Emerson CATALOG 5150 installation manual Connectivity Module Status LEDs

Page 9

Connectivity Module

Status LEDs ix

Status LEDs

	LED	LED Description	LED Function / Mode of Operation
	POWER	Power indication status.	Solid GREEN – functioning as a Connectivity Module (Acc. 72E).
		Power indication status.
		GREEN/AMBER	Solid AMBER – functioning as a Serial Module (Acc. 72A).
		GREEN/AMBER


	RX	Data receiving status.	Blinking GREEN – indicates receiving data from a client.
	RX	GREEN	Blinking GREEN – indicates receiving data from a client.
		GREEN

	TX	Data transmit status.	Blinking GREEN – indicates transmitting data to a client.
	TX	GREEN	Blinking GREEN – indicates transmitting data to a client.
		GREEN

	LINK	Link status.	Solid GREEN – indicates active Ethernet connection.
	LINK	GREEN	Solid GREEN – indicates active Ethernet connection.
		GREEN

	CH1	Client connection status.	Blinking GREEN – indicates active Ethernet client connection.
	CH1	GREEN
		GREEN

			Blinking YELLOW then off – indicates server disconnection because of
	CH2	Additional Diagnostic LED.	Ethernet client inactivity.
		Additional Diagnostic LED.
		YELLOW	Solid YELLOW then off – indicates server disconnection due to Ethernet
		YELLOW

			client disconnection.

			Off – indicates no error.
		Diagnostic.	Short blinking RED then off – indicates active client/server write process.
	DIAG	Diagnostic.
	DIAG	RED	Long blinking light then off – indicates server is receiving unrecognized
		RED
			request packet from an Ethernet client.
			Solid RED – indicates major error.

Image 9

Contents 381333-367 B Connectivity ModuleIi Welcome Connectivity Module Who Should Use this Installation ManualPrerequisites Important informationInstallation Overview SpecificationsCheck the DIP Switch Settings for RS485 DIP Switch on bottom of unitIv Outline and Mounting Drawing Connectivity Module Wiring Diagrams Connectivity Module Connectivity Module Wiring Diagrams Vii Wiring Diagrams Connectivity Module Connectivity Module Wiring Diagrams LED Description LED Function / Mode of Operation Status LEDsConnectivity Module Status LEDs How to Install the Connectivity Module on Asco 940/962 ATSs InstallationHow to Test Communication to the Connectivity Module Connectivity Module InstallationInstallation Connectivity Module Http//169.254.1.1/config.htmGroup 5 Controller Configuration right side Device Configurator Screen for 7000 & 4000 Series ATSsConnectivity Module server Configuration left side Device Configurator Screen for 7000 & 4000 Series ATSsPower Manager or Power Meter Configuration Input Name & Output Names Power Manager only7000 & 4000 Series ATSs Connectivity Module Detail Screen for 7000 & 4000 Series ATSs Group 1 Controller Configuration right side Device Configurator Screen for Series 300 ATSsDevice Configurator Screen for Series 300 ATSs Series 300 ATSs Connectivity ModuleConnectity Module Series 300 ATSs Detail Screen for Series 300 ATSs Detail Screen for Series 300 ATSs with a Power ManagerGroup 7A Controller Configuration right side Device Configurator Screen for Asco 940/962 ATSsDevice Configurator Screen without Power Manager Device Configurator Screen with Power ManagerDetail Screen for Asco 940/962 ATSs with a Power Manager Detail Screen for Asco 940/962 ATSsAsco 940/962 ATSs Connectivity Module Power Manager or Power Meter Configuration Detail Screen for Digital Power Meters connected to a Load Detail Screen for Power Managers connected to a LoadDetail Screen for Power Detail Screen for Power Managers connected to a GeneratorDetail On Local Area Connection Properties screen Select All Programs Accessories Command Prompt Problem Cause Connectivity Module Troubleshooting A-3Read Requests Third Party Modbus Device ConfigurationSnmp Trap messages Connectivity Module Snmp Internet-standard Protocol A-5Snmp Internet-standard Protocol Connectivity Module Problem Cause SolutionRow IP Address Subnet Mask Gateway Serial NoCatalog No Address set ATS Controller PM or DPM Index