Kyocera copier manual Auto Clear function, Auto Drawer Switching function

Page 21

Section 2 NAMES OF PARTS

(14)Sort key & indicator

(Press this key when you want to copy with the Sort mode. Make sure that the Sort indicator is lit green. See page 5-9.)

(15)Program key & indicator

(Press this key when you want to copy with the Program function. Make sure that the Program indicator is lit green. See page 5-10.)

(16)Add Toner indicator

(This indicator lights red when the toner supply has run low. See page 9-2.)

(17)Memory Overflow indicator

(This indicator lights red if the memory becomes full during scanning of originals. See page 8-1.)

(18)Upper drawer indicator

(This indicator lights green when the upper drawer is selected as the source of paper feed and it flashes green when the drawer has run out of paper.)

(19)Upper drawer misfeed indicator

(This indicator lights red if a paper jam occurs in the upper drawer.)

(20)Paper Feeder indicator

(This indicator lights green when the optional Paper Feeder is selected as the source of paper feed and it flashes green when the drawer has run out of paper.)

(21)Paper Feeder misfeed indicator

(This indicator lights red if a paper jam occurs in the optional Paper Feeder.)

(22)Multi-bypass tray indicator

(This indicator lights green when the multi-bypass tray is selected as the source of paper feed and it flashes green when the tray has run out of paper.)

(23)Multi-bypass tray misfeed indicator

(This indicator lights red if a paper jam occurs in the multi-bypass tray.)

(24)Document Processor indicator

(This indicator will light red if an original jam occurs.)

Initial mode (the state that the copier enters at the end of warm-up or when the Reset/Power key is pressed)

The upper drawer is selected as the source for paper feed, the number of copies to be made is set to “1” and “Text & Photo” is selected as the image quality mode.

*If the optional Paper Feeder is installed on your copier, it is possible for you to change which drawer will be automatically selected in the initial mode. (See “Default Drawer” on page 6-2.)

*It is also possible for you to change which image quality mode will be automatically selected in the initial mode. (See “Image Quality Mode” on page 6-1.)

Auto Clear function

A pre-set number of seconds (between 10 and 270) after copying stops, the Auto Clear function will automatically engage and the copier will return to the same settings as those after warm up (initial mode settings).(However, the copy exposure setting will not change.) Copies can continually be made using the same settings (copy mode and number of copies) if the next batch of copying is started before the Auto Clear function engages.

*See “Auto Clear Time” on page 6-4for information on changing the amount of time before the Auto Clear function automatically engages, and “Auto Clear ON/OFF” on page 6-3for information on turning the Auto Clear function ON and OFF.

Auto Drawer Switching function

If two drawers contain the same size of paper and the paper in one drawer runs out during copying, the Auto Drawer Switching function will switch paper feed from the empty drawer to the other drawer that still contains paper so that copying can continue non-stop.

*The optional Paper Feeder is required in order to use the Auto Drawer Switching function.

*It is possible for you to turn the Auto Drawer Switching function OFF. (See “Auto Drawer Switching ON/OFF” on page 6-2.)

2-5

Image 21
Contents 1500 Page Troubleshooting Copy Default SettingsMaintenance and Operation Information IMPORTANT! Please Read FirstContents Eco-Copy mode See Preset Zoom mode Image quality selection200% IiiOff Mode Low Power ModeAbout the International Energy Star Program Paper RecyclingSymbols Page Label IMPORTANT! Please Read FirstOther precautions Installation PrecautionsPrecautions for USE Other precautions Maintenance Safety of laser beamSafety switch Cdrh ActPage Limited Warranty for NEW Copier Model Page Main Body Names of PartsPaper width guides DrawerPaper stopper Stopper extension lockPower cord Document Processor connector Power switchFace-up tray Right cover anchor pinOperation panel Auto Clear function Auto Drawer Switching functionNames of Parts Preparations Loading paperLoading paper into a drawer Preparations Preparations Selecting the paper size Inch Specification Setting paper on the multi-bypass trayMetric Specification A4 A6R, and Folio Code number SizePreparations XXX Selecting the paper size standard settingSelecting the paper size temporary setting Thick Paper mode Attaching the face-up tray Basic Operation Basic copying procedureSetting the number of copies to be made Adjusting the copy exposureSetting an original Start copyingAt the end of copying Zoom mode Making enlarged and reduced copies50% Preset Zoom mode Low Power mode More about the Off mode Off modeBasic Operation Copy Functions Metric specificationLayout modes In-1Copy Functions When setting the originals on the platenWhen setting the originals in the Document Processor Press the 2in1/4in1 key until the 2in1 indicator lights Press the 2in1/4in1 key until the 4in1 indicator lights Selecting the borderline Code number Borderline types Selecting the order of 4-in-1 layoutCopy Functions Original Copy Press the Sort key to light the Sort indicator Sort modeUsing programmed settings to make copies Program functionRegistering the program Copy Default Settings Available default itemsDefault Description Available settings Reference Number Copy Default Settings Non-Standard Size Paper Width and it Mode ON/OFF Copy Default Settings Accessing and changing the default settings Sample User Copy Setting List Copy Default Settings Copy Default Settings Copy Default Settings Copy Default Settings Checking the total copy count and printing out a report Document Processor Optional EquipmentAcceptable originals Names of partsOptional Equipment Setting originals in the Document ProcessorSetting originals on the platen Additional Memory Paper FeederTroubleshooting Indication Procedure ReferenceIf one of the following indications is displayed Troubleshooting If paper jams Misfeed location indicatorsPaper jam inside the copier Removal proceduresPaper jam in a drawer Paper jam in the paper eject section Original jam in the optional Document Processor Paper jam in the multi-bypass trayTroubleshooting If other trouble occurs Trouble Checkpoint Procedure ReferenceTroubleshooting Cleaning the copier Maintenance and Operation InformationReplacing the toner container Maintenance and Operation Information Cleaner Home Position Cleaning the charger and the registration rollerClose the front cover Close the upper front cover Main Body SpecificationsDocument Processor option Paper Feeder optionAdditional Memory option Environmental Specifications Duplex 2-sided copyingPaper feed Available options Optional equipmentDocument Processor Additional Memory Paper Feeder Document ProcessorFunction selected first Function selected second Appendix Functions and settings combination chartNumerics IndexToner Coverage Report default setting Total copy count Memo Page Page 2003