Kyocera copier manual Preparations

Page 24

Section 3 PREPARATIONS

1 Pull the drawer all the way out of the copier.

IMPORTANT!

When pulling the drawer out of the copier, be sure to support it so that it doesn’t fall out suddenly.

2 Adjust the paper stopper in the rear portion of the drawer by pressing in on the release buttons and sliding the paper stopper to the fit the size of the paper being loaded.

NOTES

• The paper sizes are marked on the bottom of the drawer.

The factory default setting is for A4/Letter size paper.

For information on adjusting the paper stopper for Folio or Oficio II size paper, see “Adjusting the paper stopper for Folio or Oficio II size paper” on page 3-3.

3 Adjust the paper width guides on both sides of the drawer by pressing in on the release buttons and sliding the guides to fit the width of the paper being loaded in the drawer.

4 Set the paper in the drawer so that the leading edge is aligned against the paper stopper, but making sure that none of the paper gets caught on the overhanging tabs.

IMPORTANT!

ALWAYS adjust the paper stopper and paper width guides BEFORE loading paper into the drawer. Failure to do so may result in skewed paper feed and/or a paper jam.

Make sure that the paper is set securely against the paper stopper and the paper width guides. If there is any gap between the paper and the stopper or guides, readjust the paper stopper and/or the paper width guides, as appropriate.

When you are loading paper into the drawer, make sure that the side to be copied onto is facing downward.

Be sure to load paper so that it is not folded or curled, etc.

DO NOT load more paper than indicated by the lines located on the width guides.

NOTES

The paper sizes are marked on the bottom of the drawer.

The factory default setting is for A4/Letter size paper.

3-2

Image 24
Contents 1500 Page Copy Default Settings TroubleshootingMaintenance and Operation Information IMPORTANT! Please Read FirstContents Preset Zoom mode Image quality selection Eco-Copy mode See200% IiiLow Power Mode Off ModeAbout the International Energy Star Program Paper RecyclingSymbols Page IMPORTANT! Please Read First LabelInstallation Precautions Other precautionsPrecautions for USE Other precautions Safety of laser beam MaintenanceSafety switch Cdrh ActPage Limited Warranty for NEW Copier Model Page Names of Parts Main BodyDrawer Paper width guidesPaper stopper Stopper extension lockPower switch Power cord Document Processor connectorFace-up tray Right cover anchor pinOperation panel Auto Drawer Switching function Auto Clear functionNames of Parts Preparations Loading paperLoading paper into a drawer Preparations Preparations Selecting the paper size Setting paper on the multi-bypass tray Inch SpecificationMetric Specification A4 A6R, and Folio Code number SizePreparations Selecting the paper size standard setting XXXSelecting the paper size temporary setting Thick Paper mode Attaching the face-up tray Basic copying procedure Basic OperationAdjusting the copy exposure Setting the number of copies to be madeSetting an original Start copyingAt the end of copying Zoom mode Making enlarged and reduced copies50% Preset Zoom mode Low Power mode Off mode More about the Off modeBasic Operation Metric specification Copy FunctionsLayout modes In-1When setting the originals on the platen Copy FunctionsWhen setting the originals in the Document Processor Press the 2in1/4in1 key until the 2in1 indicator lights Press the 2in1/4in1 key until the 4in1 indicator lights Selecting the borderline Selecting the order of 4-in-1 layout Code number Borderline typesCopy Functions Sort mode Original Copy Press the Sort key to light the Sort indicatorUsing programmed settings to make copies Program functionRegistering the program Copy Default Settings Available default itemsDefault Description Available settings Reference Number Copy Default Settings Non-Standard Size Paper Width and it Mode ON/OFF Copy Default Settings Accessing and changing the default settings Sample User Copy Setting List Copy Default Settings Copy Default Settings Copy Default Settings Copy Default Settings Checking the total copy count and printing out a report Optional Equipment Document ProcessorAcceptable originals Names of partsSetting originals in the Document Processor Optional EquipmentSetting originals on the platen Paper Feeder Additional MemoryTroubleshooting Indication Procedure ReferenceIf one of the following indications is displayed Troubleshooting Misfeed location indicators If paper jamsRemoval procedures Paper jam inside the copierPaper jam in a drawer Paper jam in the paper eject section Paper jam in the multi-bypass tray Original jam in the optional Document ProcessorTroubleshooting Trouble Checkpoint Procedure Reference If other trouble occursTroubleshooting Maintenance and Operation Information Cleaning the copierReplacing the toner container Maintenance and Operation Information Cleaning the charger and the registration roller Cleaner Home PositionClose the front cover Close the upper front cover Specifications Main BodyDocument Processor option Paper Feeder optionAdditional Memory option Environmental Specifications Duplex 2-sided copyingPaper feed Optional equipment Available optionsDocument Processor Additional Memory Paper Feeder Document ProcessorAppendix Functions and settings combination chart Function selected first Function selected secondIndex NumericsToner Coverage Report default setting Total copy count Memo Page Page 2003