Sanyo PLC-WXE45 Maintenance and Cleaning Lamp Replacement, Reset the lamp replacement counter

Page 57
Connect the AC power cord to the projector and turn on the projector.
Turn off the projector and unplug the AC power cord. Let the projector cool for at least 45 minutes.
Turn the projector over. Remove the screw that secures the lamp cover, and then open the lamp cover.
Remove the two screws that secure the lamp. Lift the lamp out of the projector by using the built in handle.

Maintenance and Cleaning

Lamp Replacement

When the projection lamp of the projector reaches the end of its life, the LAMP REPLACE indicator emits a yellow light. If this indicator lights yellow, replace the lamp with a new one promptly.

WARNING:

TURN OFF THE UV LAMP BEFORE

OPENING THE LAMP COVER

Top Panel

This indicator

 

 

turns yellow

 

 

when the

 

 

 

 

projection lamp

 

 

reaches the end

 

 

of its life.

Lamp replacement icon

 

Note:

The Lamp replacement icon will not appear when the Display function is set to “Off” (p.41), during “Freeze” (p.23), or “No show” (p.24).

CAUTION

Allow the projector to cool for at least 45 minutes before you open the Lamp cover. The inside of the projector can become very hot.

CAUTION

For continued safety, replace with a lamp of the same type. Do not drop a lamp or touch a glass bulb! The glass can shatter and may cause injury.

Follow these steps to replace the lamp.

1

2

3

4 Replace the lamp with a new one and secure it with the two screws. Make sure that the lamp is set properly. Put the lamp cover back and secure it with the screw.

5

6 Reset the lamp replacement counter.

See “Lamp Replacement Counter” on the next page.

Lamp Cover

Screw

Lamp Screw

Screw

Handle

ORDER REPLACEMENT LAMP

Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer.

Model No. of your projector : PLC-WXE45

Replacement Lamp Type No. : POA-LMP10

(Service Parts No. 610 332 3855)

57

Image 57
Contents Network Supported Model PLC-WXE45Features and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Safety Instructions Air Circulation Installing the Projector in Proper PositionMoving the Projector AC Power Cord for the United States and Canada AC Power Cord RequirementAC Power Cord for the United Kingdom Compliance⑤ Exhaust Vents Part Names and Functions③ LAN Connection Terminal Part Names and Functions Rear TerminalPart Names and Functions Top Panel Part Names and Functions Remote Control Operating Range Part Names and Functions Remote Control Battery InstallationInstallation Adjustable FeetPositioning the Projector Cables used for connection Installation Connecting to a ComputerAudio Video Installation Connecting to Video EquipmentInstallation Connecting to Component Video Equipment Projector side AC outlet side Installation Connecting the AC Power CordBasic Operation What is PIN code?Turning On the Projector Enter a PIN codeBasic Operation Turning Off the Projector Basic Operation How to Operate the On-Screen Menu Remote Control Menu button Point buttons Select buttonOn-Screen Menu Basic Operation Menu Bar For computer sourceFor video source Basic Operation Focus Adjustment Remote ControlKeystone Correction Remote Control Operation Basic Operation Sound AdjustmentCOMPUTER/VIDEO button Freeze buttonBasic Operation Input Source Selection Computer InputInput Menu Source Select MenuAuto Computer Input Computer System SelectionPC System Menu ModeDirect Operation Remote Control Computer Input Auto PC AdjustmentTo store the adjusted parameters PC Adjust MenuComputer Input Manual PC Adjustment Computer Input Computer Input Image Level Selection Computer Input Image Level Adjustment Normal Screen Size AdjustmentTrue FullCustom For zooming in and out the images Digital zoom +Digital zoom Video Input Menu Operation Remote ControlInput Source Selection Video, S-video Source Select Menu VideoPointer to Computer 1 and then press the Select Video or S-video Auto Video Input Video System SelectionComponent Auto AV System Menu Video or S-videoCinema Video Input Image Level SelectionVideo Input Image Level Adjustment ColorTint Video Input Noise reductionProgressive Zoom Video Input Screen Size AdjustmentWide Natural wideSetting SettingLogo select Logo Logo and Logo PIN code lock settingsCapture Logo select CaptureEnter a Logo PIN code Change the Logo PIN codeLogo PIN code lock Rear CeilingScreen aspect TerminalPower management Standby modeOn start Remote control To change the code for the remote controlOn start Lamp controlSecurity Alarm and PIN code lock settings Change the PIN code lock settingChange the PIN code lock setting PIN code lockChange the PIN code Change the PIN codeFan Filter counterFan control Lamp counterSettin Install a battery Antitheft Alarm FunctionSet and release the Antitheft alarm function Set the alarmSettings Antitheft Alarm FunctionReset the settings Change the PIN codeHow to install the battery Indicator is blinking red Maintenance and CleaningIndicator lights red Projector is shut down and the WarningResetting the Filter Counter Maintenance and Cleaning Cleaning the Air FiltersMaintenance and Cleaning Attaching the Lens Cover Cleaning the Projection LensCleaning the Projector Cabinet Reset the lamp replacement counter Maintenance and Cleaning Lamp ReplacementMaintenance and Cleaning Lamp Replacement Counter Lamp Handling PrecautionsAppendix TroubleshootingAppendix Indicator blinks or lights Sound Appendix Menu TreeComputer Input/Video Input Computer InputSystem AutoSetting Video Input SettingProjector Condition Appendix Indicators and Projector ConditionDisplay Appendix Compatible Computer SpecificationsAppendix Technical Specifications Dimensions AccessoriesOptional Parts Appendix PJ Link Notice Appendix Configurations of Terminals Service Port Connector Terminal Mini DIN 8-PINTerminal Analog RGB Mini D-sub 15 pin Appendix PIN Code Number Memo Alarm PIN Code NoPIN Code Lock No Logo PIN Code Lock NoKM5AC