Kyocera copier manual Troubleshooting, If one of the following indications is displayed

Page 67

Section 8 TROUBLESHOOTING

If one of the following indications is displayed

When any of the following indications appears on the copy quantity/magnification display, perform the corresponding procedure.

	Indication	Procedure	Reference
	Indication	Procedure	Page
			Page


	“E07” appears on the copy quantity/	The size of paper registered in the default settings is different than the	3-1
	magnification display	size of the paper actually used. Check the paper size.
		Pull out the corresponding drawer and then push it back in to delete the
		error indications.

	“E11” appears on the copy quantity/	The Paper Feeder was selected, but the upper drawer is not installed or is	—
	magnification display	not inserted properly.
		Push the upper drawer securely into the copier.

	“E12” appears on the copy quantity/	When printing out a list or report, there was no 8 1/2" × 11" or A4 size	—
	magnification display	paper available.
		Press the Paper Select key to select the source of paper feed and then
		press the Start key. Print out will be performed onto paper from the
		selected location.

	“E31” appears on the copy quantity/	The amount of waste toner in the copier has reach the acceptable limit.	—
	magnification display	Contact your service representative or an authorized service center.

	“E32” appears on the copy quantity/	The toner container is not installed in the copier.	9-2
	magnification display	Install the toner container.

	“E70” appears on the copy quantity/	If the optional Document Processor is installed on your copier, there are	—
	magnification display	originals remaining on the original table.
		Remove the originals, reset them on the original table and try to copy
		again.

	“E71” appears on the copy quantity/	The copier will attempt to make copies from any originals that remain	—
	magnification display	uncopied.
		Reset all of the originals on the original table and try to copy again.

8-1

Image 67

Contents 1500 Page IMPORTANT! Please Read First Copy Default SettingsTroubleshooting Maintenance and Operation InformationContents Iii Preset Zoom mode Image quality selectionEco-Copy mode See 200%Paper Recycling Low Power ModeOff Mode About the International Energy Star ProgramSymbols Page Label IMPORTANT! Please Read FirstOther precautions Installation PrecautionsPrecautions for USE Other precautions Cdrh Act Safety of laser beamMaintenance Safety switchPage Limited Warranty for NEW Copier Model Page Main Body Names of PartsStopper extension lock DrawerPaper width guides Paper stopperRight cover anchor pin Power switchPower cord Document Processor connector Face-up trayOperation panel Auto Clear function Auto Drawer Switching functionNames of Parts Loading paper PreparationsLoading paper into a drawer Preparations Preparations Selecting the paper size Code number Size Setting paper on the multi-bypass trayInch Specification Metric Specification A4 A6R, and FolioPreparations XXX Selecting the paper size standard settingSelecting the paper size temporary setting Thick Paper mode Attaching the face-up tray Basic Operation Basic copying procedureStart copying Adjusting the copy exposureSetting the number of copies to be made Setting an originalAt the end of copying Making enlarged and reduced copies Zoom mode50% Preset Zoom mode Low Power mode More about the Off mode Off modeBasic Operation In-1 Metric specificationCopy Functions Layout modesCopy Functions When setting the originals on the platenWhen setting the originals in the Document Processor Press the 2in1/4in1 key until the 2in1 indicator lights Press the 2in1/4in1 key until the 4in1 indicator lights Selecting the borderline Code number Borderline types Selecting the order of 4-in-1 layoutCopy Functions Original Copy Press the Sort key to light the Sort indicator Sort modeProgram function Using programmed settings to make copiesRegistering the program Available default items Copy Default SettingsDefault Description Available settings Reference Number Copy Default Settings Non-Standard Size Paper Width and it Mode ON/OFF Copy Default Settings Accessing and changing the default settings Sample User Copy Setting List Copy Default Settings Copy Default Settings Copy Default Settings Copy Default Settings Checking the total copy count and printing out a report Names of parts Optional EquipmentDocument Processor Acceptable originalsOptional Equipment Setting originals in the Document ProcessorSetting originals on the platen Additional Memory Paper FeederIndication Procedure Reference TroubleshootingIf one of the following indications is displayed Troubleshooting If paper jams Misfeed location indicatorsPaper jam inside the copier Removal proceduresPaper jam in a drawer Paper jam in the paper eject section Original jam in the optional Document Processor Paper jam in the multi-bypass trayTroubleshooting If other trouble occurs Trouble Checkpoint Procedure ReferenceTroubleshooting Cleaning the copier Maintenance and Operation InformationReplacing the toner container Maintenance and Operation Information Cleaner Home Position Cleaning the charger and the registration rollerClose the front cover Close the upper front cover Main Body SpecificationsPaper Feeder option Document Processor optionAdditional Memory option Duplex 2-sided copying Environmental SpecificationsPaper feed Additional Memory Paper Feeder Document Processor Optional equipmentAvailable options Document ProcessorFunction selected first Function selected second Appendix Functions and settings combination chartNumerics IndexToner Coverage Report default setting Total copy count Memo Page Page 2003