NEC L234GC, LCD2335WXM manual Remote Control, Source

Page 8

Component Names and Functions continued

Remote Control (continued)

POWER

Press this button to turn the TV on or off.

SLEEP

Press this button to activate the Sleep Timer menu.

CH-LOCK

Press this button to select the V-chip function.

ASPECT

Press this button to selcet how the picture is displayed on the screen; 4:3,16:9, Panoramic, or Cinema modes

PIP

Press this button to show the PIP and change the size of PIP.

VOL

Press these two buttons to adjust the volume up or down

MENU

Press this button to select the

On Screen Display Menu.

DISPLAY

Press this button to show the input signal information.

AV2

Press this button to select the S-VIDEO INPUT.

AV1

Press this button to select the

COMPOSITE INPUT.

RGB1

Press this button to select the RGB1 VGA INPUT.

RGB2

Press this button to select the RGB2 DVI INPUT.

TV

Press this button to choose TV as the source.

Source

Press this button to select the INPUT Source.

ZOOM

Press this button to change the picture

CCD

Press this button to show the Close Caption menu.

SWAP

Press this button to exchange main picture with PIP picture.

STILL

Press this button to freeze the picture. Press it again to return to normal operation.

CH

Press these two buttons to select the channel up or down.

MUTE

Press this button to turn off the sound. Press it once more or press the S volume up button to return the sound.

LAST CH

Press this button to return to the last Channel viewed.

MTS

Press this button to select Multi- channel television sound. This button operates only in the TV mode.

NUMBERS KEYPAD

Press these buttons to access the corresponding TV channels.

AV3

Press this button to select the AV3 YCbCr / YPbPr INPUT.

AV4

Press this button to select the AV4 YCbCr / YPbPr INPUT.

6

Image 8

Contents LCD2335WXMTM Index Important Information Canadian Department of Communications Compliance StatementCleaning the Cabinet Safety Precautions, Maintenance & Recom- mended UseCleaning the LCD Panel Contents Component Names and Functions Main UnitFront view of main body Rear view of main bodyRemote Control Open the battery coverInstalling the batteries Close the battery coverRemote Control SourceInstallation Instructions Viewing Angle AdjustmentDetaching Main Body From Its Stand Interface for Arm ApplicationsConnecting to a Antenna / Cable Precautions when connecting the antennaWhen both VHF and UHF antennas are combined VHF300-Ohm antenna / UHF antennaSub Remarks Connecting to a Video ComponentsTerminal Connecting to a PC Prevention of Screen BurnTurning Power On and Off Power Operation LampPower lamp Operating InstructionsAudio Mute Volume AdjustmentSelecting AV Inputs Selected Setup hint Characters Picture ParametersAudio Setting PC ParametersFine Tune setting Channel SettingAuto Program setting Channel Edit setting Aspect mode Select 43 and 169 aspect mode There are 4 selectionsPanoramic CinemaSelected Setup hint Picture-in-PicturePicture in Picture Selecting PIP sizeSource PIP Large PIP Position Small Medium PBPSetting Up PIP through On Screen Main Menu MainSelect PIP size Select PIP SourceMulti PIP PICTUREIN PictureChange PIP Position Other Functions Mono and SAP 2nd Audio program sound programStereo sound Stereo and SAP 2nd Audio program sound programParental Controls Mpaa RatingTV PG Rating Motion Picture Ratings ChartMpaa Rating TV Parental Guide Ratings Chart General Setting Captions Menu TEX1---TEXT2BOX ShadowFeatures Troubleshooting NopictureCheck to see that the signal cable is properly Connected Check Contrast and brightness SettingsAdjust them for higher contrast and brightness Phase next. RGB inputSymptom Point to check Symptoms Symptom Possible reason RemedyNEC-MitsubishiMonitorCustomerService&Support ReferencesSpecifications PC InputLimited Warranty TCO’99 TCO’99 DeclarationoftheManufacturer NEC LCD2335WXM