH

47

Image 47

Contents Network Set-up and Operation Wired Setting Projector Set-up and OperationTelephone No 818998-7322 ComplianceFederal Communications Commission Notice AddressSafety instructions Table of contents Chapter Web Management function +p.31 FeaturesRequired operating environment for computers Network specifications of the projectorTrademarks Expression/AbbreviationUse of this manual Install the Software on computers Flow of installationConnect the LAN and set the configuration Network Configuration has completedPreparation Setup Procedures Connecting to the LAN line Description Network PIN code Network factory default Wired LAN factory default settings Chapter Basic Setting and Operation Enter the IP address Login the setting page of the projectorLogin Setting Display of main settingMain setting page in the display Sub menu tab Switches the sub menu tab Main menuExample of the setting How to use the settingSelect items by ticking on check boxes Select an item by selecting a radio buttonPassword for PJLink function +p.23 Initial settingSets the Network PIN code to login the setting page +p.23 Switches PJLink password authentication on or off +p.23Whats PJLink? Network PIN code settingPJLink and password setting To 32 alphanumeric characters can be used for the passwordSets Dhcp or Manual Network configurationDisplays the selected LAN mode Abnormality Mail settingSetting Smtp server and administrator address Sets server name or IP address of the Smtp serverOption Registering and deleting E-mail addressesOption selection for sending alert mail Up to 10 E-mail addresses can be registered Check / DeleteExamples Type and contents of alert mail When lamp corres. value reaches preselect use time When PJ lamp replacement time is reachedSnmp setting Click Set button if you tick or un-tick the check box on a Up to 99,999 hours can be set for the time settingTrap check/delete Chapter Controlling the Projector PJ status Power control and status checkDisplays the status of the projectors power. Refer to next Popup confirmation windowStatus Description About projector conditionInput ControlItem Description SystemSuppresses the sound. ON, OFF SoundImage mode Video Computer Image adjustmentPC adjustment Screen mode Video Computer Normal True Wide Full Custom Setting up the projectorScreen setting Setting Highland mode Projector or Remote control. OFFProjector keys, Remote control Normal modeStatus InformationIndication of the lamp status Items DescriptionChapter Appendix To another network Examples of connectionPeer-To-Peer connection Entrance hall Gateway Router installed in the networkUse the IP address assigned to the projector Use of telnetControl Command Function Proxy setting Web browser settingActive Script/JavaScript enable Internet Explorer Examples OS/BrowsersWindows XP Professional Proxy setting Netscape Navigator JavaScript SettingSafari MAC OS X vHow can I restrict access from the computer Why doesn’t the setting page appear in my web browser?How can I install several projectors? Why am I not receiving E-mail alert messages? Why cant be turned on/off with web browser?What are the rules for IP address assignment? What is the MAC address assigned to the projector?Can I update the firmware of the projector SO-KR5AC