Sanyo PLC-WL2503A owner manual Maintenance and Cleaning Resetting the Lamp Counter

Page 64

Maintenance and Cleaning

Resetting the Lamp Counter

Be sure to reset the Lamp counter after the lamp is replaced. When the Lamp counter is reset, the LAMP REPLACE indicator stops lighting and the Lamp replacement icon disappears.

1

Press the MENU button to display the On-Screen

Menu. Use the Point ▲▼ buttons to select Setting

 

and then press the Point ► or the SELECT button.

2

Use the Point ▲▼ buttons to select Lamp counter

and then press the SELECT button. Use the Point

 

▲▼ buttons to select Lamp counter reset and then

 

press SELECT button. Lamp replacement counter

 

Reset? appears. Select Yes to continue.

3

Another confirmation dialog box appears, select Yes

to reset the Lamp counter.

Note:

Do not reset the Lamp counter without implementing lamp replacement. Be sure to reset the Lamp counter only after replacing the lamp.

Lamp replacement counter Reset?

Lamp replacement counter

Reset?

Lamp replacement counter Reset? appears.

Select Yes, then another confirmation box appears.

Select Yes again to reset the Lamp counter.

LAMP HANDLING PRECAUTIONS

This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard.

●Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same life for each lamp. Some lamps may fail or terminate their life in a shorter period of time than other similar lamps.

●If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.

(Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.

●A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN..

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service center for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

64

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Multimedia Projector Network SupportedFeatures and Design Table of Contents Safety Precaution To the OwnerSafety Instructions Installing the Projector in Proper Position Safety Instructions Air CirculationMoving the Projector AC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Front Side Part Names and Functions Kensington Security Slot Part Names and Functions Side Terminal ① LAN Connection TerminalPart Names and Functions Top Panel Part Names and Functions Remote Control Remote Control Operating Range Remote Control CodeTwo AAA size batteries Menu button Image buttonAdjustable Feet InstallationPositioning the Projector Installation Connecting to a Computer Cables used for connectionInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment Installation Connecting the AC Power Cord Projector side AC outlet sideFor Continental Europe For the U..K For the U..S..A.. and CanadaInput signal guidance window Basic OperationTurning On the Projector Selected Input Source and Lamp ControlBasic Operation PIN Code Input Dialog BoxBasic Operation Turning Off the Projector Direct OFF FunctionBasic Operation How to Operate the On-Screen Menu Remote ControlTop Control On-Screen MenuBasic Operation Main Menu Auto Setup Function Basic Operation Focus AdjustmentKeystone Correction Basic Operation Sound Adjustment VolumeVolume Dialog Box MuteBasic Operation Remote Control Operation Timer button No Show buttonImage button Screen buttonInput Source Selection Computer 1 RGB Computer InputInput Menu Computer Input Input Source Selection Computer 2 RGB Input MenuComputer 2 button Computer 2 RGB VideoComputer Input Computer System Selection PC System MenuAuto ModeComputer Input Auto PC adjustment PC adjust MenuTo store adjustment parameters Auto PC adjComputer Input Manual PC adjustment Computer Input Mode free MenuStore Menu Computer Input Image Mode Selection Computer Input Image Adjustment Image adjust MenuScreen Size Adjustment Screen MenuCustom adj Digital zoom +Digital zoom Custom adj.. Menu NoteVideo Input Input Source Selection Video, S-videoVideo Video button Video button S-videoVideo Input Input Source Selection Component, Scart , Hdmi Video Input Video System Selection AV System Menu Video or S-videoAV System Menu Component Or Computer 1Component and then pressVideo Input Image Mode Selection Video Input Image Adjustment Image adjust MenuColor TintVideo Input Off Disabled Lower reduction Higher reduction ProgressiveNoise reduction Video Input Screen Size Adjustment ZoomWide Natural wideSetting SettingSetting Menu Language Menu LanguageAuto setup Auto setupInput search Power off? p.20 TimerKeystone BackgroundLogo Logo and Logo PIN code lock settings DefaultLogo select Logo selectCapture Capture Logo PIN code lockOff Logo PIN code lock Change the Logo PIN code lock setting Enter a Logo PIN code Logo PIN code changeEnter a Logo PIN code Logo PIN code changeHdmi setup Ceiling RearStandby mode Power managementPower management Min . Only set to Count down , Timer is Direct onNote Count downOff , CC1 , CC2 , CC3 or CC4 Closed captionFrom Color to White Note Lamp control Remote controlTo change the code for the projector Security Key lock and PIN code lock Enter a PIN code Change the PIN code Video delay control FanFan control Lamp counterFactory default Factory defaultFilter counter Filter counterInformation Input Source Information DisplayProjector is shut down and the Warning indicator lights red Maintenance and CleaningNote Then check the matters below Resetting the Filter Counter Maintenance and Cleaning Replacing the FilterFilter counter Reset? Cleaning the Projection Lens Maintenance and Cleaning Attaching the Lens CoverCleaning the Projector Cabinet Maintenance and Cleaning Lamp Replacement Reset the lamp counterService Parts No 349 Top PanelPress Select button. Lamp replacement counter Maintenance and Cleaning Resetting the Lamp CounterLamp replacement counter Reset? appears Troubleshooting AppendixAppendix No imageNo sound Color is strangeRemote Control does Indicator blinks or lightsImage is distorted or runs off PIN code dialog box appearsAppendix Menu Tree Setting InformationAppendix Indicators and Projector Condition IndicatorsAppendix Compatible Computer Specifications  NoteFreq Technical Specifications Terminal Panel Replacement Appendix Optional PartsAppendix Configurations of Terminals Control Port Connector D-sub 9 pinTerminal Analog RGB Mini D-sub 15 pin Hdmi 19 PIN Type aAppendix PIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Attatching the Cable HolderAppendix Dimensions PJ Link NoticeKJ8AH

