Sanyo PLC-WL2503A Maintenance and Cleaning Lamp Replacement, Top Panel, Reset the lamp counter

Page 63

Maintenance and Cleaning

Lamp Replacement

When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP REPLACE indicator should light is depending on the lamp mode.

WARNING:

TURN OFF THE UV LAMP BEFORE

OPENING THE LAMP COVER

Top Panel

This indicator turns yellow when the projection lamp reaches the end of its life.

Lamp replacement icon

Note:

The Lamp replacement icon (Fig.1) will not appear when the Display function is set to Off (p.46), during Freeze(p.25), or No show (p.26).

CAUTION

When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be broken. If replacing the lamp of a projector which has been installed on the ceiling, you should always assume that the lamp is broken, and you should stand to the side of the lamp cover, not underneath it. Remove the lamp cover gently. Small pieces of glass may fall out when the lamp cover is opened. If pieces of glass get into your eyes or mouth, seek medical advice immediately.

CAUTION

Allow a projector to cool for at least 45 minutes before you open the Lamp Cover. The inside of the projector can become very hot.

CAUTION

For continued safety, replace with a lamp of the same type. Do not drop a lamp or touch a glass bulb! The glass can shatter and may cause injury.

Follow these steps to replace the lamp.

1

Turn off the projector and unplug the AC power cord.

Let the projector cool for at least 45 minutes.

2

Loosen the screw and open the lamp cover.

3

Loosen the three (3) screws that secure the lamp. Lift

the lamp out of the projector by using the handle.

Lamp Cover

Screw

4 Replace the lamp with a new one and secure the three

(3)screws. Make sure that the lamp is set properly. Close the lamp cover and secure the screw.

5

Connect the AC power cord to the projector and turn

on the projector.

6

Reset the lamp counter..

See “Resetting the Lamp Counter” on the next page.

Screws

Lamp

Handle

ORDER REPLACEMENT LAMP

Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer.

●

Model No.. of your projector

: PLC-WL2503A

●

Replacement Lamp Type No.

: POA-LMP141

 

 

(Service Parts No. 610 349 0847)

63

Page 62 Page 64
Image 63
Page 62 Page 64
Contents Network Supported Multimedia ProjectorFeatures and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Safety Instructions Air Circulation Installing the Projector in Proper PositionMoving the Projector AC Power Cord for the United States and Canada AC Power Cord for the United KingdomCompliance Part Names and Functions Front Side Kensington Security Slot ① LAN Connection Terminal Part Names and Functions Side TerminalPart Names and Functions Top Panel Part Names and Functions Remote Control Menu button Image button Remote Control Operating RangeRemote Control Code Two AAA size batteriesInstallation Adjustable FeetPositioning the Projector Cables used for connection Installation Connecting to a ComputerInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment For the U..S..A.. and Canada Installation Connecting the AC Power CordProjector side AC outlet side For Continental Europe For the U..KSelected Input Source and Lamp Control Input signal guidance windowBasic Operation Turning On the ProjectorPIN Code Input Dialog Box Basic OperationDirect OFF Function Basic Operation Turning Off the ProjectorOn-Screen Menu Basic Operation How to Operate the On-Screen MenuRemote Control Top ControlBasic Operation Main Menu Basic Operation Focus Adjustment Auto Setup FunctionKeystone Correction Mute Basic Operation Sound AdjustmentVolume Volume Dialog BoxBasic Operation Remote Control Operation Screen button Timer buttonNo Show button Image buttonComputer Input Input Source Selection Computer 1 RGBInput Menu Video Computer Input Input Source Selection Computer 2 RGBInput Menu Computer 2 button Computer 2 RGBMode Computer Input Computer System SelectionPC System Menu AutoAuto PC adj Computer Input Auto PC adjustmentPC adjust Menu To store adjustment parametersComputer Input Manual PC adjustment Mode free Menu Computer InputStore Menu Computer Input Image Mode Selection Image adjust Menu Computer Input Image AdjustmentScreen Menu Screen Size AdjustmentCustom adj.. Menu Note Custom adjDigital zoom + Digital zoomVideo button Video button S-video Video InputInput Source Selection Video, S-video VideoVideo Input Input Source Selection Component, Scart , Hdmi Or Computer 1Component and then press Video Input Video System SelectionAV System Menu Video or S-video AV System Menu ComponentVideo Input Image Mode Selection Tint Video Input Image AdjustmentImage adjust Menu ColorOff Disabled Lower reduction Higher reduction Progressive Video InputNoise reduction Natural wide Video Input Screen Size AdjustmentZoom WideLanguage SettingSetting Setting Menu Language MenuAuto setup Auto setupInput search Background Power off? p.20Timer KeystoneLogo select Logo Logo and Logo PIN code lock settingsDefault Logo selectCapture Logo PIN code lock CaptureOff Logo PIN code lock Logo PIN code change Change the Logo PIN code lock settingEnter a Logo PIN code Logo PIN code change Enter a Logo PIN codeCeiling Rear Hdmi setupPower management Standby modePower management Count down Min . Only set to Count down , Timer isDirect on NoteClosed caption Off , CC1 , CC2 , CC3 or CC4From Color to White Note Remote control Lamp controlTo change the code for the projector Security Key lock and PIN code lock Enter a PIN code Change the PIN code Lamp counter Video delay controlFan Fan controlFilter counter Factory defaultFactory default Filter counterInput Source Information Display InformationMaintenance and Cleaning Projector is shut down and the Warning indicator lights redNote Then check the matters below Maintenance and Cleaning Replacing the Filter Resetting the Filter CounterFilter counter Reset? Maintenance and Cleaning Attaching the Lens Cover Cleaning the Projection LensCleaning the Projector Cabinet Top Panel Maintenance and Cleaning Lamp ReplacementReset the lamp counter Service Parts No 349Maintenance and Cleaning Resetting the Lamp Counter Press Select button. Lamp replacement counterLamp replacement counter Reset? appears Appendix TroubleshootingColor is strange AppendixNo image No soundPIN code dialog box appears Remote Control doesIndicator blinks or lights Image is distorted or runs offAppendix Menu Tree Information SettingIndicators Appendix Indicators and Projector Condition Note Appendix Compatible Computer SpecificationsFreq Technical Specifications Appendix Optional Parts Terminal Panel ReplacementHdmi 19 PIN Type a Appendix Configurations of TerminalsControl Port Connector D-sub 9 pin Terminal Analog RGB Mini D-sub 15 pinAttatching the Cable Holder Appendix PIN Code Number MemoPIN Code Lock No Logo PIN Code Lock NoPJ Link Notice Appendix DimensionsKJ8AH

