NEC LCD2335WXM, L234GC manual Remote Control, Open the battery cover, Installing the batteries

Page 7

Component Names and Functions continued

Remote Control

LED INDICATION

POWER ON/OFF

SLEEP

CH-LOCK

ASPECT

PIP

STILL

VOLUME UP / DN (ST)

MENU

PROGRAM / ADJUST (WX)

ENTER

DISPLAY

AV2

AV1

RGB-1VGA

Installing the Batteries

1. Open the battery cover.

z Slide back and remove the battery cover in the direction of the arrow.

2. Installing the batteries.

zInstall two included Size AA batteries

observing the correct polarities(+,-).

TV TUNER

SOURCE SELECT

ZOOM

CCD (Close Caption Display)

SWAP

CH UP / DN (ST)

MUTE

LAST-CH

SELECT (ST)

MTS

NUMBER KEYPAD

AV3

AV4

RGB-2 DVI

Handling the Remote Control

Use the remote control within about 16 feet from front of the unit’s remote- control sensor and within 30 degrees on both sides.

Within 30 degrees

Within 30 degrees

About 10 feet

About 10 feet

About 16 feet

3. Close the battery cover.

z Replace the battery cover in the direction of the arrow and snap it back into place.

CAUTION

z Do not mix new and old batteries together. The batteries could explode or leak, resulting in fires, physical injury, or stains.

z When inserting batteries, observe their correct polarities as marked on the product. If inserted in the wrong direction, the batteries could explode or leak, resulting in fires, physical injury, or stains.

ATTENTION

zDo not drop the remote control.

zTo avoid possible failures, do not splash the remote control with water or put it on a wet object.

zIf leaving the remote control out of use for an extended period of time, remove the batteries from it.

zIf the remote control does not respond properly, replace the batteries.

zStrong light such as direct sunlight exposed on the photoreceptor of the remote control can cause operational failure. Position this unit to avoid direct contact with such light.

5

Image 7

Contents LCD2335WXMTM Index Canadian Department of Communications Compliance Statement Important InformationCleaning the LCD Panel Safety Precautions, Maintenance & Recom- mended UseCleaning the Cabinet Contents Rear view of main body Component Names and FunctionsMain Unit Front view of main bodyClose the battery cover Remote ControlOpen the battery cover Installing the batteriesSource Remote ControlInterface for Arm Applications Installation InstructionsViewing Angle Adjustment Detaching Main Body From Its StandVHF300-Ohm antenna / UHF antenna Connecting to a Antenna / CablePrecautions when connecting the antenna When both VHF and UHF antennas are combinedTerminal Connecting to a Video ComponentsSub Remarks Prevention of Screen Burn Connecting to a PCOperating Instructions Turning Power On and OffPower Operation Lamp Power lampSelecting AV Inputs Volume AdjustmentAudio Mute Picture Parameters Selected Setup hint CharactersPC Parameters Audio SettingAuto Program setting Channel SettingFine Tune setting Channel Edit setting Cinema Aspect mode Select 43 and 169 aspect modeThere are 4 selections PanoramicPicture-in-Picture Selected Setup hintLarge PIP Position Small Medium PBP Picture in PictureSelecting PIP size Source PIPSelect PIP Source Setting Up PIP through On Screen Main MenuMain Select PIP sizeChange PIP Position PICTUREIN PictureMulti PIP Stereo and SAP 2nd Audio program sound program Other FunctionsMono and SAP 2nd Audio program sound program Stereo soundMpaa Rating Parental ControlsMpaa Rating Motion Picture Ratings ChartTV PG Rating TV Parental Guide Ratings Chart General Setting Shadow Captions MenuTEX1---TEXT2 BOXFeatures Nopicture TroubleshootingPhase next. RGB input Check to see that the signal cable is properly ConnectedCheck Contrast and brightness Settings Adjust them for higher contrast and brightnessSymptom Point to check Symptom Possible reason Remedy SymptomsReferences NEC-MitsubishiMonitorCustomerService&SupportPC Input SpecificationsLimited Warranty TCO’99 TCO’99 DeclarationoftheManufacturer NEC LCD2335WXM