PLC-WL2503A specifications

The Sanyo PLC-WL2503A is a cutting-edge projector designed to cater to the diverse needs of both professional and educational environments. With its compact design and advanced features, it stands out as a reliable option for users seeking high-quality visual performance.

One of the main features of the PLC-WL2503A is its impressive brightness output, reaching up to 2500 lumens. This high brightness level ensures that presentations and videos remain clear and vibrant even in well-lit environments. Coupled with a native XGA (1024 x 768) resolution, the projector delivers sharp and detailed images that enhance the professional look of any presentation.

The PLC-WL2503A utilizes advanced DLP (Digital Light Processing) technology, which provides exceptional color accuracy and consistency. This technology is known for its ability to produce vivid colors and deep blacks, making it an excellent choice for video playback and graphic presentations. Additionally, DLP technology allows for a longer lifespan of the projector's light source, resulting in reduced maintenance costs over time.

Another notable characteristic is the projector's versatility in connectivity options. The Sanyo PLC-WL2503A offers various input ports, including HDMI, VGA, and composite video, enabling easy connection to multiple devices such as laptops, DVD players, and gaming consoles. This flexibility ensures that users can seamlessly switch between different source devices without hassle.

In terms of usability, the PLC-WL2503A is designed with user-friendly features, including a straightforward interface and remote control. The integrated lens shift and keystone correction functionalities allow for easy adjustment of the image, enabling users to achieve optimal projection angles and alignment. This feature is especially beneficial in classroom and conference settings where space constraints can often pose challenges.

Furthermore, the projector boasts a lightweight and portable design, making it easy to transport to various locations. This is particularly advantageous for professionals who frequently travel for presentations or educational staff who move between classrooms.

The Sanyo PLC-WL2503A also incorporates eco-friendly technologies, such as an energy-saving mode that reduces power consumption while extending the life of the lamp. This focus on sustainability reflects a growing trend in technology to minimize environmental impact without compromising performance.

In conclusion, the Sanyo PLC-WL2503A combines impressive brightness, advanced DLP technology, versatile connectivity, and user-friendly features, making it an excellent choice for users in need of a reliable and efficient projector. Whether for business presentations or educational purposes, the PLC-WL2503A stands out as a powerful tool that delivers exceptional visual experiences.
Top Page Image Contents