NEC LCD2335WXM Important Information, Canadian Department of Communications Compliance Statement

Page 3

Important Information

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

Canadian Department of Communications Compliance Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regula- tions.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.

FCC Information

1.Use the attached specified cables with the MultiSync® LCD2335WXMTM(L234GC) color monitor so as not to interfere with radio and television reception.

(1)Please use the supplied power cord or equivalent to ensure FCC compliance.

(2)Please use the supplied shielded video signal cable, 15-pin mini D-SUB to 15-pin mini D-SUB.

(3)Please use the supplied AC adapter.

Use of other cables and adapters may cause interference with radio and television reception.

2.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: ”How to Identify and Resolve Radio-TV Interference Problems.“ This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

1

Image 3
Contents LCD2335WXMTM Index Canadian Department of Communications Compliance Statement Important InformationSafety Precautions, Maintenance & Recom- mended Use Cleaning the LCD PanelCleaning the Cabinet Contents Rear view of main body Component Names and FunctionsMain Unit Front view of main bodyClose the battery cover Remote ControlOpen the battery cover Installing the batteriesSource Remote ControlInterface for Arm Applications Installation InstructionsViewing Angle Adjustment Detaching Main Body From Its StandVHF300-Ohm antenna / UHF antenna Connecting to a Antenna / CablePrecautions when connecting the antenna When both VHF and UHF antennas are combinedConnecting to a Video Components TerminalSub Remarks Prevention of Screen Burn Connecting to a PCOperating Instructions Turning Power On and OffPower Operation Lamp Power lampVolume Adjustment Selecting AV InputsAudio Mute Picture Parameters Selected Setup hint CharactersPC Parameters Audio SettingChannel Setting Auto Program settingFine Tune setting Channel Edit setting Cinema Aspect mode Select 43 and 169 aspect modeThere are 4 selections PanoramicPicture-in-Picture Selected Setup hintLarge PIP Position Small Medium PBP Picture in PictureSelecting PIP size Source PIPSelect PIP Source Setting Up PIP through On Screen Main MenuMain Select PIP sizePICTUREIN Picture Change PIP PositionMulti PIP Stereo and SAP 2nd Audio program sound program Other FunctionsMono and SAP 2nd Audio program sound program Stereo soundMpaa Rating Parental ControlsMotion Picture Ratings Chart Mpaa RatingTV PG Rating TV Parental Guide Ratings Chart General Setting Shadow Captions MenuTEX1---TEXT2 BOXFeatures Nopicture TroubleshootingPhase next. RGB input Check to see that the signal cable is properly ConnectedCheck Contrast and brightness Settings Adjust them for higher contrast and brightnessSymptom Point to check Symptom Possible reason Remedy SymptomsReferences NEC-MitsubishiMonitorCustomerService&SupportPC Input SpecificationsLimited Warranty TCO’99 TCO’99 DeclarationoftheManufacturer NEC LCD2335WXM