Lexmark C780, C782 manual Adjusting Power Saver, Encrypting the disk

Page 80

Administrative support

Adjusting Power Saver

To adjust the Power Saver setting:

1Make sure the printer is on and Ready appears on the display.

2Press on the operator panel.

3Press until Settings appears, and then press .

4Press until Setup Menu appears, and then press .

5Press until Power Saver appears, and then press .

6Using the right and left arrows on the operator panel, enter the number of minutes for the printer to wait before entering Power Saver.

The settings available range from 1–240 minutes.

7Press .

Submitting Selection appears.

Note: You can also adjust the Power Saver setting by issuing a Printer Job Language (PJL) command. For more information, see the Technical Reference available on the Lexmark Web site at www.lexmark.com/publications.

Encrypting the disk

Warning: All resources on the hard disk and RAM will be deleted.

Note: This setting is only available when a hard disk is installed.

1Turn the printer off.

2Press and hold and while turning the printer on.

3Release both buttons when Performing Self Test appears on the display.

The printer performs its power-on sequence, and then Config Menu appears on the first line of the display.

4Press until Disk Encryption appears, and then press .

5Press until Enable appears, and then press .

Contents will be lost. Continue? appears.

6Press until Yes appears, and then press . The Encrypting Disk progress bar appears.

7When disk encryption has finished, press .

8Press until Exit Config Menu appears, and then press .

To disable disk encryption:

1Turn the printer off.

2Press and hold and while turning the printer on.

3Release both buttons when Performing Self Test appears on the display.

The printer performs its power-on sequence, and then Config Menu appears on the first line of the display.

4Press until Disk Encryption appears, and then press .

Adjusting Power Saver

80

Image 80

Contents C780, C782 Trademarks Safety informationEdition October Contents Contents Installing and removing options Input options Output options Internal optionsInstalling a 2000-sheet drawer Installing and removing optionsContinue with Installing a 500-sheet drawer Installing a 500-sheet drawer Installing a duplex unit Installing the printer Installing an output expander Installing and removing options Installing a 5-bin mailbox Installing and removing options Removing the system board access cover Installing a StapleSmart finisherInstalling memory and option cards Installing a memory card Installing an option-added firmware card Installing a hard disk Installing and removing options Installing an option card Card FunctionAccessing the printer system board Removing memory and option cardsRemoving memory cards Removing an option card Removing a hard diskInstalling and removing options Reinstalling the system board access cover Removing an option-added firmware cardPrinting Understanding the printer operator panelStatus Indicates Button Function Sending a job to printPrinting Printing from a USB flash memory device Canceling a job from a computer running Windows Canceling a print jobCanceling a job from the printer operator panel Printing a menu settings Printing a network setupCanceling a job from a Macintosh computer Canceling a job from a Macintosh computer running Mac OSPrinting a font sample list Printing a directory listLoading the trays Loading 500-sheet traysPrinting Loading the 2000-sheet tray Printing Loading the multipurpose feeder Printing Loading the trays Loading the multipurpose feeder Printing on specialty media transparencies, labels, otherWindows Select File Print Linking traysMac OS Linking output bins Holding a job in the printerPrinting and deleting held jobs Value DescriptionPrinting confidential jobs WindowsMacintosh Print Time FiltersEnter PIN At the printerEntering a personal identification number PIN Verify Print Reserve PrintRepeat Print Copies & Pages or General pop-up menu, choose Job RoutingAt the printer Print All Delete All JobName1 JobName2Storing supplies Tips for successful printingStoring paper Avoiding jams Paper characteristics WeightMedia guidelines PaperMedia specifications Unacceptable paperSelecting preprinted forms and letterhead Media specifications Selecting paperStoring paper Media specifications Printing on letterhead TransparenciesEnvelopes Selecting transparenciesLabels Storing media Card stockMedia sizes and support Identifying media sources and specificationsDimensions Media support by type for optional features Optional Finisher Standard Offset StapleMedia types and weights input options Media types and weights output options Envelopes2Maximum 2,3 Grain longMaximum Labels- 2,4Media capacities Paper labelsVinyl labels EnvelopesDetermining the status of supplies Ready. Tray 1 Low, TrayStatus / Supplies View supplies Y KSupply Menu selection item What the setting does Conserving suppliesOrdering supplies Print cartridges Maintaining the printerToner waste container Fuser and ITUOrdering a fuser Type of fuser Printer voltage Part numberOrdering staple cartridges Recycling Lexmark productsOrdering an image transfer unit and transfer roller Clearing paper jams Identifying jamsAccess doors and trays Clearing paper jamsUnderstanding jam messages Paper jam messagesMessage Check Areas What to do Expander jams Area MArea B Clearing the entire paper pathArea a Area C Area DArea Tx Area T1Area E Area L Area JArea K Clearing mailbox, finisher, or output expander jams Area M Clearing fuser jamsClearing fuser jams Clearing image transfer unit jams Clearing paper jams Clearing paper jams Clearing paper jams If you still need help Adjusting operator panel brightness and contrast Disabling operator panel menusEnabling operator panel menus Restoring factory default settingsAdministrative support Adjusting Power Saver Encrypting the diskSetting security using the Embedded Web Server EWS Setting the system passwordUsing the secure Embedded Web Server Click ConfigurationSupporting IPSec Internet Protocol Security Using Secure modeClick TCP/IP Port Access Using 802.1x Authenticating Click 802.1x AuthenticationClick Menu Lockout Setup Locking the operator panel menusBlack only mode Confidential Print SetupClick Confidential Print Setup Printing LockoutDisabling size sensing Using the Coverage EstimatorSize sensing Configuring printer alerts Using the Setup MenuUsing MarkVision Professional Using MarkVision MessengerOnline customer support Calling for service Symptom Cause SolutionChecking an unresponsive printer Check the Print as image boxSet Page Protect to Off from Print Recovery Solving printing problemsTroubleshooting Output expander jams Area M Solving mailbox problemsFor more informations, see Clearing mailbox, finisher, or Option Action Solving option problemsSee Solving high capacity feeder problems Solving high capacity feeder problems Problem SolutionSolving paper feed problems Solving print quality problemsSee Loading the trays or Loading Paper pathTop to Bottom or Left to Right Marks occur repeatedly only in one colorMultiple times on a Marks occur down the page repeatedly in allTo be replaced Cartridges BCD E Solving color quality problems Frequently asked questions FAQ about color printingWhat is RGB color? How does the printer know what color to print?What is Manual Color Correction? Is it possible to increase the gloss in the printed output?Cmyk What are Detailed Color Samples and how do I access them? European Community EC directives conformity Electronic emission noticesAvis de conformité aux normes de l’industrie du Canada 102 Industry Canada compliance statement Noise emission levels Hinweis zum GS-ZeichenGerman GS mark notice Durchschnittlicher Schallpegel dBA in 1 m UmkreiPower Saver Mode Description Power consumptionProduct energy consumption Total energy usage106 Part Name Hazardous Substances or Elements China RoHSLaser advisory label Statement of Limited Warranty Laser notice109 Index Index PIN112