Emerson 5150 Installation, How to Install the Connectivity Module on Asco 940/962 ATSs

1-1 Installation

How to Install the Connectivity Module

on 7000 & 4000 Series and Series 300 ATSs

The Connectivity Module (CM) mounts on a DIN rail under the ATS Controller (Group 5 & 1). A short serial cable connects the CM to the Controller. If a Power Manager (PM) or Digital Power Meter (DPM) is present, a long serial cable connects the CM to the PM. Refer to installation drawings provided and follow the steps below to install the Connectivity Module.

Connectivity Module Kit		Connectivity Module Kit
K889950		K889950-001 for
for 7000 & 4000 Series		7000 & 4000 Series
and Series 300 only		and Series 300
		with PM or DPM
Connectivity	629800-004	Connectivity	629800-004
Module 5150		Module 5150
DIN Rail and	754607	DIN Rail and	754607
Hardware		Hardware
10-in. Serial		10-in. Serial
Cable for	629798-001	Cable for	629798-001
Controller		Controller
		4-ft Serial
		Cable for	629798-002
		PM or DPM *

*A 9-foot serial cable (629798-004) is required for G7ATB, G7ACTB, G7ADTB.

!DANGER

To avoid possible shock, burns, or death, deenergize all electrical sources to the ATS before installing the Connectivity Module.

1.De-energize both Normal and Emergency sources that feed the ATS. Open enclosure door and check with a non-contact AC voltage detector.

2.Mount the DIN rail (supplied in the kit) onto two studs (on the door) below the Controller. Connectivity Module will mount on the right side.

3.Install Connectivity Module onto DIN rail by hooking the bottom of module on bottom of DIN rail and rocking it upward unit it snaps in place.

4.Install the 10-inch serial cable between the Controller receptacle (J7 on Group 5, J4 on Group 1) and the Connectivity Module J1 receptacle.

5.If a PM (or DPM) is present, connect the 4-foot serial cable between the PM J5 receptacle (or DPM J2 receptacle) and the Connectivity Module J2 receptacle.*

Now test communications (go to page 1-2).

Connectivity Module

How to Install the Connectivity Module on ASCO 940/962 ATSs

The Connectivity Module (CM) mounts on a DIN rail near the ATS Control Panel. A separate power supply is needed unless it is connected to a Power Manager (PM). Group 6A/7A Control Panel must have a Serial Communication Kit added. A single communication cable (2 twisted pairs and overall shield connects the CM to the Control Panel). Refer to installation drawings provided and follow the steps below to install the Connectivity Module.

Connectivity Module Kit					Connectivity Module Kit
K889953					K889953-001
for ASCO 940/962 only					for ASCO 940/962 with PM
Connectivity		629800-004			Connectivity	629800-004
Module 5150					Module 5150
DIN Rail and			754610		DIN Rail and	754610
Hardware					Hardware
Serial Com.					Serial Com.
Kit for Group			467508		Kit for Group	467508
6A/7A CP *					6A/7A CP *
					Serial Cable	629798-002
					for PM
* Serial	communication &				transient protection	boards.
Required					Communication Cable
Power Supply **				(4 wires and an overall shield)
not supplied					not supplied
24 Vdc, 80 mA ** use				Belden 9842, 9829, 89729, 82729 or
16 AWG wire				Alpha 6202C, 6222C, 58902 only

**If a Power Manager (PM) is present, a power supply is not needed for the Connectivity Module (CM). The serial cable from the PM provides the power to the CM.

!DANGER

To avoid possible shock, burns, or death, deenergize all electrical sources to the ATS before installing the Connectivity Module.

1.De-energize both Normal and Emergency sources that feed the ATS. Open enclosure door and check with a non-contact AC voltage detector.

2.Mount DIN rail (supplied in the kit) onto two studs (on the door) below or adjacent to the Control Panel.

3.Install the Connectivity Module onto DIN rail.

4.Prepare and connect the specified communication cable between the Control Panel terminals and the Connectivity Module J4 terminals as listed below:

5.Prepare and connect the 24 Vdc power supply to the Connectivity Module. Use 16 AWG wiring to J5 terminal plug (1 is + positive, 2 is – negative).

Now test communications (go to page 1-2).