NEC L234GC manual Check to see that the signal cable is properly Connected, Phase next. RGB input

Page 32

Troubleshooting continued

Symptoms

If the solution does not correct the symptoms, please contact your local Service center for assistance.

WARNING

DO NOT OPEN THE MONITOR.

Self servicing can be hazardous. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified personnel.

Symptom				Point to check		See Page
Symptom				Point to check

There is no picture and the power-indicating lamp		Check to see that the power cable is			properly	11
is off.		connected.
		Press the main switch.

The message “No cable connected” or “Going to		No sync signal is detected.
sleep” is displayed.		Check that the signal cable is properly connected.
		Check that the signal cable is properly connected.
There is no picture and the power indicating lamp		Make sure that the computer, imaging equipment,
lights orange.		Make sure that the computer, imaging equipment,
lights orange.		etc., is turned on.
		etc., is turned on.
		Make sure the computer is not in power-save mode.
		Ensure that the input selection matches the
		connection terminal.

The message “Invalid Mode.” is displayed.		An input signal is received abnormally.				32
		Ensure that the input signal matches the monitor
		specifications.
		Check to see that the signal cable is properly
		connected.

The power indicating lamp is lit normally but there		Check	the	contrast and brightness	settings	13
is no picture.		(adjust them for higher contrast and brightness).				13
is no picture.		(adjust them for higher contrast and brightness).
		Check to see that the signal cable is properly
		connected.

The display image appears slanted.		Adjust	the	clock frequency and the	phase.	14
		(Adjust the clock frequency first, the dot clock				14
Text displayed across the screen appears		(Adjust the clock frequency first, the dot clock
Text displayed across the screen appears		phase next.) (RGB input)
vertically streaked, with the characters in vertical		phase next.) (RGB input)
vertically streaked, with the characters in vertical
columns blurred.

Text displayed across the screen appears blurred.		Adjust the clock phase till the desired clarity is				14
A fine pattern flickers when displayed on the		obtained.				14
A fine pattern flickers when displayed on the		obtained.
screen.		(RGB input)

The remote control does not work.		Ensure that the batteries in the remote control are				5
		inserted with the correct polarity.
		Check to see that the batteries in the remote
		control are functional.

30

Image 32

Contents LCD2335WXMTM Index Important Information Canadian Department of Communications Compliance StatementCleaning the Cabinet Safety Precautions, Maintenance & Recom- mended UseCleaning the LCD Panel Contents Component Names and Functions Main UnitFront view of main body Rear view of main bodyRemote Control Open the battery coverInstalling the batteries Close the battery coverRemote Control SourceInstallation Instructions Viewing Angle AdjustmentDetaching Main Body From Its Stand Interface for Arm ApplicationsConnecting to a Antenna / Cable Precautions when connecting the antennaWhen both VHF and UHF antennas are combined VHF300-Ohm antenna / UHF antennaSub Remarks Connecting to a Video ComponentsTerminal Connecting to a PC Prevention of Screen BurnTurning Power On and Off Power Operation LampPower lamp Operating InstructionsAudio Mute Volume AdjustmentSelecting AV Inputs Selected Setup hint Characters Picture ParametersAudio Setting PC ParametersFine Tune setting Channel SettingAuto Program setting Channel Edit setting Aspect mode Select 43 and 169 aspect mode There are 4 selectionsPanoramic CinemaSelected Setup hint Picture-in-PicturePicture in Picture Selecting PIP sizeSource PIP Large PIP Position Small Medium PBPSetting Up PIP through On Screen Main Menu MainSelect PIP size Select PIP SourceMulti PIP PICTUREIN PictureChange PIP Position Other Functions Mono and SAP 2nd Audio program sound programStereo sound Stereo and SAP 2nd Audio program sound programParental Controls Mpaa RatingTV PG Rating Motion Picture Ratings ChartMpaa Rating TV Parental Guide Ratings Chart General Setting Captions Menu TEX1---TEXT2BOX ShadowFeatures Troubleshooting NopictureCheck to see that the signal cable is properly Connected Check Contrast and brightness SettingsAdjust them for higher contrast and brightness Phase next. RGB inputSymptom Point to check Symptoms Symptom Possible reason RemedyNEC-MitsubishiMonitorCustomerService&Support ReferencesSpecifications PC InputLimited Warranty TCO’99 TCO’99 DeclarationoftheManufacturer NEC LCD2335WXM