Primera Technology C-1000 manual Appendix a Command Language Quick Reference, Command SET for Ppla

Page 29

Appendix A: Command Language Quick Reference

This section lists all internal software commands for the printer if you are installing it in a “legacy” application in which a specific printer programming language is being used. For more information please refer to the Programmer’s Manual, available separately from the factory or your Authorized Reseller. This section does not apply if you are using the printer with the included Windows-compatible driver and Windows application software.

A. COMMAND SET FOR PPLA

The following commands are for Printer Programming Language A.

System Setting Commands

These commands will cause related parameters to be saved in the permanent storage, E2PROM. The parameters will be stored unless they are changed by commands or a reset from the front panel.

Command

Description

Parameter

Factory default

<STX>KI4n

Media empty

n:

‘0’ - disable

enabled

 

check

 

‘1’ - enable.

 

<STX>KI7n

Set ribbon

n:

‘0’ – DT,

TT with ribbon

 

mode

 

‘1’ – TT.

 

<STX>KI8n

Set baud rate

m: ‘0’ – 9600,

9600 baud.

 

 

 

‘1’ – 600,

 

 

 

 

‘2’ – 2400,

 

 

 

 

‘3’ – 19200,

 

 

 

 

‘4’ – 4800,

 

 

 

 

‘5’ – 38400,

 

 

 

 

‘6’ – 1200,

 

 

 

 

‘7’ – 9600.

 

<STX>KI;1

Select alternate

!KI;0 - selects

 

 

Control codes

 

standard

 

 

 

 

control

 

 

 

 

codes.

 

<STX>KXnnnn

Set continuous

nnnn: a 4-digit

Valid under

 

label length

 

number,

Windows driver

 

 

 

in mm

Label Dr.

Command Language Quick Reference 25

Image 29
Contents Cyclone Bar Code Label Printer Printing History Table of Contents Page Thank YOU… Getting StartedUnpacking and Inspection Choosing a Good LocationGetting Started Front Panel LED IndicatorsIdentifying the Parts Buttons Rear Panel Applying PowerConnecting the Printer to Your Computer Getting Started Data format Speed baud rateParity HandshakingLoading Labels or Tags Loading MediaLoading Media Loading the Ribbon Loading Media Performing a Self Test Label Sensor CalibrationSelf Test Pattern Resetting the Printer to Factory Default ConditionInstalling the Printer Driver Using the Printer With WindowsHOW to USE the Driver Driver InstallationDetails Print to the following port Parameter settingOrientation Using the Label Dr PaperPaper source Media choiceDevice Options CopiesMore Options Printing Labels Troubleshooting Troubleshooting & MaintenanceProblems with media ContinuousOther problems Problems with ribbonMaintenance Miscellaneous other problemsRecovery Troubleshooting and Maintenance Command SET for Ppla Appendix a Command Language Quick ReferenceSystem Setting Commands Command Description Parameter Factory defaultCommand Description Response Contents Interaction CommandsSymbol Code hexadecimal System Level CommandsCommand Description Formatting CommandsCommandsDescription Editing CommandsObject String Description Font Downloading CommandsCommand Description Parameter Command SET for PplbLEx,y,hlen,vlen Command Language Quick Reference Introduction Appendix B Interface SpecificationsSerial Connection with hostBaud rate Printer Terminal/HostAuto Polling Parallel CentronicsAppendix C Ascii Table Internal Fonts Appendix D Fonts and Bar Codes for PplaFont FontFont Font Points Points ECMA-94 Roman-8PC-A Legal PC-BGreek Russian Internal Bar Codes Fonts and Bar Codes for Ppla Fonts and Bar Codes for Ppla Fonts and Bar Codes for Ppla Appendix E Fonts and Bar Codes for Pplb Symbol Set Fonts and Bar Codes for Pplb Fonts and Bar Codes for Pplb Internal Bar Codes Fonts and Bar Codes for Pplb Printer Specifications Appendix F SpecificationsPrinter Programming Language A, Ppla SpecificationPrinter Programming Language B, Pplb Index