Kyocera copier manual Troubleshooting

Page 68

Section 8 TROUBLESHOOTING

Indication

Procedure

Reference

Page

 

 

 

 

 

 

 

 

“E72” appears on the copy quantity/

Originals for another job were set in the optional Document Processor

—

magnification display

during copying from the platen in the 2-in-1 or 4-in-1 layout mode or in

 

 

the Sort mode.

 

 

Remove the new originals from the Document Processor and, once the

 

 

copy operation for the 2-in-1 or 4-in-1 layout mode or the Sort mode is

 

 

completed, reset them on the original table and try to copy again.

 

 

 

 

“E90” appears on the copy quantity/

The copier’s memory is full.

—

magnification display

To copy from those originals already scanned:

 

 

Press the Recall%/Enter key and copying will begin. Once those copies

 

 

have been made, reset the originals that have not yet been copied and

 

 

press the Start key. Copying will continue.

 

 

To start the copy procedure once again from the beginning:

 

 

Press the Stop/Clear key, set a lesser number of originals and try to copy

 

 

again.

 

 

 

 

“OP” appears on the copy quantity/

The upper front cover or the front cover to the copier is open.

—

magnification display

Close the covers securely.

 

 

 

 

“OP1” appears on the copy quantity/

The left cover to the Document Processor is open.

—

magnification display

Close the cover securely.

 

 

 

 

“J” and a number appear on the copy

A paper jam has occurred.

8-3

quantity/magnification display

Refer to “If paper jams” on page 8-3and remove the jammed paper.

 

 

 

 

The Add Toner indicator lights

The toner supply has run low.

9-2

 

Copying will still be available for awhile, but will then become impossible.

 

 

Replace the toner container as soon as possible.

 

 

 

 

The Add Toner indicator lights and “E33”

Toner has run out so further copying is impossible.

9-2

appears on the copy quantity/magnification

Replace the toner container.

 

display

 

 

 

 

 

“C” and a number appear on the copy

Turn the power switch OFF ({) and then back ON ( ) again. If the error

—

quantity/magnification display

indication does not go out, make a note of the “C” and the number. Turn

 

 

the power switch OFF ({), remove the power cord, and contact your

 

 

service representative or an authorized service center.

 

 

 

 

“A” and a number appear on the copy

Turn the power switch OFF ({) and then back ON ( ) again. If the error

—

quantity/magnification display

indication does not go out, make a note of the “A” and the number. Turn

 

 

the power switch OFF ({), remove the power cord, and contact your

 

 

service representative or an authorized service center.

 

 

 

 

8-2

Page 67 Page 69
Image 68
Page 67 Page 69
Contents 1500 Page Copy Default Settings TroubleshootingMaintenance and Operation Information IMPORTANT! Please Read FirstContents Preset Zoom mode Image quality selection Eco-Copy mode See200% IiiLow Power Mode Off ModeAbout the International Energy Star Program Paper RecyclingSymbols Page IMPORTANT! Please Read First LabelInstallation Precautions Other precautionsPrecautions for USE Other precautions Safety of laser beam MaintenanceSafety switch Cdrh ActPage Limited Warranty for NEW Copier Model Page Names of Parts Main BodyDrawer Paper width guidesPaper stopper Stopper extension lockPower switch Power cord Document Processor connectorFace-up tray Right cover anchor pinOperation panel Auto Drawer Switching function Auto Clear functionNames of Parts Loading paper into a drawer PreparationsLoading paper Preparations Preparations Selecting the paper size Setting paper on the multi-bypass tray Inch SpecificationMetric Specification A4 A6R, and Folio Code number SizePreparations Selecting the paper size standard setting XXXSelecting the paper size temporary setting Thick Paper mode Attaching the face-up tray Basic copying procedure Basic OperationAdjusting the copy exposure Setting the number of copies to be madeSetting an original Start copyingAt the end of copying 50% Zoom modeMaking enlarged and reduced copies Preset Zoom mode Low Power mode Off mode More about the Off modeBasic Operation Metric specification Copy FunctionsLayout modes In-1When setting the originals on the platen Copy FunctionsWhen setting the originals in the Document Processor Press the 2in1/4in1 key until the 2in1 indicator lights Press the 2in1/4in1 key until the 4in1 indicator lights Selecting the borderline Selecting the order of 4-in-1 layout Code number Borderline typesCopy Functions Sort mode Original Copy Press the Sort key to light the Sort indicatorRegistering the program Using programmed settings to make copiesProgram function Default Description Available settings Reference Number Copy Default SettingsAvailable default items Copy Default Settings Non-Standard Size Paper Width and it Mode ON/OFF Copy Default Settings Accessing and changing the default settings Sample User Copy Setting List Copy Default Settings Copy Default Settings Copy Default Settings Copy Default Settings Checking the total copy count and printing out a report Optional Equipment Document ProcessorAcceptable originals Names of partsSetting originals in the Document Processor Optional EquipmentSetting originals on the platen Paper Feeder Additional MemoryIf one of the following indications is displayed TroubleshootingIndication Procedure Reference Troubleshooting Misfeed location indicators If paper jamsRemoval procedures Paper jam inside the copierPaper jam in a drawer Paper jam in the paper eject section Paper jam in the multi-bypass tray Original jam in the optional Document ProcessorTroubleshooting Trouble Checkpoint Procedure Reference If other trouble occursTroubleshooting Maintenance and Operation Information Cleaning the copierReplacing the toner container Maintenance and Operation Information Cleaning the charger and the registration roller Cleaner Home PositionClose the front cover Close the upper front cover Specifications Main BodyAdditional Memory option Document Processor optionPaper Feeder option Paper feed Environmental SpecificationsDuplex 2-sided copying Optional equipment Available optionsDocument Processor Additional Memory Paper Feeder Document ProcessorAppendix Functions and settings combination chart Function selected first Function selected secondIndex NumericsToner Coverage Report default setting Total copy count Memo Page Page 2003
Top Page Image Contents