PLC-WL2503A specifications

The Sanyo PLC-WL2503A is a cutting-edge projector designed to cater to the diverse needs of both professional and educational environments. With its compact design and advanced features, it stands out as a reliable option for users seeking high-quality visual performance.

One of the main features of the PLC-WL2503A is its impressive brightness output, reaching up to 2500 lumens. This high brightness level ensures that presentations and videos remain clear and vibrant even in well-lit environments. Coupled with a native XGA (1024 x 768) resolution, the projector delivers sharp and detailed images that enhance the professional look of any presentation.

The PLC-WL2503A utilizes advanced DLP (Digital Light Processing) technology, which provides exceptional color accuracy and consistency. This technology is known for its ability to produce vivid colors and deep blacks, making it an excellent choice for video playback and graphic presentations. Additionally, DLP technology allows for a longer lifespan of the projector's light source, resulting in reduced maintenance costs over time.

Another notable characteristic is the projector's versatility in connectivity options. The Sanyo PLC-WL2503A offers various input ports, including HDMI, VGA, and composite video, enabling easy connection to multiple devices such as laptops, DVD players, and gaming consoles. This flexibility ensures that users can seamlessly switch between different source devices without hassle.

In terms of usability, the PLC-WL2503A is designed with user-friendly features, including a straightforward interface and remote control. The integrated lens shift and keystone correction functionalities allow for easy adjustment of the image, enabling users to achieve optimal projection angles and alignment. This feature is especially beneficial in classroom and conference settings where space constraints can often pose challenges.

Furthermore, the projector boasts a lightweight and portable design, making it easy to transport to various locations. This is particularly advantageous for professionals who frequently travel for presentations or educational staff who move between classrooms.

The Sanyo PLC-WL2503A also incorporates eco-friendly technologies, such as an energy-saving mode that reduces power consumption while extending the life of the lamp. This focus on sustainability reflects a growing trend in technology to minimize environmental impact without compromising performance.

In conclusion, the Sanyo PLC-WL2503A combines impressive brightness, advanced DLP technology, versatile connectivity, and user-friendly features, making it an excellent choice for users in need of a reliable and efficient projector. Whether for business presentations or educational purposes, the PLC-WL2503A stands out as a powerful tool that delivers exceptional visual experiences.
Top Page Image Contents